On Tue, Jun 5, 2018 at 11:17 AM, Vasily Khoruzhick <anars...@gmail.com> wrote: > On Mon, Jun 4, 2018 at 10:38 PM, Vasily Khoruzhick <anars...@gmail.com> wrote: >>> This wont depend with this phy driver, better check the host driver >>> and dts nodes which you're using. >> >> It starts to work if I enable ehci0 and ohci0 in sun50i-a64-pine64.dts >> - but note that internal hub in Pinebook is connected to ehci1/ohci1, >> not ehci0/ohci0. >> Can you try disabling ehci0/ohci0 and check whether the other >> controller works for you? > > So it works only with all of ehci0, ehci1, ohci0, ohci1 present in > dts. ehci0/ohci0 or ehci1/ohci1 alone won't work.
Don't assume the things, here BPI-M64 without ehci0 and ohci0 Allwinner mUSB OTG (Peripheral) Net: Warning: usb_ether using MAC address from ROM eth0: usb_ether starting USB... USB0: USB EHCI 0.00 USB1: USB OHCI 0.0 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 0 => => mmc dev 1 switch to partitions #0, OK mmc1(part 0) is current device => fastboot 1 musb-hdrc: peripheral reset irq lost! ** Unrecognized filesystem type ** Starting download of 32768 bytes downloading of 32768 bytes finished Flashing Raw Image ........ wrote 32768 bytes to 'loader1' ** Unrecognized filesystem type ** Starting download of 595352 bytes .... downloading of 595352 bytes finished Flashing Raw Image ........ wrote 595456 bytes to 'loader2' => U-Boot SPL 2018.05-00710-gb1f2b72e39-dirty (Jun 05 2018 - 11:14:11 +0530) DRAM: 2048 MiB Trying to boot from MMC2 NOTICE: BL3-1: Running on A64/H64 (1689) in SRAM A2 (@0x44000) NOTICE: Configuring SPC Controller NOTICE: BL3-1: v1.0(debug):ce95c91d NOTICE: BL3-1: Built : 11:56:38, Mar 23 2018 NOTICE: DT: sun50i-a64-bananapi-m64 INFO: Configuring AXP PMIC INFO: PMIC: DRAM voltage: 1.50V INFO: PMIC: setup successful NOTICE: SCPI: dummy stub handler, implementation level: 000000 INFO: BL3-1: Initializing runtime services INFO: BL3-1: Preparing for EL3 exit to normal world INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9 U-Boot 2018.05-00710-gb1f2b72e39-dirty (Jun 05 2018 - 11:14:11 +0530) Allwinner Technology CPU: Allwinner A64 (SUN50I) Model: BananaPi-M64 DRAM: 2 GiB MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1 Loading Environment from FAT... *** Warning - bad CRC, using default environment Failed (-5) In: serial Out: serial Err: serial Allwinner mUSB OTG (Peripheral) Net: Warning: usb_ether using MAC address from ROM eth0: usb_ether starting USB... USB0: USB EHCI 0.00 USB1: USB OHCI 0.0 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 0 => usb info 1: Hub, USB Revision 2.0 - u-boot EHCI Host Controller - Class: Hub - PacketSize: 64 Configurations: 1 - Vendor: 0x0000 Product 0x0000 Version 1.0 Configuration: 1 - Interfaces: 1 Self Powered 0mA Interface: 0 - Alternate Setting 0, Endpoints: 1 - Class Hub - Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms And A64-Relic has only ehci0 and ohci0 no ehci1 and ohci1, better to debug it from your side, what went wrong. Jagan. _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot