I put the printf you asked for in sd_init_card, right after the for loop. Here's the output:
With #define CONFIG_ATMEL_MCI1 1 U-Boot> mmc init 0 mmc: setting clock 150000 Hz, block size 512 mmc: clock 150000 too low; setting CLKDIV to 255 mmc: CMD0 0x0 (flags 0x0) mmc: status 0x0c000025 mmc: CMD0 0x0 (flags 0x100) mmc: status 0x0c000025 mmc: CMD55 0x0 (flags 0x1040) mmc: status 0x0c000025 mmc: response: 00000000 HJS: MMCI_CR = 0 HJS: sd_init_card() mmc_acmd after for loop. ret: -19, resp[0] = 0x6B200020 mmc: CMD0 0x0 (flags 0x0) mmc: status 0x0c000025 mmc: CMD0 0x0 (flags 0x100) mmc: status 0x0c000025 mmc: CMD1 0x100000 (flags 0x841) mmc: status 0x0c000025 mmc: response: 00000000 ...This keeps going for a while and at the end... mmc: CMD1 0x100000 (flags 0x841) mmc: status 0x0c000025 mmc: response: 00000000 No MMC card found With #define CONFIG_ATMEL_MCI1 0 U-Boot> mmc init 0 mmc: setting clock 150000 Hz, block size 512 mmc: clock 150000 too low; setting CLKDIV to 255 mmc: CMD0 0x0 (flags 0x0) mmc: status 0x0c000025 mmc: CMD0 0x0 (flags 0x100) mmc: status 0x0c000025 mmc: CMD55 0x0 (flags 0x1040) mmc: status 0x0c000025 mmc: response: 00000000 HJS: MMCI_CR = 0 HJS: sd_init_card() mmc_acmd after for loop. ret: -19, resp[0] = 0x6B200020 mmc: CMD0 0x0 (flags 0x0) mmc: status 0x0c000025 mmc: CMD0 0x0 (flags 0x100) mmc: status 0x0c000025 mmc: CMD1 0x100000 (flags 0x841) mmc: status 0x0c000025 mmc: response: 00000000 mmc: CMD1 0x100000 (flags 0x841) mmc: status 0x0c000025 mmc: response: 00000000 mmc: CMD1 0x100000 (flags 0x841) mmc: status 0x0c000025 mmc: response: 00000000 mmc: CMD1 0x100000 (flags 0x841) mmc: status 0x0c000025 mmc: response: 00000000 mmc: CMD1 0x100000 (flags 0x841) mmc: status 0x0c000025 mmc: response: 00000000 ...This keeps going for a while and at the end... mmc: CMD1 0x100000 (flags 0x841) mmc: status 0x0c000025 mmc: response: 00000000 No MMC card found If i take out the #define CONFIG_ATMEL_MCI1 U-Boot> mmc init 0 mmc: setting clock 150000 Hz, block size 512 mmc: clock 150000 too low; setting CLKDIV to 255 mmc: CMD0 0x0 (flags 0x0) mmc: status 0x0c000025 mmc: CMD0 0x0 (flags 0x100) mmc: status 0x0c000025 mmc: CMD55 0x0 (flags 0x1040) mmc: status 0x0c000025 mmc: response: 00000120 mmc: CMD41 0x100000 (flags 0x41) mmc: status 0x0c040025 mmc: response: 00ff8000 mmc: CMD55 0x0 (flags 0x1040) mmc: status 0x0c000025 mmc: response: 00000120 mmc: CMD41 0x100000 (flags 0x41) mmc: status 0x0c040025 mmc: response: 00ff8000 ... Goes on for a while... HJS: MMCI_CR = 0 HJS: sd_init_card() mmc_acmd for loop ret: -110, resp[0] = 0x00FF8000 mmc: CMD0 0x0 (flags 0x0) mmc: status 0x0c000025 mmc: CMD0 0x0 (flags 0x100) mmc: status 0x0c000025 mmc: CMD1 0x100000 (flags 0x841) mmc: status 0x0c100025 mmc: command 1 failed (status: 0x0c100025) HJS: error_flags: 0x005B0000, status & error_flags: 0x00100000 HJS: mmc_init_card() ret = -5 HJS: mmc_init_card failed No MMC card found In all of them I used the slot J6. I tried it with J5 too but it did the same thing. On Tue, Mar 16, 2010 at 4:36 PM, Albin Tonnerre < albin.tonne...@free-electrons.com> wrote: > On Tue, 16 Mar 2010 08:30 -0400, Henry Súcart wrote : > > Here's the command I'm using and the output. I put a debugging statement > in > > sd_init_card() after the for loop (HJS:). > > > > U-Boot> mmc init 0 > > mmc: clock 150000 too low; setting CLKDIV to 255 > > HJS: sd_init_card() mmc_acmd for loop finished. ret = -19, resp[0] = > > 0x6B200020 > > No MMC card found > > Err, well, that's weird. I have to admit I can't even guess whether it's > trying to read the right slot. Could you please: > > 1/ add a #define DEBUG at the top of drivers/mmc/atmel_mci.c > 2/ get the output of mmc init (0 or 1 doesn't matter) for both > CONFIG_ATMEL_MCI1 > and !CONFIG_ATMEL_MCI1 (with the SD card staying in the same slot, of > course) > 3/ In the process, add a debug printf in the mci driver displaying the > value of > MMCI_CR (you'd get that by calling mmci_readl(CR)) > > I'm sorry I can't help you further. Unfortunately I don't own such > hardware, and > this kind of thing is rather hard to debug remotely. > > Regards, > -- > Albin Tonnerre, Free Electrons > Kernel, drivers and embedded Linux development, > consulting, training and support. > http://free-electrons.com >
_______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot