Hi Ignacio,
Thanks for your comments also. I will open up the unit and see if I can find
any dry or poorly soldered joints, etc.
Best regards, Jim Rowe
-----Original Message-----
From: EB4APL
Sent: Saturday, February 08, 2014 12:21 AM
To: Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] How I got my FE-5680A to lock in Sydney, Australia
Hi,
I second the idea about a mechanical issue. When I opened my FRS-C I
found that one of the connector pins had never been soldered, it only
made mechanical contact with the PBC. Perhaps it showed an intermittent
failure and was retired with low hours.
Ignacio EB4APL
On 07/02/2014 3:54, Ed Palmer wrote:
Hi Jim,
On 2/6/2014 3:32 PM, Jamieson (Jim) Rowe wrote:
Hi again folks,
You may (or may not) recall that a month or so ago, I asked for any
information that might be available regarding how to fix a ‘used’
FE-5680A rubidium module from China (via ebay) which was tested by the
supplier in China as working OK, but would not seem to lock up to
rubidium here in Sydney. There wasn’t a great deal of info available, it
seems, so I kept on checking ideas myself – mostly with no luck. The
module would never lock, but kept cycling back and forth between about
9.999770MHz and 10.000036MHz – ‘searching’ for a lock, but never finding
it.
Anyway, a couple of days ago I was reading more about the operation of
rubidium vapour oscillators, and noticed that the ‘filter cell’ is very
sensitive to magnetic fields – hence the mu-metal shielding case, and
also for the ‘C-tuning’ coil. And I wondered if the main reason why the
FE-5680A had apparently worked in China, but wouldn’t lock up in Sydney
(Australia) might be caused by the fact that Quangzhou (China) is in the
northern hemisphere while I’m ‘down under’ in the southern hemisphere –
where the earth’s field is presumably somewhat different, in terms of
both strength and direction.
So I decided to test this in a crude way, by inverting the FE-5680A and
seeing what happened. And – lo and behold – it locked up within 2.5
minutes, and stayed locked until I turned off the power and let it go
cold again. The next morning I applied power again, and within 3 minutes
it locked up again with no problems. And it’s been locked up now for over
48 hours...
My first thought was to make a typical 'down-under' joke and suggest you
run the 5680A upside down, but you beat me to it! :)
So it seems that the different magnetic field here may have been the
problem – either that, or it may have received a ‘jolt’ in transit, which
prevented in from locking unless it was inverted.
But how do I tell which of these explanations is right, without ‘opening
her up’ again and looking for some kind of subtle physical fault?
Another idea: perhaps the mu-metal shield case had acquired a small dose
of magnetisation in transit (via a physical shock, or from a strong field
metal detector). I guess in this case that I would have to remove the two
halves of the case, and bake them in a furnace to demagnetise them again.
My very limited knowledge regarding mu-metal is that it is so magnetically
'soft' that it can't be magnetized. If it was somehow magnetized,
inverting the unit wouldn't make any difference, would it?
Or should I just run the FE-5680A upside down permanently – the simple
but ‘crude’ answer?
I don't believe for a second (pun intended) that the earth's magnetic
field has any effect on the locking of your 5680A. It's just not strong
enough. The same applies to the C-field which can only nudge the
frequency one way or another by a small amount.
Since flipping the unit DID make a difference, my money would be on a
trivial, boring mechanical issue inside the unit. Could be a bad solder
joint, broken wire, floating piece of debris, or something like that.
Worst case might be a broken glue joint somewhere in the physics package.
That could be ugly. I would definitely open it up and see if anything
falls out.
I’m not sure if this FE-5680A has the ‘C-tuning’ gizmo fitted, or wired
up. Am I right in thinking that another approach might be to try varying
the tuning via the RS-232C serial port? Does this work via the C-tuning
coil anyway, or by tweaking the DDS?
The RS-232 commands affect the DDS - assuming your unit does have one. It
will have no effect on the locking, only on the output frequency.
A few years ago I bought a dead Datum SLCR Rb standard. It's a cousin to
the LPRO. I thought I'd learn some things by trying to fix it. The
problem was intermittent. I tore it apart and found that one of the legs
of the crystal had never been soldered! Never overlook the obvious.
I hope a much more experienced time nut can provide a few answers,
please.
Maybe the blind leading the blind is a closer description.
Ed
Jim Rowe
_______________________________________________
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.