Dear All,
I add the ISB operation after dcache_disable(), and I can jump to
linux kernel entry.:-)
diff --git a/arch/arm/cpu/armv7/cpu.c b/arch/arm/cpu/armv7/cpu.c
index 6eac5ef..5cc09ba 100644
--- a/arch/arm/cpu/armv7/cpu.c
+++ b/arch/arm/cpu/armv7/cpu.c
@@ -43,6 +43,7 @@ int cleanup_before_linux_select(int flags)
*/
dcache_disable();
v7_outer_cache_disable();
+ ISB;
/*
* After D-cache is flushed and before it is disabled
there may
Sounds crazy. In fact, there is already an 'ISB' operation in set_cr()
which to disable dcache and MMU. But it just tell processor that
memory had change, not real ISB for armv7.
dcache_disable
==>flush_dcache_all()
==>set_cr() disable dcache and MMU.
#define isb() __asm__ __volatile__ ("" : : : "memory")
static inline void set_cr(unsigned int val)
{
if (is_hyp())
asm volatile("mcr p15, 4, %0, c1, c0, 0 @ set CR" :
: "r" (val)
: "cc");
else
asm volatile("mcr p15, 0, %0, c1, c0, 0 @ set CR" :
: "r" (val)
: "cc");
isb();
}
I also find something in ARM cortex-A17 TRM. ==>"Disable the MMU from
the each processor followed by an ISB to ensure the MMU disable
operation is complete, then followed by a DSB to drain previous memory
transactions."
In my humble opinion, maybe instructions tlb had alter, and cause
running away??? I'm not sure about it.
@Sandy, could you have a try with my update?
@Simon, did you hit this glitch? I hope you can help ...:-)
On 2016年07月25日 23:00, Sandy Patterson wrote:
Ah, thanks. Your debugging looks the same as what I've seen from
printf debugging. I'll try to verify though.
On Mon, Jul 25, 2016 at 10:58 AM, Ziyuan Xu <xzy...@rock-chips.com
<mailto:xzy...@rock-chips.com>> wrote:
hi Stany,
The difference is that you print out assertion log.
Reset not supported on this platform
### ERROR ### Please RESET the board ###
You can add show_boot_progress() function in your bsp file to find
out something.
#define CONFIG_SHOW_BOOT_PROGRESS
void show_boot_progress(int progress)
{
printf("Boot reached stage %d\n", progress);
}
On 2016年07月25日 22:12, Ziyuan Xu wrote:
Hi All,
I'm sorry to tell you that I failed to boot linux kernel with
the mainline u-boot on rk3288 board(both evb-rk3288 &
fennec-rk3288). It was stuck in cleanup_before_linux() before
jumping to linux, and the boot_stage_flag is
BOOTSTAGE_ID_BOOTM_HANDOFF.
## Current stack ends at 0x7df638b0 * kernel: cmdline image
address = 0x02000000
## No init Ramdisk
ramdisk start = 0x00000000, ramdisk end = 0x00000000
## No Flattened Device Tree
Continuing to boot without FDT
Initial value for argc=3
Final value for argc=3
using: ATAGS
## Transferring control to Linux (at address 02000000)...
Starting kernel ...
With the further investigation, it never returnned back from
invalidate_dcache_all(). I mean that I can't reach stage 4 as
below.
cleanup_before_linux
==>cleanup_before_linux_select
==>1.disable_interrupts
==>2.dcache_disable
==>3.invalidate_dcache_all
==>4.icache_disable
Debug further, invalidate_dcache_all invalidate all cache
one-by-one which cache type is DATA_ONLY, INSTRUCTION_DATA or
UNIFIED. And invalidate way from one set to another set in
order. The problem is that the PC ran away in invalidate way
loop [cache level L1!!!].
I add some serial output code in __v7_flush_dcache_all to
figure out the bog.
I expect:
Print the value of r9 in sequence, e.g 0x7f, 0x7e, 0x7d.....
0x01, 0x00 (hex)
In fact, print the value of r9 in sequence at first, but print
unexpected value afterwards. e.g 0x7f, 0x7e, 0x7d, ..,0x73,
0x40, 0x85,....
ENTRY(__v7_flush_dcache_all)
[snip]
loop1:
mov r9, r7 @ create working copy of max
index
loop2:
+ stmfd sp!, {r0}
+ ldr r0, =0xff690000
+ str r9, [r0]
+ ldmfd sp!, {r0}
ARM( orr r11, r10, r4, lsl r5 ) @ factor way and
cache number into r11
THUMB( lsl r6, r4, r5 )
THUMB( orr r11, r10, r6 ) @ factor way and
cache number into r11
ARM( orr r11, r11, r9, lsl r2 ) @ factor index
number into r11
THUMB( lsl r6, r9, r2 )
THUMB( orr r11, r11, r6 ) @ factor index
number into r11
mcr p15, 0, r11, c7, c14, 2 @ clean & invalidate
by set/way
subs r9, r9, #1 @ decrement the index
bge loop2
subs r4, r4, #1 @ decrement the way
bge loop1
skip:
ENDPROC(__v7_flush_dcache_all)
I don't have the jtag, hence I can't address the current pc. I
have no doubt that if any glitches in __v7_flush_dcache_all, I
reviewed several times, also copy kernel's implement to here.
:-( No effect.
A more interesting thing is that Sandy had report it. He and I
have similar problem. Everything work fine after I applied his
patches, or disable dcache(active CONFIG_SYS_DCACHE_OFF).
@Stany, I'm sorry that I disable dcache during hack.. That was
a mistake:-(
@Simon & hieko,
Can you boot linux with the mainline u-boot? have a try?
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de <mailto:U-Boot@lists.denx.de>
http://lists.denx.de/mailman/listinfo/u-boot
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot