From: Quentin Schulz <quentin.sch...@theobroma-systems.com> On Haikou devkit, it is possible to disable eMMC and SPI-NOR to force booting from SD card or USB via rkdeveloptool by toggling a switch. This switch needs to be overridden in software to be able to access eMMC and SPI-NOR once the device has booted from SD Card. Puma SoM can override this pin via gpio3_d5.
Until now, fixed regulator device was abused to model this, but since there's now support for GPIO hogs, let's use it. Since we want to be able to boot the SPL from SD Card but give it the ability to load U-Boot proper from a fallback medium such as eMMC and SPI-NOR, SPL support for GPIO hogs needs to be enabled too. Support for other kinds of regulators are not needed anymore, so let's disable them. Cc: Quentin Schulz <foss+ub...@0leil.net> Signed-off-by: Quentin Schulz <quentin.sch...@theobroma-systems.com> --- Depends on https://lore.kernel.org/u-boot/20220712154422.265925-2-foss+ub...@0leil.net/ arch/arm/dts/rk3399-puma-haikou-u-boot.dtsi | 32 +++++++++------------ configs/puma-rk3399_defconfig | 5 ++-- 2 files changed, 16 insertions(+), 21 deletions(-) diff --git a/arch/arm/dts/rk3399-puma-haikou-u-boot.dtsi b/arch/arm/dts/rk3399-puma-haikou-u-boot.dtsi index e0476ab25c..b9b6ac3f6c 100644 --- a/arch/arm/dts/rk3399-puma-haikou-u-boot.dtsi +++ b/arch/arm/dts/rk3399-puma-haikou-u-boot.dtsi @@ -31,24 +31,6 @@ spi5 = &spi5; }; - /* - * The Qseven BIOS_DISABLE signal on the RK3399-Q7 keeps the on-module - * eMMC and SPI flash powered-down initially (in fact it keeps the - * reset signal asserted). Even though it is an enable signal, we - * model this as a regulator. - */ - bios_enable: bios_enable { - compatible = "regulator-fixed"; - u-boot,dm-pre-reloc; - regulator-name = "bios_enable"; - enable-active-high; - gpio = <&gpio3 RK_PD5 GPIO_ACTIVE_LOW>; - regulator-always-on; - regulator-boot-on; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - vdd_log: vdd-log { compatible = "pwm-regulator"; pwms = <&pwm2 0 25000 1>; @@ -68,6 +50,20 @@ &gpio3 { u-boot,dm-pre-reloc; + + /* + * The Qseven BIOS_DISABLE signal on the RK3399-Q7 keeps the on-module + * eMMC and SPI flash powered-down initially (in fact it keeps the + * reset signal asserted). BIOS_DISABLE_OVERRIDE pin allows to re-enable + * eMMC and SPI after the SPL has been booted from SD Card. + */ + bios_disable_override { + u-boot,dm-pre-reloc; + gpios = <RK_PD5 GPIO_ACTIVE_LOW>; + output-high; + line-name = "bios_disable_override"; + gpio-hog; + }; }; &norflash { diff --git a/configs/puma-rk3399_defconfig b/configs/puma-rk3399_defconfig index 7ce2dc0719..6093943ee8 100644 --- a/configs/puma-rk3399_defconfig +++ b/configs/puma-rk3399_defconfig @@ -49,6 +49,8 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_SYS_MMC_ENV_DEV=1 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y CONFIG_SPL_DM_SEQ_ALIAS=y +CONFIG_GPIO_HOG=y +CONFIG_SPL_GPIO_HOG=y CONFIG_ROCKCHIP_GPIO=y CONFIG_SYS_I2C_ROCKCHIP=y CONFIG_MISC=y @@ -72,10 +74,7 @@ CONFIG_PHY_ROCKCHIP_TYPEC=y CONFIG_DM_PMIC_FAN53555=y CONFIG_PMIC_RK8XX=y CONFIG_SPL_PMIC_RK8XX=y -CONFIG_SPL_DM_REGULATOR=y CONFIG_REGULATOR_PWM=y -CONFIG_SPL_DM_REGULATOR_FIXED=y -CONFIG_DM_REGULATOR_GPIO=y CONFIG_REGULATOR_RK8XX=y CONFIG_PWM_ROCKCHIP=y CONFIG_DM_RESET=y -- 2.37.1