Where is the software download for the PocketPC version of Lady Heather? Tia Jerry K1JOS
-----Original Message----- From: Didier [mailto:shali...@gmail.com] Sent: Saturday, August 17, 2013 23:30 To: Robert Atkinson; Discussion of precise time and frequency measurement Subject: Re: [time-nuts] Lady Heather without a PC Does the iPAQ have a serial port? I have a Dell PDA that runs Pocket PC2003 with WiFi and Bluetooth but no serial port. Didier Robert Atkinson <robert8...@yahoo.co.uk> wrote: >Hi, > >This is not my software. See >http://fuzzythinking.com/projects/thunderhead/ >I just used the complied file, but the source code is there of you want > >to change it. The iPAQ I built in was an H2200 series running PocketPC >2002. I've also ran it on a H3900 series (H3950) running PocketPC 2003. >I used an SD card to store the exe file. A quick check on ebay shows >2200 iPAQs on buy it now for $25. > >Robert G8RPI. > >________________________________ > From: Chris Albertson <albertson.ch...@gmail.com> >To: Robert Atkinson <robert8...@yahoo.co.uk>; Discussion of precise >time and frequency measurement <time-nuts@febo.com> >Sent: Friday, 16 August 2013, 19:44 >Subject: Re: [time-nuts] Lady Heather without a PC > > > >What OS runs on the IPAQ? > >Did you have to re-build LH from source? > >Edit: OK now I see you are running some other software called >"thunderhead". Same questions apply > > > >On Thu, Aug 15, 2013 at 1:17 PM, Robert Atkinson ><robert8...@yahoo.co.uk> wrote: > >Hi Chris, >>I've posted this before, but it's worth saying again. I use the >PocketPC version of Lady Heather on an IPAQ. These are available for >next to nothing on Ebay and can run in a dock on the bench or you can >gut it and embed it in a cased Thunderbolt. worn out batteries are not >an issue as we have constant power available. They just need 5V. One >with an SD card slot is good so you don't have to re-load the code from >a PC if the power does go out. >> >> >>Robert G8RPI. >> >> >>________________________________ >> From: Chris Albertson <albertson.ch...@gmail.com> >>To: Discussion of precise time and frequency measurement ><time-nuts@febo.com> >>Sent: Wednesday, 14 August 2013, 18:36 >>Subject: Re: [time-nuts] ThunderBolt Display >> >> >>What was the problem you found. Other then a "new to you" platform? >I'm >>trying to understand why reading serial data would be hard. >> >>An advantage of the Adruino is that you don't need to make a PCB. >Even if >>you want to do something like add a graphical display or and SD card >for >>logging they just plug in, no solder required. >> >>Of course the pre-buillt display is even easier but can't be modified. >> >>One of my loner term goals is to move lady heather like functions onto >a >>small uP based device. It seems wasteful to use a PC for this. >> >> >>On Wed, Aug 14, 2013 at 10:16 AM, Russ Ramirez ><russ.rami...@gmail.com>wrote: >> >>> Yeah, after trying to (reliably) get the time out of the pertinent >TSIP >>> message using an Arduino UNO, I can understand your statement Adam >about >>> the Arduino approach. It kinda works, but it felt like I was >fighting the >>> implementation of the controller card and that I should cut-over to >my own >>> solution using an Atmel, PIC or TI chip that I could just load C >code into. >>> One of this lists members gave me the code I needed, so ironically >using >>> the UNO made the project more difficult. >>> >>> Russ >>> K0WFS >>> _______________________________________________ >>> time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to >>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >>> and follow the instructions there. >>> >> >> >> >>-- >> >>Chris Albertson >>Redondo Beach, California >>_______________________________________________ >>time-nuts mailing list -- time-nuts@febo.com >>To unsubscribe, go to >https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >>and follow the instructions there. >>_______________________________________________ >>time-nuts mailing list -- time-nuts@febo.com >>To unsubscribe, go to >https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >>and follow the instructions there. >> > > >-- > >Chris Albertson >Redondo Beach, California >_______________________________________________ >time-nuts mailing list -- time-nuts@febo.com >To unsubscribe, go to >https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >and follow the instructions there. -- Sent from my Nexus 7 tablet. _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
