Hi Volker One possibility, as I found with one of these recently, is that your oscillator has aged such that the required EFC voltage for 10MHz output is now outside the range provided by the board. The EFC behaviour can be tracked if Lady Heather is enabled from switch on and the DAC voltage monitored. The EFC voltage should start at 3 volts, in my case reported by LH as 3.000002 Volts, and will sit at this level until enough satellites are being tracked for the board to decide it can start the conditioning process, at which point the DAC voltage will ramp upwards over the course of a few seconds until the point is reached where the oscillator frequency crosses 10MHz and the control loop takes over. All standard stuff of course but, as you've discovered, if the oscillator hasn't reached 10MHz by the time the EFC voltage reaches, in my case anyway, approximately 5.6 volts the board's "OSC" report switches to "BAD" and "Normal OSC age" switches to "OSC age alarm" and LH highlights both in red. The EFC voltage finishes its ramp at 6 Volts, reported as 6.000004 Volts, and then just sits there, all exactly as you're seeing. Having removed my "faulty" oscillator, something that needs to be done VERY carefully to avoid damage to the board, I found that it required an EFC voltage of just under 6.6 Volts for the the output frequency to reach 10MHz. The seller, fluke.l, was very helpful as always and offered to supply a replacement 34310-T oscillator, this one did have it's required EFC voltage in the correct range and resolved the problem. However, whilst waiting for the replacement to arrive I left the original oscillator on test and monitoring it for a while suggested that the only thing "wrong" with it was the required EFC voltage, so I reconnected it to the board using a wired lash-up on the bench with a simple 2 Volt level shifter inserted into the control loop and did indeed get a locked condition with Lady H reporting the DAC voltage from the board as close to 4.5 volts. This suggests that whilst the board design requires the oscillator EFC Voltage at 10 MHz to be between 3 and 6 Volts an oscillator that falls outside this range shouldn't automaticall be assumed to be "faulty" in more general terms, although it's obviously getting a bit long in the tooth and that doesn't help much if it happens to be soldered into your circuit board ! Whilst it is possible to remove and replace the original oscillator there is an alternative to physical replacement, one which I've now implemented, and this uses the mounting positions already available beneath the oscillator, not usable though until it's removed, to fit a couple of SMA or SMB connectors. These two connectors couple the 10MHz signal from the oscillator into the board (J9) and the EFC Voltage out to the oscillator (J10). Although there is a regulated supply available from the oscillator, which might be expected to supply the EFC circuitry, in practice this connection does not seem to be required. I have not investigated further as yet to determine whether the board auto senses and uses this supply if it is present, or whether it always just ignores it, but it doesn't seem to be an issue either way and it's interesting to note, at the extremes anyway, that LH does report the DAC voltage to be the same in both instances. The oscillator can be powered from the board or given its own supply, in which case the only required connections between them are the two coax leads. Using this arrangement, and some variation of a positive or negative level shifter if required, it becomes possible to use different oscillators with the Nortel board and it does become an even more interesting toy. One limitation though when using the Nortel boards in this way is that they don't seem to share the versatility of the Thunderbolt when it comes to modifying the oscillator conditioning parameters. It's suggested in the LH documentation that such commands are currently "undocumented" but that also leaves the possibility that any such change might only be a firmware option. If anyone has further information on this that would be much appreciated. I've been sufficiently impressed with the modified unit that I'm seriously considering modifying another one, even though it doesn't actually "need" it, although not over enthusiastic about repeating the oscillator removal. However, an added bonus with this configuration is that it's also more forgiving when it comes to any damage caused during removal of the original oscillator, since the pads for the external connectors are separate from the internal oscillator pads. Obviously it needs to be ensured that any necessary continuity is maintained but that could be easier if a board mounted oscillator is no longer required. The later single board unit, the NTBW50AA, has a similar external connector arrangement but in this case the connector pads are available without removing the original oscillator. This hints at the possibility that perhaps a simple track interruption might allow fitting of an external oscillator with the original still onboard but examination suggests that the onboard connections route first to the internal oscillator so that would probably still need to be removed. Regards Nigel GM8PZR In a message dated 23/01/2014 23:59:34 GMT Standard Time, ail...@t-online.de writes:
Hi! I bought a Trimble/Nortel GPSDO http://www.ebay.de/itm/300933951405?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m 1497.l2648 and Lady Heather's now tells me that everything is alright - except - DAC 6.000004V - OSC BAD - osc age alarm The rectangle "10MHz" output signal (J5) shows a signal at about 9.8MHz (a deviation of about 200kHz), wobbling 4Hz up and down. Oddly enough, the direct oscillator output (J4) shows a sine wave at a stable 10.0000004MHz (a deviation of 0.4Hz). It seems to me it's not the oscillator that is bad but the servo loop - what can I do? Thank you Volker _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.