On Mon, Apr 22, 2019 at 9:00 PM Peng Fan <peng....@nxp.com> wrote: > > Hi Fabio > > > Subject: Booting MX6 via Serial Download after DM conversion > > > > Hi, > > > > Has anyone managed to boot i.MX6 via serial download protocol after the > > conversion to DM? >
I 'think' the DM conversion requires the USB Driver to be defined as UCLASS_USB_GADGET_GENERIC in order to be used as a peripheral. I have been following one of the TI boards [1] who's USB Driver has a bind tool that go through the device tree and looks to see if the "dr_mode" entry and then binds the appropriate driver (either HOST or GADGET). I started a conversion on this, so I have a patch I can sent to people, but I haven't gotten the GADGET side working, but I have a binder function that then loads the host driver when "dr_mode" is set to host. I haven't had a lot of time to try and figure out the GADGET side of things yet. If someone wants me to send the a patch for what I have so far, I can do that, but it only supports host mode. I am fairly certain all gadget devices are broken on i.MX6 with DM_USB enabled, so in SPL, I had to disable DM_USB in order to maintain the SDP tool compatibility in SPL. [1] - http://git.denx.de/?p=u-boot.git;a=commitdiff;h=7d98dbcc3dc8f1b93676d0953f3bee0db3796eb0 adam > Include Abel who did the conversion. > > > > > On a mx6sabresd I can no longer boot via SDP running 2019.04: > > > > After running 'sudo ./imx_usb SPL' I get: > > Honestly I am not familiar with imx_usb, we use mfgtool previously and not > uuu tool. > Would you share where to download imx_usb and any doc, > Then we will debug this issue. > > Thanks, > Peng. > > > > > U-Boot SPL 2019.04 (Apr 22 2019 - 19:45:46 -0300) Trying to boot from USB > > SDP > > SDP: initialize... > > SDP: handle requests.. > > > > Then I load the u-boot-dtb.img binary and the following error is seen: > > > > $ sudo ./imx_usb u-boot-dtb.img > > config file </usr/etc/imx-loader.d//imx_usb.conf> > > vid=0x066f pid=0x3780 file_name=mx23_usb_work.conf > > vid=0x15a2 pid=0x004f file_name=mx28_usb_work.conf > > vid=0x15a2 pid=0x0052 file_name=mx50_usb_work.conf > > vid=0x15a2 pid=0x0054 file_name=mx6_usb_work.conf > > vid=0x15a2 pid=0x0061 file_name=mx6_usb_work.conf > > vid=0x15a2 pid=0x0063 file_name=mx6_usb_work.conf > > vid=0x15a2 pid=0x0071 file_name=mx6_usb_work.conf > > vid=0x15a2 pid=0x007d file_name=mx6_usb_work.conf > > vid=0x15a2 pid=0x0080 file_name=mx6_usb_work.conf > > vid=0x1fc9 pid=0x0128 file_name=mx6_usb_work.conf > > vid=0x15a2 pid=0x0076 file_name=mx7_usb_work.conf > > vid=0x1fc9 pid=0x0126 file_name=mx7ulp_usb_work.conf > > vid=0x15a2 pid=0x0041 file_name=mx51_usb_work.conf > > vid=0x15a2 pid=0x004e file_name=mx53_usb_work.conf > > vid=0x15a2 pid=0x006a file_name=vybrid_usb_work.conf vid=0x066f > > pid=0x37ff file_name=linux_gadget.conf > > vid=0x1b67 pid=0x4fff file_name=mx6_usb_sdp_spl.conf > > vid=0x0525 pid=0xb4a4 file_name=mx6_usb_sdp_spl.conf > > vid=0x1fc9 pid=0x012b file_name=mx8mq_usb_work.conf config file > > </usr/etc/imx-loader.d//mx6_usb_sdp_spl.conf> > > parse /usr/etc/imx-loader.d//mx6_usb_sdp_spl.conf > > Trying to open device vid=0x0525 pid=0xb4a4 Interface 0 claimed HAB > > security state: development mode (0x56787856) == work item filename > > u-boot-dtb.img load_size 0 bytes load_addr 0x00000000 dcd 1 clear_dcd 0 > > plug 1 jump_mode 3 jump_addr 0x00000000 == end work item header not > > found 8400:2e77d044, 4000 do_download failed, err=-22 HAB security state: > > development mode (0x56787856) > > > > With 2019.01 (prior to DM conversion) I can boot via SDP just fine. > > > > Does anyone have any suggestions? > > > > Thanks, > > > > Fabio Estevam _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
