Hi Simon,
On 12/08/14 17:48, Simon Glass wrote:
Hi Nikita,
On 11 August 2014 10:22, Nikita Kiryanov <nik...@compulab.co.il> wrote:
Add initial support for Compulab CM-FX6 CoM.
Support includes MMC, SPI flash, and SPL with dynamic DRAM detection.
[..snip..]
board/compulab/cm_fx6/common.h | 36 ++++
board/compulab/cm_fx6/imximage.cfg | 8 +
board/compulab/cm_fx6/spl.c | 400 +++++++++++++++++++++++++++++++++++++
boards.cfg | 2 +
include/configs/cm_fx6.h | 211 +++++++++++++++++++
I think you need Kconfig etc. here? Also we don't use boards.cfg
anymore. I pushed a tree to u-boot-x86.git branch cm_fx6 which hacks
in a few of these things as an example (enough to make it build
anyway).
[..snip..]
+#
+ifdef CONFIG_SPL_BUILD
+obj-y = common.o spl.o
+else
+obj-y = common.o cm_fx6.o
+endif
Note this doesn't apply or build for me on mainline due to missing
Kconfig stuff. I might be missing a patch.
diff --git a/boards.cfg b/boards.cfg
index e3a0726..308b94e 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -334,6 +334,8 @@ Active arm armv7 mx6 freescale
mx6sabresd
Active arm armv7 mx6 freescale mx6slevk
mx6slevk
mx6slevk:IMX_CONFIG=board/freescale/mx6slevk/imximage.cfg,MX6SL
Fabio Estevam
<fabio.este...@freescale.com>
Active arm armv7 mx6 gateworks gw_ventana
gwventana
gw_ventana:IMX_CONFIG=board/gateworks/gw_ventana/gw_ventana.cfg,MX6QDL,SPL
Tim Harvey <thar...@gateworks.com>
Active arm armv7 mx6 solidrun hummingboard
hummingboard_solo
hummingboard:IMX_CONFIG=board/solidrun/hummingboard/solo.cfg,MX6S,DDR_MB=512
Jon Nettleton
<jon.nettle...@gmail.com>
+Active arm armv7 mx6 compulab cm_fx6
cm_fx6
+-
Nikita Kiryanov
<nik...@compulab.co.il>
Active arm armv7 omap3 - overo
omap3_overo -
Steve Sakoman <sako...@gmail.com>
Active arm armv7 omap3 - pandora
omap3_pandora -
Grazvydas Ignotas <nota...@gmail.com>
Active arm armv7 omap3 8dtech eco5pk
eco5pk -
Raphael Assenat <r...@8d.com>
We don't use this file anymore.
diff --git a/include/configs/cm_fx6.h b/include/configs/cm_fx6.h
new file mode 100644
[..snip..]
+
+/* Machine config */
+#define CONFIG_MX6
+#define CONFIG_MX6QDL
+#define CONFIG_CM_FX6
Should these three be defined in the Kconfig file instead? What does
CONFIG_CM_FX6 represent? There might be a CONFIG_TARGET_CM_FX6 defined
by Kconfig.
+#define CONFIG_SYS_LITTLE_ENDIAN
+#define CONFIG_MACH_TYPE 4273
+#define CONFIG_SYS_HZ 1000
Yes you're correct. I was hoping this would be accepted before all the
Kconfig changes took effect but things didn't work out that way.
I'll rebase and post a new version.
Regards,
Simon
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
