On 07/10/2016 16:59, Jagan Teki wrote: > Hi Stefano, > > On Wed, Oct 5, 2016 at 2:17 AM, Jagan Teki <jt...@openedev.com> wrote: >> From: Jagan Teki <ja...@amarulasolutions.com> >> >> This series supports Engicam i.CoreM6 QDL modules on top of u-boot-imx/master >> and test on the respective starter kits as well. >> >> Tested both MMC and NAND boot. >> >> Changes for v6: >> - Rebase to u-boot-imx/master >> - Move few SPL configs to defconfigs >> >> Changes for v5: >> - Add NAND support >> >> Changes for v4: >> - Add 'net: Kconfig: Add FEC_MXC entry' patch >> - Updated ENV configs along with comments >> - Restructured configs for more readability >> - Add CONFIG_ENV_OVERWRITE >> - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig >> >> Changes for v3: >> - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" >> patch >> - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch >> - Add minimal devicetree support for Engicam i.CoreM6 QDL >> - Add is_mx6dl() >> - Add is_mx6solo() >> - Use is_mx6dq() >> - Add last commit sha1 and header in pull devicetree files from Linux >> >> Changes for v2: >> - Make static to local iomux structure in board file >> - Corrected rowaddr in mx6_ddr3_cfg >> - Used imx_ddr_size >> - Add FEC support and tested the same >> - Add DM_GPIO, DM_MMC support >> - Add pinctrl support >> - Add devicetree support >> >> Jagan Teki (21): >> serial: Kconfig: Add MXC_UART entry >> thermal: Kconfig: Add IMX_THERMAL entry >> Kconfig: Add DEFAULT_FDT_FILE entry >> arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support >> net: Kconfig: Add FEC_MXC entry >> imx6: icorem6: Add ENET support >> imx: s/docs\/README.imximage/doc\/README.imximage/g >> arm: dts: Add devicetree for i.MX6DL >> arm: dts: Add devicetree for i.MX6DQL >> arm: dts: imx6dl: Add pinctrl defines >> dt-bindings: clock: imx6qdl: Add clock defines >> arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo >> imx6q: icorem6: Enable pinctrl driver >> engicam: icorem6: Add DM_GPIO, DM_MMC support >> arm: dts: Add devicetree for i.MX6Q >> arm: dts: imx6q: Add pinctrl defines >> arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual >> mtd: nand: Kconfig: Add NAND_MXS entry >> imx6: icorem6: Add NAND support >> imx6: icorem6: Enable MTD device support >> imx6: icorem6: Add default mtd nand partition table > > All look fine on u-boot-imx/master, please apply
It does not look so fine - I still get the issue with CONFIG_DEFAULT_FDT_FILE, and this generates warning on several file. If you want check, you ca try to build ge_b650v3 (just because I am testing this, but many boards report this warning). For example: w+include/configs/zc5601.h:17:0: warning: "CONFIG_DEFAULT_FDT_FILE" redefined [enabled by default] w+include/generated/autoconf.h:16:0: note: this is the location of the previous definition Can you check it, please ? Best regards, Stefano Babic -- ===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sba...@denx.de ===================================================================== _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot