On Fri, 17 Dec 2021 20:23:27 -0800 Tony Dinh <mibo...@gmail.com> wrote:
Hi, > Add DTS files for Pogoplug V4 board is there any reason you didn't take the kirkwood-pogoplug-series-4.dts file from the Linux tree? That is the same device, isn't it? Tom will ask you about the upstream status anyway... Cheers, Andre > > Signed-off-by: Tony Dinh <mibo...@gmail.com> > --- > > arch/arm/dts/Makefile | 1 + > arch/arm/dts/kirkwood-pogoplug_v4.dts | 145 ++++++++++++++++++++++++++ > 2 files changed, 146 insertions(+) > create mode 100644 arch/arm/dts/kirkwood-pogoplug_v4.dts > > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile > index 7f622fedbd..716c6c0ed2 100644 > --- a/arch/arm/dts/Makefile > +++ b/arch/arm/dts/Makefile > @@ -68,6 +68,7 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += \ > kirkwood-openrd-client.dtb \ > kirkwood-openrd-ultimate.dtb \ > kirkwood-pogo_e02.dtb \ > + kirkwood-pogoplug_v4.dtb \ > kirkwood-sheevaplug.dtb > > dtb-$(CONFIG_MACH_S900) += \ > diff --git a/arch/arm/dts/kirkwood-pogoplug_v4.dts > b/arch/arm/dts/kirkwood-pogoplug_v4.dts > new file mode 100644 > index 0000000000..b4754f600e > --- /dev/null > +++ b/arch/arm/dts/kirkwood-pogoplug_v4.dts > @@ -0,0 +1,145 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright (C) 2014-2021 Tony Dinh <mibo...@gmail.com> > + * > + * Device tree file for the Pogoplug V4/Mobile > + * > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6192.dtsi" > + > +/ { > + model = "Pogoplug v4"; > + compatible = "cloudengines,pogoplug-v4", "cloudengines,pogoplug-mobile", > + "marvell,kirkwood-88f6192", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200"; > + stdout-path = &uart0; > + }; > + > + ocp@f1000000 { > + pinctrl: pin-controller@10000 { > + pmx_led_green: pmx-led-green { > + marvell,pins = "mpp22"; > + marvell,function = "gpio"; > + }; > + pmx_led_red: pmx-led-red { > + marvell,pins = "mpp24"; > + marvell,function = "gpio"; > + }; > + pmx_button_eject: pmx-button-eject { > + marvell,pins = "mpp29"; > + marvell,function = "gpio"; > + }; > + }; > + > + serial@12000 { > + status = "ok"; > + }; > + > + sata@80000 { > + status = "okay"; > + nr-ports = <2>; > + }; > + > + mvsdio@90000 { > + pinctrl-0 = <&pmx_sdio>; > + pinctrl-names = "default"; > + status = "okay"; > + cd-gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>; > + /* No WP GPIO */ > + }; > + }; > + > + gpio-leds { > + compatible = "gpio-leds"; > + pinctrl-0 = <&pmx_led_red &pmx_led_green>; > + pinctrl-names = "default"; > + > + health { > + label = "status:green:health"; > + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; > + default-state = "keep"; > + }; > + fault { > + label = "status:red:fault"; > + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + gpio_keys { > + compatible = "gpio-keys"; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-0 = <&pmx_button_eject>; > + pinctrl-names = "default"; > + > + button@1 { > + label = "Eject Button"; > + linux,code = <KEY_EJECTCD>; > + gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; > + }; > + }; > + > +}; > + > +&nand { > + status = "okay"; > + > + partition@0 { > + label = "u-boot"; > + reg = <0x0000000 0x200000>; > + }; > + > + partition@200000 { > + label = "uImage"; > + reg = <0x200000 0x300000>; > + }; > + > + partition@500000 { > + label = "uImage2"; > + reg = <0x500000 0x300000>; > + }; > + > + partition@800000 { > + label = "failsafe"; > + reg = <0x800000 0x800000>; > + }; > + > + partition@1000000 { > + label = "root"; > + reg = <0x1000000 0x7000000>; > + }; > +}; > + > +&mdio { > + status = "okay"; > + > + ethphy0: ethernet-phy@0 { > + reg = <0>; > + }; > +}; > + > +ð0 { > + status = "okay"; > + ethernet0-port@0 { > + phy-handle = <ðphy0>; > + }; > +}; > + > +&pciec { > + status = "okay"; > +}; > + > +&pcie0 { > + status = "okay"; > +};