Hello!
On Wednesday 26 August 2020 09:30:11 Andre Heider wrote:
> Pali,
>
> thank you for all these espressobin fixes, much appreciated!
>
> This isn't directly related to the patch I'm replying to, but since you seem
> to be syncing down- with upstream:
>
> Upstream u-boot doesn't detect my sata ssd ("SATA link 0 timeout"), nor is
Could you try following Marvell SATA/AHCI patch?
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/2c1571432e4fd298be0236b53511f415bbdd21ac
> it able to run debian's kernel (hangs after "Starting kernel"). Both work
> with armbian's downstream flash-image.bin.
>
> I'm using the espressobin v1 with these patches from the list on top of
Do you really have espressobin v1? I saw hw schemas and diagrams only
for V3, V4, V5 and V7. And I tested only V5 as I do not have any other
revisions.
> 2020.07:
> arm64: a37xx: pci: Depends on DM_GPIO
> arm: mvebu: Espressobin: Update README.marvell file
> arm: mvebu: Espressobin: Define console env
> arm: mvebu: Espressobin: Define fdt_addr and kernel_addr env aliases
> arm: mvebu: Espressobin: Change default loadaddr
> arm: mvebu: Espressobin: Move env load addresses
> arm: mvebu: Espressobin: Setup MTD partitions when booting kernel
> arm: mvebu: Espressobin: Make SPI env offset compatible with Marvell's
> U-Boot
> arm: dts: a37x0: enable sd card support on espressobin
> mmc: xenon: set signal voltage and max base clock
> arm64: a37xx: pci: Assert PERST# signal when unloading driver
> arm64: a37xx: pci: Make PCIe Reset GPIO DT compatible with Linux kernel DT
> arm64: dts: armada-3720-espressobin: fix COMPHY nodes
> arm: mvebu: Espressobin: Enable CONFIG_MVNETA
> arm: mvebu: Espressobin: Disallow forwarding packets between wan and lan
> ports
>
> Bootlog:
>
> TIM-1.0
> WTMI-devel-18.12.1-
> WTMI: system early-init
> CPU VDD voltage default value: 1.108V
> NOTICE: Booting Trusted Firmware
> NOTICE: BL1: v2.3(): (Marvell-devel-18.12.0)
> NOTICE: BL1: Built : 06:12:46, Aug 26 2020
> NOTICE: BL1: Booting BL2
> NOTICE: BL2: v2.3(): (Marvell-devel-18.12.0)
> NOTICE: BL2: Built : 06:12:46, Aug 26 2020
> NOTICE: BL1: Booting BL31
> NOTICE: BL31: v2.3(): (Marvell-devel-18.12.0)
> NOTICE: BL31: Built : 06:12:46
>
> U-Boot 2020.07 (Aug 26 2020 - 06:12:46 +0000)
>
> DRAM: 1 GiB
> Comphy-0: USB3_HOST0 5 Gbps
> Comphy-1: PEX0 2.5 Gbps
> Comphy-2: SATA0 5 Gbps
> SATA link 0 timeout.
> AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
> flags: ncq led only pmp fbss pio slum part sxs
> PCIE-0: Link up
> MMC: sdhci@d0000: 0
> Loading Environment from SPI Flash... SF: Detected w25q32dw with page size
> 256 Bytes, erase size 4 KiB, total 4 MiB
> OK
> Model: Marvell Armada 3720 Community Board ESPRESSOBin
> Net: eth0: neta@30000
> Hit any key to stop autoboot: 0
> MMC Device 1 not found
> no mmc device at slot 1
> switch to partitions #0, OK
> mmc0 is current device
> Scanning mmc 0:1...
> Found U-Boot script /boot.scr
> 2250 bytes read in 12 ms (182.6 KiB/s)
> ## Executing script at 06d00000
> 22079344 bytes read in 1219 ms (17.3 MiB/s)
> 10671 bytes read in 24 ms (433.6 KiB/s)
> 27689238 bytes read in 1555 ms (17 MiB/s)
> Booting Debian 5.7.0-0.bpo.2-arm64 from mmc 0:1...
> ## Flattened Device Tree blob at 06f00000
> Booting using the fdt blob at 0x6f00000
> Loading Ramdisk to 3e0be000, end 3fb26116 ... OK
> Loading Device Tree to 000000003e0b8000, end 000000003e0bd9ae ... OK
>
> Starting kernel ...
> <hangs here>
Can you write which commands you have run to load & boot kernel?
What are command line arguments for kernel?
Also have you reset env variables to default?
