Hi Prafulla, On Thursday 21 May 2009 22:24:32 Prafulla Wadaskar wrote: > Contributors: > Yotam Admon <yo...@marvell.com> > Michael Blostein <michae...@marvell.com > > Reviewed by: Ronen Shitrit <rshit...@marvell.com> > Signed-off-by: Prafulla Wadaskar <prafu...@marvell.com> > --- > Change log: > v2: entire rewrite/restructure of v1 > used small names for variable/function names > readl/writel used to access SoC registers > Soc registers accssed using pointers through net device struct > miiphy registration done for external smi read/write access > miiphy_link used to detect phy link presence > cleaned for cosmetic changes
Please find a comment below. > diff --git a/drivers/net/kirkwood_egiga.h b/drivers/net/kirkwood_egiga.h > new file mode 100644 > index 0000000..9f3908e > --- /dev/null > +++ b/drivers/net/kirkwood_egiga.h > @@ -0,0 +1,828 @@ > +/* > + * (C) Copyright 2009 > + * Marvell Semiconductor <www.marvell.com> > + * Prafulla Wadaskar <prafu...@marvell.com> > + * > + * based on - Driver for MV64360X ethernet ports > + * Copyright (C) 2002 rab...@galileo.co.il > + * > + * See file CREDITS for list of people who contributed to this > + * project. > + * > + * This program is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of > + * the License, or (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * You should have received a copy of the GNU General Public License > + * along with this program; if not, write to the Free Software > + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, > + * MA 02110-1301 USA > + */ > + > +#ifndef __EGIGA_H__ > +#define __EGIGA_H__ > + > +#define MAX_KWGBE_DEVS 2 /*controller has two ports */ <snip> > +/* Default port serial control value */ > +#define PORT_SERIAL_CONTROL_VALUE_TMP \ > + KWGBE_FORCE_LINK_PASS | \ > + KWGBE_DIS_AUTO_NEG_FOR_DUPLX | \ > + KWGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL | \ > + KWGBE_ADV_NO_FLOW_CTRL | \ > + KWGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX | \ > + KWGBE_FORCE_BP_MODE_NO_JAM | \ > + (1 << 9) | \ > + KWGBE_DO_NOT_FORCE_LINK_FAIL | \ > + KWGBE_DIS_AUTO_NEG_SPEED_GMII | \ You disable speed auto-negotiation here. Why are you doing this? Using auto- negotiation should be the default operation mode from my point of view. > + KWGBE_DTE_ADV_0 | \ > + KWGBE_MIIPHY_MAC_MODE | \ > + KWGBE_AUTO_NEG_NO_CHANGE | \ > + KWGBE_MAX_RX_PACKET_1552BYTE | \ > + KWGBE_CLR_EXT_LOOPBACK | \ > + KWGBE_SET_FULL_DUPLEX_MODE | \ > + KWGBE_DIS_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX | \ > + KWGBE_SET_MII_SPEED_TO_100 > + > +#ifdef CONFIG_SYS_MII_MODE > +#define PORT_SERIAL_CONTROL_VALUE \ > + PORT_SERIAL_CONTROL_VALUE_TMP | \ > + KWGBE_SET_GMII_SPEED_TO_10_100 > +#else > +#define PORT_SERIAL_CONTROL_VALUE \ > + PORT_SERIAL_CONTROL_VALUE_TMP | \ > + KWGBE_SET_GMII_SPEED_TO_1000 > +#endif If you need a fixed link speed configuration we should perhaps add a configuration option for this. What do you think? Best regards, Stefan ===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: off...@denx.de ===================================================================== _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot