hi Stany,
The difference is that you print out assertion log.
Reset not supported on this platform
### ERROR ### Please RESET the board ###
You can add show_boot_progress() function in your bsp file to find out
something.
#define CONFIG_SHOW_BOOT_PROGRESS
void show_boot_progress(int progress)
{
printf("Boot reached stage %d\n", progress);
}
On 2016年07月25日 22:12, Ziyuan Xu wrote:
Hi All,
I'm sorry to tell you that I failed to boot linux kernel with the
mainline u-boot on rk3288 board(both evb-rk3288 & fennec-rk3288). It
was stuck in cleanup_before_linux() before jumping to linux, and the
boot_stage_flag is BOOTSTAGE_ID_BOOTM_HANDOFF.
## Current stack ends at 0x7df638b0 * kernel: cmdline image address =
0x02000000
## No init Ramdisk
ramdisk start = 0x00000000, ramdisk end = 0x00000000
## No Flattened Device Tree
Continuing to boot without FDT
Initial value for argc=3
Final value for argc=3
using: ATAGS
## Transferring control to Linux (at address 02000000)...
Starting kernel ...
With the further investigation, it never returnned back from
invalidate_dcache_all(). I mean that I can't reach stage 4 as below.
cleanup_before_linux
==>cleanup_before_linux_select
==>1.disable_interrupts
==>2.dcache_disable
==>3.invalidate_dcache_all
==>4.icache_disable
Debug further, invalidate_dcache_all invalidate all cache one-by-one
which cache type is DATA_ONLY, INSTRUCTION_DATA or UNIFIED. And
invalidate way from one set to another set in order. The problem is
that the PC ran away in invalidate way loop [cache level L1!!!].
I add some serial output code in __v7_flush_dcache_all to figure out
the bog.
I expect:
Print the value of r9 in sequence, e.g 0x7f, 0x7e, 0x7d..... 0x01,
0x00 (hex)
In fact, print the value of r9 in sequence at first, but print
unexpected value afterwards. e.g 0x7f, 0x7e, 0x7d, ..,0x73, 0x40,
0x85,....
ENTRY(__v7_flush_dcache_all)
[snip]
loop1:
mov r9, r7 @ create working copy of max index
loop2:
+ stmfd sp!, {r0}
+ ldr r0, =0xff690000
+ str r9, [r0]
+ ldmfd sp!, {r0}
ARM( orr r11, r10, r4, lsl r5 ) @ factor way and cache
number into r11
THUMB( lsl r6, r4, r5 )
THUMB( orr r11, r10, r6 ) @ factor way and cache
number into r11
ARM( orr r11, r11, r9, lsl r2 ) @ factor index number
into r11
THUMB( lsl r6, r9, r2 )
THUMB( orr r11, r11, r6 ) @ factor index number into r11
mcr p15, 0, r11, c7, c14, 2 @ clean & invalidate by set/way
subs r9, r9, #1 @ decrement the index
bge loop2
subs r4, r4, #1 @ decrement the way
bge loop1
skip:
ENDPROC(__v7_flush_dcache_all)
I don't have the jtag, hence I can't address the current pc. I have no
doubt that if any glitches in __v7_flush_dcache_all, I reviewed
several times, also copy kernel's implement to here. :-( No effect.
A more interesting thing is that Sandy had report it. He and I have
similar problem. Everything work fine after I applied his patches, or
disable dcache(active CONFIG_SYS_DCACHE_OFF).
@Stany, I'm sorry that I disable dcache during hack.. That was a
mistake:-(
@Simon & hieko,
Can you boot linux with the mainline u-boot? have a try?
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
