On Tuesday, April 9, 2013 4:38:23 PM, Benoît Thébaudeau wrote: > Hi Fabio, > > On Tuesday, April 9, 2013 2:46:21 PM, Fabio Estevam wrote: > > On Tue, Apr 9, 2013 at 9:30 AM, Fabio Estevam <feste...@gmail.com> wrote: > > > > > Just tested v10 on mx31pdk. > > > > > > As reported in v9 I start to get reboots and never reach the prompt. > > > > > > Then I disabled watchdog options in mx31pdk.h and I get the following: > > > > > > U-Boot 2013.04-rc1-14135-gab21c72-dirty (Apr 09 2013 - 09:23:01) > > > > > > CPU: Freescale i.MX31 rev 2.0 at 532 MHz. > > > Reset cause: POR > > > Board: MX31PDK > > > DRAM: 128 MiB > > > NAND: 256 MiB > > > In: serial > > > Out: serial > > > Err: serial > > > Net: > > > > > > (Board hangs here). > > > > > > When I tested v9 and removed watchdog support I was able to get into > > > the U-boot prompt. > > > > I just added "#define DEBUG" in arch/arm/lib/board to start debugging > > this and for my surprise I can reach the prompt now: > > > > U-Boot 2013.04-rc1-14135-gab21c72-dirty (Apr 09 2013 - 09:35:51) > > > > U-Boot code: 87F00000 -> 87F2C34C BSS: -> 87F3137C > > CPU: Freescale i.MX31 rev 2.0 at 532 MHz. > > Reset cause: POR > > Board: MX31PDK > > monitor len: 0003137C > > ramsize: 08000000 > > TLB table from 87ff0000 to 87ff4000 > > Top of RAM usable for U-Boot at: 87ff0000 > > Reserving 196k for U-Boot at: 87fbe000 > > Reserving 640k for malloc() at: 87f1e000 > > Reserving 32 Bytes for Board Info at: 87f1dfe0 > > Reserving 160 Bytes for Global Data at: 87f1df40 > > New Stack Pointer is: 87f1df30 > > RAM Configuration: > > Bank #0: 80000000 128 MiB > > relocation Offset is: 000be000 > > monitor flash len: 000310F4 > > Now running in RAM - U-Boot at: 87fbe000 > > NAND: 256 MiB > > In: serial > > Out: serial > > Err: serial > > Net: smc911x-0 > > Hit any key to stop autoboot: 0 > > MX31PDK U-Boot > > > > > I remember to have added "#define DEBUG" in v9 as well, so looks like > > the behavior between v9 and v10 is consistent. > > > > Now we need to understand why the prompt is not reached without > > ""#define DEBUG". > > Can you try different values for the following configs in mx31pdk.h? > - CONFIG_SYS_NAND_U_BOOT_SIZE > - CONFIG_SPL_TEXT_BASE > - CONFIG_SYS_TEXT_BASE > - (CONFIG_ENV_OFFSET) > - (CONFIG_ENV_OFFSET_REDUND) > > I would try: > - 0x40000 for CONFIG_SYS_NAND_U_BOOT_SIZE > - 0x86000000 for CONFIG_SPL_TEXT_BASE > - 0x87000000 for CONFIG_SYS_TEXT_BASE
I have retrieved your previous test trace: --- U-Boot 2013.01 (Feb 22 2013 - 16:25:48) CPU: Freescale i.MX31 rev 2.0 at 532 MHz. Reset cause: POR Board: MX31PDK DRAM: 128 MiB (hangs here). --- So it does not hang at the same step. Can you try to disable CONFIG_CMD_NET or to comment out eth_initialize() in arch/arm/lib/board.c? Do you know if something has changed in this function recently, or if there is something about it that has not yet been merged in the arm tree? Best regards, Benoît _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot