Hi Nikita,
On 08/10/14 20:13, Nikita Kiryanov wrote:
> Add support for SATA.
>
> Cc: Igor Grinberg <grinb...@compulab.co.il>
> Cc: Stefano Babic <sba...@denx.de>
> Cc: Tom Rini <tr...@ti.com>
> Signed-off-by: Nikita Kiryanov <nik...@compulab.co.il>
> ---
> Changes in V2:
> - No changes
>
> board/compulab/cm_fx6/cm_fx6.c | 90
> ++++++++++++++++++++++++++++++++++++++++++
> board/compulab/cm_fx6/common.h | 13 ++++++
> include/configs/cm_fx6.h | 36 ++++++++++++++++-
> 3 files changed, 138 insertions(+), 1 deletion(-)
>
> diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c
> index 76d7430..8a48f9d 100644
> --- a/board/compulab/cm_fx6/cm_fx6.c
> +++ b/board/compulab/cm_fx6/cm_fx6.c
[...]
> @@ -23,6 +25,94 @@
>
> DECLARE_GLOBAL_DATA_PTR;
>
> +#ifdef CONFIG_DWC_AHSATA
> +static int cm_fx6_issd_gpios[] = {
> + /* The order of the GPIOs in the array is important! */
> + CM_FX6_SATA_PHY_SLP,
> + CM_FX6_SATA_NRSTDLY,
> + CM_FX6_SATA_PWREN,
> + CM_FX6_SATA_NSTANDBY1,
> + CM_FX6_SATA_NSTANDBY2,
> + CM_FX6_SATA_LDO_EN,
> +};
> +
> +static void cm_fx6_sata_power(int on)
Will it be/look better to use bool here?
> +{
> + int i;
> +
> + if (!on) { /* tell the iSSD that the power will be removed */
> + gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 1);
> + mdelay(10);
> + }
> +
> + for (i = 0; i < ARRAY_SIZE(cm_fx6_issd_gpios); i++) {
> + gpio_direction_output(cm_fx6_issd_gpios[i], on);
> + udelay(100);
> + }
> +
> + if (!on) /* for compatibility lower the power loss interrupt */
> + gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0);
> +}
[...]
> +static void cm_fx6_setup_issd(void)
> +{
> + SETUP_IOMUX_PADS(sata_pads);
> + /* Make sure this gpio has logical 0 value */
> + gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0);
> + udelay(100);
> +
> + cm_fx6_sata_power(0);
> + mdelay(250);
> + cm_fx6_sata_power(1);
> +}
> +
> +#define CM_FX6_SATA_INIT_RETRIES 10
> +int sata_initialize(void)
> +{
> + int err, i;
> +
> + cm_fx6_setup_issd();
> + for (i = 0; i < CM_FX6_SATA_INIT_RETRIES; i++) {
> + err = setup_sata();
> + if (err) {
> + printf("SATA setup failed: %d\n", err);
> + return err;
> + }
> +
> + udelay(100);
> +
> + err = __sata_initialize();
> + if (!err)
> + break;
> +
> + /* There is no device on the SATA port */
> + if (sata_port_status(0, 0) == 0)
> + break;
> +
> + /* There's a device, but link not established. Retry */
> + }
> +
> + return err;
> +}
> +#else
> +static void cm_fx6_setup_issd(void) {}
Why do you need this one?
It is only called from sata_initialize(), which is inside
#ifdef CONFIG_DWC_AHSATA
and is not available otherwise.
> +#endif
> +
> #ifdef CONFIG_SYS_I2C_MXC
> #define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
> PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
[...]
> diff --git a/include/configs/cm_fx6.h b/include/configs/cm_fx6.h
> index adfd55e..88925cd 100644
> --- a/include/configs/cm_fx6.h
> +++ b/include/configs/cm_fx6.h
> @@ -132,6 +132,19 @@
> "mmcboot=echo Booting from mmc ...; " \
> "run mmcargs; " \
> "run doboot\0" \
> + "satadev=0\0" \
> + "sataroot=/dev/sda2 rw rootwait\0" \
> + "sataargs=setenv bootargs console=${console} " \
> + "root=${sataroot} " \
> + "${video}\0" \
> + "loadsatabootscript=fatload sata ${satadev} ${loadaddr} ${bootscr}\0" \
> + "satabootscript=echo Running bootscript from sata ...; " \
> + "source ${loadaddr}\0" \
> + "sataloadkernel=fatload sata ${satadev} ${loadaddr} ${kernel}\0" \
> + "sataloadfdt=fatload sata ${satadev} ${fdtaddr} ${fdtfile}\0" \
Can we switch to use load instead of explicit fatload?
[...]
--
Regards,
Igor.
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
