Why to people always build 10MHz GPSDOs? If the use of the GPSDO is to drive a microwave, why not build a MUCH higher frequency GPSDO. Is the reason that 10MHz crystals just happen to be very good and there are not good 100MHz ovenized crystals? Or for portable use could you not use the 1PPS signal to discipline a microwave oscillator.
Scaling up 10MHz is going to make noise, so why not start way higher and do less scaling On Wed, Dec 21, 2016 at 11:06 AM, Eric Haskell <eric_hask...@hotmail.com> wrote: > Hello Time Nuts, I have been on the group and have promoted it to other > folks for a while but this may be my first post here. > > I am microwave amateur radio operator and I have question to pose relating > to the use of GPSDO's with amateur radio for microwave communication. > > First, the more generic question. A friend was discussing using a eBay > purchased Trimble 57963-D for providing a 10 MHz refrence for his portable > microwave station (primarly at 10GHz). He wants a clean high stability 10 > MHz refrence mainly to lock the station LO. First I think a GPSDO is > overkill for this application and I am thinking that a good surplus > ovenized crystal oscillator should get him to within a few Hz after warm up > and a Rb could do better but may have short term stability that may degrade > phase noise of the LO. I am concerned that a GPSDO is not designed for > portable operations. Moving it should probably force a new site survey > which may take a day or more to complete before it goes into disciplining > mode so you would loose any potential benefit of a GPSDO by moving around > frequently. If he wants to do this I think he should leave it connected at > his home location for an extended time (several days at least), then when > he want to go portable (roving), he should > disconnect the GPS antenna entirely to force the unit into holdover mode > maintain continuous power with battery backup which should maintain the > internal OCXO very close to the target frequence and allow the holdover > algorithm to compensate for OCXO for aging and best it can. I would guess > that if he chooses to used the GPSDO with the antenna connected it would > probably never exit the site survey mode and you would have the output > default to the last known good DAC value when it was been disciplined so it > would be operating as a OCXO only (although potentially starting from a > very accurate starting point, if it had been in use at a fixed location for > a good while) before going portable. Is this a correct view of the > situation? Any recommendations? > > I also know of a fellow who has developed some excellent open source Linux > software to drive an Ettus Research USRP microwave SDR transceiver for > amateur radio microwave applications. His code also has features to > calculate antenna baring and with other available code compensates for > satellite Doppler shift and/or synchronize digital communication modes > using the GPS coordinates and timing data. He has a built in interface for > a Trimble Thunderbolt for this purpose. I think it also might be a better > solution to use a OCXO for 10 MHz and a cheap USB GPS sensor for location? > Is there a cheep USB GPS that provides PPS? Any recommendations? > > I have seen simpler GPS controlled 10 MHz sources like the Miller design > that divides down a 10 MHz ref and compares it to a 10 KHz output from a > Jupiter T GPS to tweak the ref freq that may or may not be better suited to > this application as it may add phase noise to the LO but would be more real > time in it's GPS correction to the reference frequency. > > Regards, > > > Norman Eric Haskell > > KC4YOE > > Keller, TX USA > _______________________________________________ > time-nuts mailing list -- time-nuts@febo.com > To unsubscribe, go to https://www.febo.com/cgi-bin/ > mailman/listinfo/time-nuts > and follow the instructions there. > -- Chris Albertson Redondo Beach, California _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
