Hi, I got also somme issue with my QSPI on CycmoneV and u-boot 2017.07 I cherry-picked commits from Jason Rush : b90ce1c29023abe730d2b4174294bdc09acef3e0 836a0278476be94c95ff084f81c2302fc5c0265c b0eac7e0d1e4817388543b58d30b322d0bac49a8
Also i forgot to put the "u-boot,dm-pre-reloc;" in my device tree in the qspi node. Now my QSPI is working fine except the sf unlock / lock I have remove the "clear BP# bits" in the mtd/spi/spi_flash.c Hope this can help you Regards, Clement 2017-09-06 8:10 GMT+02:00 Hannes Schmelzer <han...@schmelzer.or.at>: > Hi Jagan, > > > On 09/04/2017 08:22 AM, Hannes Schmelzer wrote: >> >> "U-Boot" <u-boot-boun...@lists.denx.de> schrieb am 01.09.2017 16:39:03: >> <han...@schmelzer.or.at> wrote: >>>> >>>> Hi Eldor, >>>> >>>> just found your post in the mailinglist. >>>> >>>> https://lists.denx.de/pipermail/u-boot/2016-December/276491.html >>>> >>>> Reason why i'm searched there is, that i've now excactly same problem >> >> as >>>> >>>> you. >>> >>> Can you give some details, issue came-up while 'sf probe' or 'sf read' ? >> >> Hi Jagan, >> please have a look into the weblink to the denx mailing list server. >> I have basically same trouble as eldor reported the days ago. >> >> A simple 'sf probe' ends up in a >> ### ERROR ### Please RESET the board ### >> Interesting detail is, that the information about the flash (type, size, >> ...) is printed out quite before the "hang". >> >> On wednesday i have the next time-slot to access the socfpga devkit board. >> So i could bring in more details if necessary. > > as told few days ago, i've now again access to my socfpga devkit board. > Here comes the console output: > > --- > U-Boot SPL 2017.09-rc4-00023-g84a4206 (Sep 06 2017 - 08:02:35) > /home/schmelzerh/work/u-boot/drivers/ddr/altera/sequencer.c: Preparing to > start memory calibration > /home/schmelzerh/work/u-boot/drivers/ddr/altera/sequencer.c: CALIBRATION > PASSED > /home/schmelzerh/work/u-boot/drivers/ddr/altera/sequencer.c: Calibration > complete > Trying to boot from MMC1 > spl: partition error > > > U-Boot 2017.09-rc4-00023-g84a4206 (Sep 06 2017 - 08:02:35 +0200) > > CPU: Altera SoCFPGA Platform > FPGA: Altera Cyclone V, SE/A6 or SX/C6 or ST/D6, version 0x0 > BOOT: SD/MMC Internal Transceiver (3.0V) > Watchdog enabled > I2C: ready > DRAM: 1 GiB > MMC: dwmmc0@ff704000: 0 > *** Warning - bad CRC, using default environment > > In: serial > Out: serial > Err: serial > Model: Altera SOCFPGA Cyclone V SoC Development Kit > Net: > Error: ethernet@ff702000 address not set. > No ethernet found. > Hit any key to stop autoboot: 0 > => sf probe > SF: Detected n25q512 with page size 256 Bytes, erase size 64 KiB, total 64 > MiB > ### ERROR ### Please RESET the board ### > ---- > > Afterwards the board does some reset (about 20sec. later). > > > cheers, > Hannes > _______________________________________________ > U-Boot mailing list > U-Boot@lists.denx.de > https://lists.denx.de/listinfo/u-boot _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot