It can't. Ethernet and USB are both fubar'd using lamobo-r1 on bananapi-r1. Mainly the GMAC delay is different, If you buy one and test it, you will find that they are definitely *not* compatible. Period.
Steve On Sun, Oct 2, 2016 at 10:17 AM, Jagan Teki <jagannadh.t...@gmail.com> wrote: > On Sun, Oct 2, 2016 at 10:06 AM, Stephen Arnold > <stephen.arnol...@gmail.com> wrote: >> From: Steve Arnold <stephen.arnol...@gmail.com> >> >> * needs different GMAC_TX_DELAY than lamobo-r1 (not compatible) >> * tested with 4.8_rc6 b53-mdio and kernel dts switch nodes >> >> Signed-off-by: Stephen Arnold <stephen.arnol...@gmail.com> >> Cc: Ian Campbell <i...@hellion.org.uk> >> Cc: Hans De Goede <hdego...@redhat.com> >> --- >> arch/arm/dts/Makefile | 1 + >> arch/arm/dts/sun7i-a20-bananapi-r1.dts | 321 >> +++++++++++++++++++++++++++++++++ >> configs/Bananapi_R1_defconfig | 19 ++ >> 3 files changed, 341 insertions(+) >> create mode 100644 arch/arm/dts/sun7i-a20-bananapi-r1.dts >> create mode 100644 configs/Bananapi_R1_defconfig >> >> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile >> index 032c5ae..0cbae00 100644 >> --- a/arch/arm/dts/Makefile >> +++ b/arch/arm/dts/Makefile >> @@ -216,6 +216,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \ >> sun7i-a20-ainol-aw1.dtb \ >> sun7i-a20-bananapi.dtb \ >> sun7i-a20-bananapi-m1-plus.dtb \ >> + sun7i-a20-bananapi-r1.dtb \ >> sun7i-a20-bananapro.dtb \ >> sun7i-a20-cubieboard2.dtb \ >> sun7i-a20-cubietruck.dtb \ >> diff --git a/arch/arm/dts/sun7i-a20-bananapi-r1.dts >> b/arch/arm/dts/sun7i-a20-bananapi-r1.dts >> new file mode 100644 >> index 0000000..30a827f >> --- /dev/null >> +++ b/arch/arm/dts/sun7i-a20-bananapi-r1.dts >> @@ -0,0 +1,321 @@ >> +/* >> + * Copyright 2015 Hans de Goede <hdego...@redhat.com> >> + * >> + * Changes copyright 2016 Stephen Arnold <nerd...@gentoo.org> > > Did you copied this dts from somewhere in ML? > >> + * This file is dual-licensed: you can use it either under the terms >> + * of the GPL or the X11 license, at your option. Note that this dual >> + * licensing only applies to this file, and not this project as a >> + * whole. >> + * >> + * a) This file is free software; you can redistribute it and/or >> + * modify it under the terms of the GNU General Public License as >> + * published by the Free Software Foundation; either version 2 of the >> + * License, or (at your option) any later version. >> + * >> + * This file is distributed in the hope that it will be useful, >> + * but WITHOUT ANY WARRANTY; without even the implied warranty of >> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the >> + * GNU General Public License for more details. >> + * >> + * Or, alternatively, >> + * >> + * b) Permission is hereby granted, free of charge, to any person >> + * obtaining a copy of this software and associated documentation >> + * files (the "Software"), to deal in the Software without >> + * restriction, including without limitation the rights to use, >> + * copy, modify, merge, publish, distribute, sublicense, and/or >> + * sell copies of the Software, and to permit persons to whom the >> + * Software is furnished to do so, subject to the following >> + * conditions: >> + * >> + * The above copyright notice and this permission notice shall be >> + * included in all copies or substantial portions of the Software. >> + * >> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, >> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES >> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND >> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT >> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, >> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING >> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR >> + * OTHER DEALINGS IN THE SOFTWARE. >> + */ >> + >> +/dts-v1/; >> +#include "sun7i-a20.dtsi" >> +#include "sunxi-common-regulators.dtsi" >> + >> +#include <dt-bindings/gpio/gpio.h> >> +#include <dt-bindings/interrupt-controller/irq.h> >> +#include <dt-bindings/pinctrl/sun4i-a10.h> >> + >> +/ { >> + model = "Banana Pi BPI-R1"; >> + compatible = "sinovoip,bpi-r1", "allwinner,sun7i-a20"; >> + >> + aliases { >> + serial0 = &uart0; >> + serial1 = &uart2; >> + serial2 = &uart3; >> + serial3 = &uart7; >> + }; >> + >> + chosen { >> + stdout-path = "serial0:115200n8"; >> + }; >> + >> + leds { >> + compatible = "gpio-leds"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&led_pins_bpi_r1>; >> + >> + green { >> + label = "bpi-r1:green:usr"; >> + gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */ >> + linux,default-trigger = "heartbeat"; >> + }; >> + }; >> + >> + reg_gmac_3v3: gmac-3v3 { >> + compatible = "regulator-fixed"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&gmac_power_pin_bpi_r1>; >> + regulator-name = "gmac-3v3"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + startup-delay-us = <100000>; >> + enable-active-high; >> + gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>; /* PH23 */ >> + }; >> + >> +}; >> + >> +&ahci { >> + target-supply = <®_ahci_5v>; >> + status = "okay"; >> +}; >> + >> +&cpu0 { >> + cpu-supply = <®_dcdc2>; >> +}; >> + >> +&ehci0 { >> + status = "okay"; >> +}; >> + >> +&ehci1 { >> + status = "okay"; >> +}; >> + >> +&ohci0 { >> + status = "okay"; >> +}; >> + >> +&ohci1 { >> + status = "okay"; >> +}; >> + >> +&gmac { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&gmac_pins_rgmii_a>; >> + phy = <&phy1>; >> + phy-mode = "rgmii"; >> + phy-supply = <®_gmac_3v3>; >> + status = "okay"; >> + >> + phy1: ethernet-phy@1 { >> + reg = <1>; >> + }; >> +}; >> + >> +&i2c0 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&i2c0_pins_a>; >> + status = "okay"; >> + >> + axp209: pmic@34 { >> + compatible = "x-powers,axp209"; >> + reg = <0x34>; >> + interrupt-parent = <&nmi_intc>; >> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; >> + >> + interrupt-controller; >> + #interrupt-cells = <1>; >> + }; >> +}; >> + >> +#include "axp209.dtsi" >> + >> +&i2c2 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&i2c2_pins_a>; >> + status = "okay"; >> +}; >> + >> +&ir0 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&ir0_rx_pins_a>; >> + status = "okay"; >> +}; >> + >> +&mmc0 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_r1>; >> + vmmc-supply = <®_vcc3v3>; >> + bus-width = <4>; >> + cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ >> + cd-inverted; >> + status = "okay"; >> +}; >> + >> +&otg_sram { >> + status = "okay"; >> +}; >> + >> +&pio { >> + usb0_id_detect_pin: usb0_id_detect_pin@0 { >> + allwinner,pins = "PH4"; >> + allwinner,function = "gpio_in"; >> + allwinner,drive = <SUN4I_PINCTRL_10_MA>; >> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; >> + }; >> + >> + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { >> + allwinner,pins = "PH5"; >> + allwinner,function = "gpio_in"; >> + allwinner,drive = <SUN4I_PINCTRL_10_MA>; >> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; >> + }; >> + >> + usb0_vbus_pin_bpi_r1: usb0_vbus_pin@0 { >> + allwinner,pins = "PB9"; >> + allwinner,function = "gpio_out"; >> + allwinner,drive = <SUN4I_PINCTRL_10_MA>; >> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; >> + }; >> + >> + usb2_vbus_pin_bpi_r1: usb2_vbus_pin@0 { >> + allwinner,pins = "PH3"; >> + allwinner,function = "gpio_out"; >> + allwinner,drive = <SUN4I_PINCTRL_10_MA>; >> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; >> + }; >> + >> + mmc0_cd_pin_bpi_r1: mmc0_cd_pin@0 { >> + allwinner,pins = "PH1"; >> + allwinner,function = "gpio_in"; >> + allwinner,drive = <SUN4I_PINCTRL_10_MA>; >> + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; >> + }; >> + >> + gmac_power_pin_bpi_r1: gmac_power_pin@0 { >> + allwinner,pins = "PH23"; >> + allwinner,function = "gpio_out"; >> + allwinner,drive = <SUN4I_PINCTRL_10_MA>; >> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; >> + }; >> + >> + led_pins_bpi_r1: led_pins@0 { >> + allwinner,pins = "PH24"; >> + allwinner,function = "gpio_out"; >> + allwinner,drive = <SUN4I_PINCTRL_10_MA>; >> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; >> + }; >> +}; >> + >> +®_ahci_5v { >> + status = "okay"; >> +}; >> + >> +®_dcdc2 { >> + regulator-always-on; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1400000>; >> + regulator-name = "vdd-cpu"; >> +}; >> + >> +®_dcdc3 { >> + regulator-always-on; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1400000>; >> + regulator-name = "vdd-int-dll"; >> +}; >> + >> +®_ldo1 { >> + regulator-name = "vdd-rtc"; >> +}; >> + >> +®_ldo2 { >> + regulator-always-on; >> + regulator-min-microvolt = <3000000>; >> + regulator-max-microvolt = <3000000>; >> + regulator-name = "avcc"; >> +}; >> + >> +®_usb0_vbus { >> + pinctrl-0 = <&usb0_vbus_pin_bpi_r1>; >> + gpio = <&pio 1 9 GPIO_ACTIVE_HIGH>; /* PB9 */ >> + status = "okay"; >> +}; >> + >> +®_usb1_vbus { >> + status = "okay"; >> +}; >> + >> +®_usb2_vbus { >> + pinctrl-0 = <&usb2_vbus_pin_bpi_r1>; >> + gpio = <&pio 7 3 GPIO_ACTIVE_HIGH>; /* PH3 */ >> + status = "okay"; >> +}; >> + >> +&spi0 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&spi0_pins_a>, >> + <&spi0_cs0_pins_a>, >> + <&spi0_cs1_pins_a>; >> + status = "okay"; >> +}; >> + >> +&uart0 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&uart0_pins_a>; >> + status = "okay"; >> +}; >> + >> +&uart2 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&uart2_pins_a>; >> + status = "okay"; >> +}; >> + >> +&uart3 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&uart3_pins_b>; >> + status = "okay"; >> +}; >> + >> +&uart7 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&uart7_pins_a>; >> + status = "okay"; >> +}; >> + >> +&usb_otg { >> + dr_mode = "otg"; >> + status = "okay"; >> +}; >> + >> +&usb_power_supply { >> + status = "okay"; >> +}; >> + >> +&usbphy { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&usb0_id_detect_pin>; >> + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ >> + usb0_vbus_power-supply = <&usb_power_supply>; >> + usb0_vbus-supply = <®_usb0_vbus>; >> + usb1_vbus-supply = <®_usb1_vbus>; >> + usb2_vbus-supply = <®_usb2_vbus>; >> + status = "okay"; >> +}; >> diff --git a/configs/Bananapi_R1_defconfig b/configs/Bananapi_R1_defconfig >> new file mode 100644 >> index 0000000..e5341ee >> --- /dev/null >> +++ b/configs/Bananapi_R1_defconfig >> @@ -0,0 +1,19 @@ >> +CONFIG_ARM=y >> +CONFIG_ARCH_SUNXI=y >> +CONFIG_MACH_SUN7I=y >> +CONFIG_DRAM_CLK=432 >> +CONFIG_GMAC_TX_DELAY=3 >> +CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-bananapi-r1" >> +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set >> +CONFIG_SPL=y >> +CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPH(23),AHCI,USB_EHCI" >> +# CONFIG_CMD_IMLS is not set >> +# CONFIG_CMD_FLASH is not set >> +# CONFIG_CMD_FPGA is not set >> +CONFIG_DM_ETH=y >> +CONFIG_PHYLIB=y >> +# CONFIG_RTL8211X_PHY_FORCE_MASTER=y >> +CONFIG_ETH_DESIGNWARE=y >> +CONFIG_DM_SERIAL=y >> +CONFIG_USB=y >> +CONFIG_DM_USB=y > > Better use the existing Bananapi_defconfig,because most of the configs > are redundant. > > thanks! > -- > Jagan Teki > Free Software Engineer | www.openedev.com > U-Boot, Linux | Upstream Maintainer > Hyderabad, India. _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot