Hi, On 27 November 2014 at 06:21, Hyungwon Hwang <human.hw...@samsung.com> wrote: > This patch adds support for Odroid-XU3. > > Signed-off-by: Hyungwon Hwang <human.hw...@samsung.com> > Tested-by: Lukasz Majewski <l.majew...@samsung.com> > Acked-by: Lukasz Majewski <l.majew...@samsung.com> > Cc: Minkyu Kang <mk7.k...@samsung.com> > Cc: Lukasz Majewski <l.majew...@samsung.com> > --- > Changes for v3: > - Remove unnecessary node from DT file > - Remove unnecessary features from config file > - Remove unnecessary macros from board-specific header file > - Fix some trivial typos in comments > > Changes for v4: > - Add MMC FIFO buffer's configuration to DT file > - Make CONFIG_OF_CONTROL be set by the target information > - Add basic document to doc/README.odroid-xu3 > - Add CONFIG_CMD_EXT4 to config file > - Add environment size and offset to config file > - Add extra default environment to make bootable without modification > - Remove unnecessary features from config file > > Changes for v5: > - Convert /include/ to #include in DT file > > Changes for v6: > - Separate out the documentation to new commit > - Remove unnecessary header file inclusions from the board-specific setup file > - Make the function board_clock_init be declared, only when > CONFIG_BOARD_EARLY_INIT_F is defined > > Changes for v7: > - Remove OF_CONTROL dependency from !SPL_BUILD > > Changes for v8: > - Remove unnecessary properties in DT mmc node > > Changes for v9: > - Remove useless variables in the default environment > - Replace the detailed information to the reference to the documentation
Great to see this series. I wanted to test it earlier but had problems with it not being reliable. I tracked this down to a uSD card (which works fine on other boards but boots reliably only to SPL on XU3). > > arch/arm/cpu/armv7/exynos/Kconfig | 5 ++ > arch/arm/dts/Makefile | 3 +- > arch/arm/dts/exynos5422-odroidxu3.dts | 57 +++++++++++++++ > board/samsung/odroid-xu3/Kconfig | 12 +++ > board/samsung/odroid-xu3/MAINTAINERS | 6 ++ > board/samsung/odroid-xu3/Makefile | 7 ++ > board/samsung/odroid-xu3/odroid-xu3.c | 122 +++++++++++++++++++++++++++++++ > board/samsung/odroid-xu3/setup.h | 95 ++++++++++++++++++++++++ > configs/odroid-xu3_defconfig | 4 + > include/configs/odroid.h | 5 -- > include/configs/odroid_xu3.h | 133 > ++++++++++++++++++++++++++++++++++ > 11 files changed, 443 insertions(+), 6 deletions(-) > create mode 100644 arch/arm/dts/exynos5422-odroidxu3.dts > create mode 100644 board/samsung/odroid-xu3/Kconfig > create mode 100644 board/samsung/odroid-xu3/MAINTAINERS > create mode 100644 board/samsung/odroid-xu3/Makefile > create mode 100644 board/samsung/odroid-xu3/odroid-xu3.c > create mode 100644 board/samsung/odroid-xu3/setup.h > create mode 100644 configs/odroid-xu3_defconfig > create mode 100644 include/configs/odroid_xu3.h > > diff --git a/arch/arm/cpu/armv7/exynos/Kconfig > b/arch/arm/cpu/armv7/exynos/Kconfig > index 13dbd95..16c9a0e 100644 > --- a/arch/arm/cpu/armv7/exynos/Kconfig > +++ b/arch/arm/cpu/armv7/exynos/Kconfig > @@ -24,6 +24,10 @@ config TARGET_TRATS2 > config TARGET_ODROID > bool "Exynos4412 Odroid board" > > +config TARGET_ODROID_XU3 > + bool "Exynos5422 Odroid board" > + select OF_CONTROL > + > config TARGET_ARNDALE > bool "Exynos5250 Arndale board" > select SUPPORT_SPL > @@ -65,6 +69,7 @@ source "board/samsung/universal_c210/Kconfig" > source "board/samsung/origen/Kconfig" > source "board/samsung/trats2/Kconfig" > source "board/samsung/odroid/Kconfig" > +source "board/samsung/odroid-xu3/Kconfig" > source "board/samsung/arndale/Kconfig" > source "board/samsung/smdk5250/Kconfig" > source "board/samsung/smdk5420/Kconfig" > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile > index e5846ea..a811b1b 100644 > --- a/arch/arm/dts/Makefile > +++ b/arch/arm/dts/Makefile > @@ -13,7 +13,8 @@ dtb-$(CONFIG_EXYNOS5) += exynos5250-arndale.dtb \ > exynos5250-smdk5250.dtb \ > exynos5420-smdk5420.dtb \ > exynos5420-peach-pit.dtb \ > - exynos5800-peach-pi.dtb > + exynos5800-peach-pi.dtb \ > + exynos5422-odroidxu3.dtb Is it 5422 or 45800? Is there any difference really? > dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \ > tegra20-medcom-wide.dtb \ > tegra20-paz00.dtb \ > diff --git a/arch/arm/dts/exynos5422-odroidxu3.dts > b/arch/arm/dts/exynos5422-odroidxu3.dts > new file mode 100644 > index 0000000..533d88e > --- /dev/null > +++ b/arch/arm/dts/exynos5422-odroidxu3.dts > @@ -0,0 +1,57 @@ > +/* > + * Odroid XU3 device tree source > + * > + * Copyright (c) 2014 Samsung Electronics Co., Ltd. > + * http://www.samsung.com > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +/dts-v1/; > +#include "exynos54xx.dtsi" > + > +/ { > + model = "Odroid XU3 based on EXYNOS5422"; > + compatible = "samsung,odroidxu3", "samsung,exynos5"; > + > + aliases { > + serial0 = "/serial@12C00000"; > + console = "/serial@12C20000"; > + }; > + > + memory { > + device_type = "memory"; > + reg = <0x40000000 0x10000000 > + 0x50000000 0x10000000 > + 0x60000000 0x10000000 > + 0x70000000 0x10000000 > + 0x80000000 0x10000000 > + 0x90000000 0x10000000 > + 0xa0000000 0x10000000 > + 0xb0000000 0xea00000>; > + }; > + > + serial@12C20000 { > + status="okay"; > + }; > + > + mmc@12200000 { > + samsung,bus-width = <8>; > + samsung,timing = <1 3 3>; > + fifoth_val = <0x200f0020>; > + }; > + > + mmc@12210000 { > + status = "disabled"; > + }; > + > + mmc@12220000 { > + samsung,bus-width = <4>; > + samsung,timing = <1 2 3>; > + fifoth_val = <0x200f0020>; > + }; > + > + mmc@12230000 { > + status = "disabled"; > + }; > +}; > diff --git a/board/samsung/odroid-xu3/Kconfig > b/board/samsung/odroid-xu3/Kconfig > new file mode 100644 > index 0000000..6159692 > --- /dev/null > +++ b/board/samsung/odroid-xu3/Kconfig > @@ -0,0 +1,12 @@ > +if TARGET_ODROID_XU3 > + > +config SYS_BOARD > + default "odroid-xu3" > + > +config SYS_VENDOR > + default "samsung" > + > +config SYS_CONFIG_NAME > + default "odroid_xu3" > + > +endif > diff --git a/board/samsung/odroid-xu3/MAINTAINERS > b/board/samsung/odroid-xu3/MAINTAINERS > new file mode 100644 > index 0000000..50cf928 > --- /dev/null > +++ b/board/samsung/odroid-xu3/MAINTAINERS > @@ -0,0 +1,6 @@ > +ODROID-XU3 BOARD > +M: Hyungwon Hwang <human.hw...@samsung.com> > +S: Maintained > +F: board/samsung/odroid-xu3/ > +F: include/configs/odroid_xu3.h > +F: configs/odroid-xu3_defconfig > diff --git a/board/samsung/odroid-xu3/Makefile > b/board/samsung/odroid-xu3/Makefile > new file mode 100644 > index 0000000..85ae5c5 > --- /dev/null > +++ b/board/samsung/odroid-xu3/Makefile > @@ -0,0 +1,7 @@ > +# > +# Copyright (c) 2014 Samsung Electronics Co., Ltd. All rights reserved. > +# > +# SPDX-License-Identifier: GPL-2.0+ > +# > + > +obj-y := odroid-xu3.o > diff --git a/board/samsung/odroid-xu3/odroid-xu3.c > b/board/samsung/odroid-xu3/odroid-xu3.c > new file mode 100644 > index 0000000..8c54842 > --- /dev/null > +++ b/board/samsung/odroid-xu3/odroid-xu3.c > @@ -0,0 +1,122 @@ > +/* > + * Copyright (C) 2014 Samsung Electronics > + * Hyungwon Hwang <human.hw...@samsung.com> > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#include <common.h> > +#include <asm/arch/clock.h> > +#include "setup.h" > + > +DECLARE_GLOBAL_DATA_PTR; > + > +unsigned int get_board_rev(void) > +{ > + return 0; > +} > + > +int exynos_init(void) > +{ > + return 0; > +} > + > +#ifdef CONFIG_BOARD_EARLY_INIT_F > +static int board_clock_init(void) > +{ > + unsigned int set, clr, clr_src_cpu, clr_pll_con0; > + struct exynos5420_clock *clk = (struct exynos5420_clock *) > + samsung_get_base_clock(); This stuff needs to move into SPL - if it works then perhaps hardkernel can do this work. It doesn't make sense to set up the clocks in SPL and then again in U-Boot. At the least this should be commented as a temporary hack, and enable with a CONFIG_EXYNOS_REINIT_CLOCKS option, or something. > + /* > + * CMU_CPU clocks src to MPLL > + * Bit values: 0 ; 1 > + * MUX_APLL_SEL: FIN_PLL ; FOUT_APLL > + * MUX_CORE_SEL: MOUT_APLL ; SCLK_MPLL > + * MUX_HPM_SEL: MOUT_APLL ; SCLK_MPLL_USER_C > + * MUX_MPLL_USER_SEL_C: FIN_PLL ; SCLK_MPLL > + */ > + > + /* Set CMU_CPU clocks src to OSCCLK */ > + clr_src_cpu = MUX_APLL_SEL(1) | MUX_CORE_SEL(1); > + set = MUX_APLL_SEL(0) | MUX_CORE_SEL(1); > + > + clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set); > + > + while (MUX_STAT_CPU_CHANGING(readl(&clk->mux_stat_cpu))) > + continue; > + > + /* Set APLL to 1200MHz */ Why not 1.7GHz? > + clr_pll_con0 = SDIV(7) | PDIV(63) | MDIV(1023) | FSEL(1) | > + PLL_ENABLE(1); > + set = SDIV(0) | PDIV(2) | MDIV(100) | PLL_ENABLE(1); > + > + clrsetbits_le32(&clk->apll_con0, clr_pll_con0, set); > + > + while (!(readl(&clk->apll_con0) & PLL_LOCKED_BIT)) > + continue; > + > + /* Set CMU_CPU clocks src to APLL */ > + set = MUX_APLL_SEL(1) | MUX_CORE_SEL(0); > + clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set); > + > + while (MUX_STAT_CPU_CHANGING(readl(&clk->mux_stat_cpu))) > + continue; > + > + clr = ARM_RATIO(7) | CPUD_RATIO(7) | ATB_RATIO(7) | > + PCLK_DBG_RATIO(7) | APLL_RATIO(7) | ARM2_RATIO(7); > + set = ARM_RATIO(0) | CPUD_RATIO(2) | ATB_RATIO(5) | > + PCLK_DBG_RATIO(5) | APLL_RATIO(0) | ARM2_RATIO(0); > + > + clrsetbits_le32(&clk->div_cpu0, clr, set); > + > + while (readl(&clk->div_stat_cpu0) & DIV_STAT_CPU0_CHANGING) > + continue; > + > + /* Set MPLL to 800MHz */ > + set = SDIV(1) | PDIV(3) | MDIV(200) | PLL_ENABLE(1); > + > + clrsetbits_le32(&clk->mpll_con0, clr_pll_con0, set); > + > + while (!(readl(&clk->mpll_con0) & PLL_LOCKED_BIT)) > + continue; > + > + /* Set CLKMUX_UART src to MPLL */ > + clr = UART0_SEL(7) | UART1_SEL(7) | UART2_SEL(7) | UART3_SEL(7); > + set = UART0_SEL(3) | UART1_SEL(3) | UART2_SEL(3) | UART3_SEL(3); > + > + clrsetbits_le32(&clk->src_peric0, clr, set); > + > + /* Set SCLK_UART to 400 MHz (MPLL / 2) */ > + clr = UART0_RATIO(15) | UART1_RATIO(15) | UART2_RATIO(15) | > + UART3_RATIO(15); > + set = UART0_RATIO(1) | UART1_RATIO(1) | UART2_RATIO(1) | > + UART3_RATIO(1); > + > + clrsetbits_le32(&clk->div_peric0, clr, set); > + > + while (readl(&clk->div_stat_peric0) & DIV_STAT_PERIC0_CHANGING) > + continue; > + > + /* Set CLKMUX_MMC src to MPLL */ > + clr = MUX_MMC0_SEL(7) | MUX_MMC1_SEL(7) | MUX_MMC2_SEL(7); > + set = MUX_MMC0_SEL(3) | MUX_MMC1_SEL(3) | MUX_MMC2_SEL(3); > + > + clrsetbits_le32(&clk->src_fsys, clr, set); > + > + clr = MMC0_RATIO(0x3ff) | MMC1_RATIO(0x3ff) | MMC2_RATIO(0x3ff); > + set = MMC0_RATIO(0) | MMC1_RATIO(0) | MMC2_RATIO(0); > + > + clrsetbits_le32(&clk->div_fsys1, clr, set); > + > + /* Wait for divider ready status */ > + while (readl(&clk->div_stat_fsys1) & DIV_STAT_FSYS1_CHANGING) > + continue; > + > + return 0; > +} > + > +int exynos_early_init_f(void) > +{ > + return board_clock_init(); > +} > +#endif > diff --git a/board/samsung/odroid-xu3/setup.h > b/board/samsung/odroid-xu3/setup.h > new file mode 100644 > index 0000000..143c189 > --- /dev/null > +++ b/board/samsung/odroid-xu3/setup.h > @@ -0,0 +1,95 @@ > +/* > + * (C) Copyright 2014 Samsung Electronics > + * Hyungwon Hwang <human.hw...@samsung.com> > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#ifndef __ODROID_XU3_SETUP__ > +#define __ODROID_XU3_SETUP__ > + > +#define SDIV(x) ((x) & 0x7) > +#define PDIV(x) (((x) & 0x3f) << 8) > +#define MDIV(x) (((x) & 0x3ff) << 16) > +#define FSEL(x) (((x) & 0x1) << 27) > +#define PLL_LOCKED_BIT (0x1 << 29) > +#define PLL_ENABLE(x) (((x) & 0x1) << 31) > + > +/* CLK_SRC_CPU */ > +#define MUX_APLL_SEL(x) ((x) & 0x1) > +#define MUX_CORE_SEL(x) (((x) & 0x1) << 16) > + > +/* CLK_MUX_STAT_CPU */ > +#define APLL_SEL(x) ((x) & 0x7) > +#define CORE_SEL(x) (((x) & 0x7) << 16) > +#define MUX_STAT_CPU_CHANGING(x) !(((x) & APLL_SEL(0)) || \ > + (x) & APLL_SEL(1) || \ > + (x) & CORE_SEL(0) || \ > + (x) & CORE_SEL(1)) > + > +/* CLK_DIV_CPU0 */ > +#define ARM_RATIO(x) ((x) & 0x7) > +#define CPUD_RATIO(x) (((x) & 0x7) << 4) > +#define ATB_RATIO(x) (((x) & 0x7) << 16) > +#define PCLK_DBG_RATIO(x) (((x) & 0x7) << 20) > +#define APLL_RATIO(x) (((x) & 0x7) << 24) > +#define ARM2_RATIO(x) (((x) & 0x7) << 28) > + > +/* CLK_DIV_STAT_CPU0 */ > +#define DIV_CPUD(x) (((x) & 0x1) << 4) > +#define DIV_ATB(x) (((x) & 0x1) << 16) > +#define DIV_PCLK_DBG(x) (((x) & 0x1) << 20) > +#define DIV_APLL(x) (((x) & 0x1) << 24) > +#define DIV_ARM2(x) (((x) & 0x1) << 28) > + > +#define DIV_STAT_CHANGING 0x1 > +#define DIV_STAT_CPU0_CHANGING (DIV_CPUD(DIV_STAT_CHANGING) | \ > + DIV_ATB(DIV_STAT_CHANGING) | \ > + DIV_PCLK_DBG(DIV_STAT_CHANGING) | \ > + DIV_APLL(DIV_STAT_CHANGING) | \ > + DIV_ARM2(DIV_STAT_CHANGING)) > + > +/* Set CLK_SRC_PERIC0 */ > +#define UART0_SEL(x) (((x) & 0xf) << 4) > +#define UART1_SEL(x) (((x) & 0xf) << 8) > +#define UART2_SEL(x) (((x) & 0xf) << 12) > +#define UART3_SEL(x) (((x) & 0xf) << 16) > + > +/* Set CLK_DIV_PERIC0 */ > +#define UART0_RATIO(x) (((x) & 0xf) << 8) > +#define UART1_RATIO(x) (((x) & 0xf) << 12) > +#define UART2_RATIO(x) (((x) & 0xf) << 16) > +#define UART3_RATIO(x) (((x) & 0xf) << 20) > + > +/* Set CLK_DIV_STAT_PERIC0 */ > +#define DIV_UART0(x) ((x) & 0x1) > +#define DIV_UART1(x) (((x) & 0x1) << 4) > +#define DIV_UART2(x) (((x) & 0x1) << 8) > +#define DIV_UART3(x) (((x) & 0x1) << 12) > +#define DIV_UART4(x) (((x) & 0x1) << 16) > + > +#define DIV_STAT_PERIC0_CHANGING (DIV_UART4(DIV_STAT_CHANGING) | \ > + DIV_UART3(DIV_STAT_CHANGING) | \ > + DIV_UART2(DIV_STAT_CHANGING) | \ > + DIV_UART1(DIV_STAT_CHANGING) | \ > + DIV_UART0(DIV_STAT_CHANGING)) > + > +/* CLK_SRC_FSYS */ > +#define MUX_MMC0_SEL(x) (((x) & 0x7) << 8) > +#define MUX_MMC1_SEL(x) (((x) & 0x7) << 12) > +#define MUX_MMC2_SEL(x) (((x) & 0x7) << 16) > + > +/* CLK_DIV_FSYS1 */ > +#define MMC0_RATIO(x) ((x) & 0x3ff) > +#define MMC1_RATIO(x) (((x) & 0x3ff) << 10) > +#define MMC2_RATIO(x) (((x) & 0x3ff) << 20) > + > +#define DIV_MMC0(x) (((x) & 1) << 20) > +#define DIV_MMC1(x) (((x) & 1) << 24) > +#define DIV_MMC2(x) (((x) & 1) << 28) > + > +#define DIV_STAT_FSYS1_CHANGING (DIV_MMC0(DIV_STAT_CHANGING) | \ > + DIV_MMC1(DIV_STAT_CHANGING) | \ > + DIV_MMC2(DIV_STAT_CHANGING)) > + > +#endif > diff --git a/configs/odroid-xu3_defconfig b/configs/odroid-xu3_defconfig > new file mode 100644 > index 0000000..74aa0cf > --- /dev/null > +++ b/configs/odroid-xu3_defconfig > @@ -0,0 +1,4 @@ > +CONFIG_ARM=y > +CONFIG_ARCH_EXYNOS=y > +CONFIG_TARGET_ODROID_XU3=y > +CONFIG_DEFAULT_DEVICE_TREE="exynos5422-odroidxu3" > diff --git a/include/configs/odroid.h b/include/configs/odroid.h > index 807e96b..660b6ae 100644 > --- a/include/configs/odroid.h > +++ b/include/configs/odroid.h > @@ -166,11 +166,6 @@ > "mmcbootpart=1\0" \ > "mmcrootdev=0\0" \ > "mmcrootpart=2\0" \ > - "bootdelay=0\0" \ > - "dfu_alt_system="CONFIG_DFU_ALT \ > - "dfu_alt_info=Please reset the board\0" \ > - "consoleon=set console console=ttySAC1,115200n8; save; reset\0" \ > - "consoleoff=set console console=ram; save; reset\0" \ > "initrdname=uInitrd\0" \ > "initrdaddr=42000000\0" \ > "fdtaddr=40800000\0" > diff --git a/include/configs/odroid_xu3.h b/include/configs/odroid_xu3.h > new file mode 100644 > index 0000000..1d53653 > --- /dev/null > +++ b/include/configs/odroid_xu3.h > @@ -0,0 +1,133 @@ > +/* > + * Copyright (C) 2013 Samsung Electronics > + * Hyungwon Hwang <human.hw...@samsung.com> > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#ifndef __CONFIG_ODROID_XU3_H > +#define __CONFIG_ODROID_XU3_H > + > +#include "exynos5-common.h" Should include exynos5420-common.h. If there are things in there that should not be common, then you could add a patch to move them out. This causes a build warning in I2C. > + > +#define CONFIG_SYS_PROMPT "ODROID-XU3 # " > +#define CONFIG_IDENT_STRING " for ODROID-XU3" > + > +#define CONFIG_BOARD_COMMON > + > +#define CONFIG_SYS_SDRAM_BASE 0x40000000 > +#define CONFIG_SYS_TEXT_BASE 0x43E00000 > + > +/* select serial console configuration */ > +#define CONFIG_SERIAL2 /* use SERIAL 2 */ > + > +#define TZPC_BASE_OFFSET 0x10000 > + > +#define CONFIG_CMD_MMC > +#define CONFIG_CMD_EXT2 > +#define CONFIG_CMD_EXT4 > +#define CONFIG_CMD_FAT > + > +/* > + * FIXME: The number of bank is actually 8. But there is no way to reserver > the > + * last 16 Mib in the last bank now. So I just excluded the last bank > + * temporally. > + */ > +#define CONFIG_NR_DRAM_BANKS 7 > +#define SDRAM_BANK_SIZE (256UL << 20UL) /* 256 MB */ > + > +#define CONFIG_ENV_IS_IN_MMC > + > +#undef CONFIG_ENV_SIZE > +#undef CONFIG_ENV_OFFSET > +#define CONFIG_ENV_SIZE 4096 > +#define CONFIG_ENV_OFFSET (SZ_1K * 1280) /* 1.25 MiB offset */ > + > +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - 0x1000000) > + > +#define CONFIG_BOOTCOMMAND "run autoboot" > +#define CONFIG_DEFAULT_CONSOLE "console=ttySAC2,115200n8\0" > + > +/* > + * For details, refer the documentation: doc/README.odroid > +*/ > +#ifdef CONFIG_EXTRA_ENV_SETTINGS > +#undef CONFIG_EXTRA_ENV_SETTINGS > +#endif > +#define CONFIG_EXTRA_ENV_SETTINGS \ > + "loadkernel=fatload mmc ${mmcbootdev}:${mmcbootpart} ${kerneladdr} " \ > + "${kernelname}\0" \ > + "loadinitrd=fatload mmc ${mmcbootdev}:${mmcbootpart} ${initrdaddr} " \ > + "${initrdname}\0" \ > + "loaddtb=fatload mmc ${mmcbootdev}:${mmcbootpart} ${fdtaddr} " \ > + "${fdtfile}\0" \ > + "check_ramdisk=" \ > + "if run loadinitrd; then " \ > + "setenv initrd_addr ${initrdaddr};" \ > + "else " \ > + "setenv initrd_addr -;" \ > + "fi;\0" \ > + "check_dtb=" \ > + "if run loaddtb; then " \ > + "setenv fdt_addr ${fdtaddr};" \ > + "else " \ > + "setenv fdt_addr;" \ > + "fi;\0" \ > + "kernel_args=" \ > + "setenv bootargs > root=/dev/mmcblk${mmcrootdev}p${mmcrootpart}" \ > + " rootwait ${console} ${opts}\0" \ > + "boot_fit=" \ > + "setenv kerneladdr 0x42000000;" \ > + "setenv kernelname Image.itb;" \ > + "run loadkernel;" \ > + "run kernel_args;" \ > + "bootm ${kerneladdr}#${boardname}\0" \ > + "boot_uimg=" \ > + "setenv kerneladdr 0x40007FC0;" \ > + "setenv kernelname uImage;" \ > + "run check_dtb;" \ > + "run check_ramdisk;" \ > + "run loadkernel;" \ > + "run kernel_args;" \ > + "bootm ${kerneladdr} ${initrd_addr} ${fdt_addr};\0" \ > + "boot_zimg=" \ > + "setenv kerneladdr 0x40007FC0;" \ > + "setenv kernelname zImage;" \ > + "run check_dtb;" \ > + "run check_ramdisk;" \ > + "run loadkernel;" \ > + "run kernel_args;" \ > + "bootz ${kerneladdr} ${initrd_addr} ${fdt_addr};\0" \ > + "autoboot=" \ > + "if test -e mmc 0 Image.itb; then; " \ > + "run boot_fit;" \ > + "elif test -e mmc 0 zImage; then; " \ > + "run boot_zimg;" \ > + "elif test -e mmc 0 uImage; then; " \ > + "run boot_uimg;" \ > + "fi;\0" \ > + "console=" CONFIG_DEFAULT_CONSOLE \ > + "mmcbootdev=0\0" \ > + "mmcbootpart=1\0" \ > + "mmcrootdev=0\0" \ > + "mmcrootpart=2\0" \ > + "bootdelay=0\0" \ > + "dfu_alt_info=Please reset the board\0" \ > + "consoleon=set console console=ttySAC2,115200n8; save; reset\0" \ > + "consoleoff=set console console=ram; save; reset\0" \ > + "initrdname=uInitrd\0" \ > + "initrdaddr=42000000\0" \ > + "fdtaddr=40800000\0" > + > +/* FIXME: MUST BE REMOVED AFTER TMU IS TURNED ON */ > +#undef CONFIG_EXYNOS_TMU > +#undef CONFIG_TMU_CMD_DTT > + > +#ifdef CONFIG_CMD_NET > +#undef CONFIG_CMD_NET > +#undef CONFIG_SMC911X > +#undef CONFIG_CMD_PXE > +#undef CONFIG_MENU > +#endif Why remove net? > + > +#endif /* __CONFIG_H */ > -- > 1.9.1 > > _______________________________________________ > U-Boot mailing list > U-Boot@lists.denx.de > http://lists.denx.de/mailman/listinfo/u-boot Regards, SImon _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot