Add a driver for the motorcomm yt8531 gigabit ethernet phy. We have
verified the driver on StarFive VisionFive2 board.
Signed-off-by: Yanhong Wang <yanhong.w...@starfivetech.com>
---
drivers/net/phy/Kconfig | 6 +
drivers/net/phy/Makefile | 1 +
drivers/net/phy/motorcomm.c | 409 ++++++++++++++++++++++++++++++++++++
drivers/net/phy/phy.c | 4 +-
include/phy.h | 1 +
5 files changed, 420 insertions(+), 1 deletion(-)
create mode 100644 drivers/net/phy/motorcomm.c
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 5eaff053a0..aba718566a 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -212,6 +212,12 @@ config PHY_MICREL_KSZ8XXX
endif # PHY_MICREL
+config PHY_MOTORCOMM
+ tristate "Motorcomm PHYs"
+ help
+ Enables support for Motorcomm network PHYs.
+ Currently supports the YT8531 Gigabit Ethernet PHYs.
+
config PHY_MSCC
bool "Microsemi Corp Ethernet PHYs support"
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index d38e99e717..e9523fed2e 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -23,6 +23,7 @@ obj-$(CONFIG_PHY_MARVELL) += marvell.o
obj-$(CONFIG_PHY_MICREL_KSZ8XXX) += micrel_ksz8xxx.o
obj-$(CONFIG_PHY_MICREL_KSZ90X1) += micrel_ksz90x1.o
obj-$(CONFIG_PHY_MESON_GXL) += meson-gxl.o
+obj-$(CONFIG_PHY_MOTORCOMM) += motorcomm.o
obj-$(CONFIG_PHY_NATSEMI) += natsemi.o
obj-$(CONFIG_PHY_NXP_C45_TJA11XX) += nxp-c45-tja11xx.o
obj-$(CONFIG_PHY_NXP_TJA11XX) += nxp-tja11xx.o
diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c
new file mode 100644
index 0000000000..c7e44cfb63
--- /dev/null
+++ b/drivers/net/phy/motorcomm.c
@@ -0,0 +1,409 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Motorcomm 8531 PHY driver.
+ *
+ * Copyright (C) 2023 StarFive Technology Co., Ltd.
+ */
+
+#include <config.h>
+#include <common.h>
+#include <phy.h>
+#include <linux/bitfield.h>
+
+#define PHY_ID_YT8531 0x4f51e91b
+#define PHY_ID_MASK GENMASK(31, 0)
+
+/* Extended Register's Address Offset Register */
+#define YTPHY_PAGE_SELECT 0x1E
+
+/* Extended Register's Data Register */
+#define YTPHY_PAGE_DATA 0x1F
+
+#define YTPHY_SYNCE_CFG_REG 0xA012
+
+#define YTPHY_DTS_OUTPUT_CLK_DIS 0
+#define YTPHY_DTS_OUTPUT_CLK_25M 25000000
+#define YTPHY_DTS_OUTPUT_CLK_125M 125000000
+
+#define YT8531_SCR_SYNCE_ENABLE BIT(6)
+/* 1b0 output 25m clock *default*
+ * 1b1 output 125m clock
+ */
+#define YT8531_SCR_CLK_FRE_SEL_125M BIT(4)
+#define YT8531_SCR_CLK_SRC_MASK GENMASK(3, 1)
+#define YT8531_SCR_CLK_SRC_PLL_125M 0
+#define YT8531_SCR_CLK_SRC_UTP_RX 1
+#define YT8531_SCR_CLK_SRC_SDS_RX 2
+#define YT8531_SCR_CLK_SRC_CLOCK_FROM_DIGITAL 3
+#define YT8531_SCR_CLK_SRC_REF_25M 4
+#define YT8531_SCR_CLK_SRC_SSC_25M 5
+
+/* 1b0 use original tx_clk_rgmii *default*
+ * 1b1 use inverted tx_clk_rgmii.
+ */
+#define YT8531_RC1R_TX_CLK_SEL_INVERTED BIT(14)
+#define YT8531_RC1R_RX_DELAY_MASK GENMASK(13, 10)
+#define YT8531_RC1R_FE_TX_DELAY_MASK GENMASK(7, 4)
+#define YT8531_RC1R_GE_TX_DELAY_MASK GENMASK(3, 0)
+#define YT8531_RC1R_RGMII_0_000_NS 0
+#define YT8531_RC1R_RGMII_0_150_NS 1
+#define YT8531_RC1R_RGMII_0_300_NS 2
+#define YT8531_RC1R_RGMII_0_450_NS 3
+#define YT8531_RC1R_RGMII_0_600_NS 4
+#define YT8531_RC1R_RGMII_0_750_NS 5
+#define YT8531_RC1R_RGMII_0_900_NS 6
+#define YT8531_RC1R_RGMII_1_050_NS 7
+#define YT8531_RC1R_RGMII_1_200_NS 8
+#define YT8531_RC1R_RGMII_1_350_NS 9
+#define YT8531_RC1R_RGMII_1_500_NS 10
+#define YT8531_RC1R_RGMII_1_650_NS 11
+#define YT8531_RC1R_RGMII_1_800_NS 12
+#define YT8531_RC1R_RGMII_1_950_NS 13
+#define YT8531_RC1R_RGMII_2_100_NS 14
+#define YT8531_RC1R_RGMII_2_250_NS 15
+
+/* Phy gmii clock gating Register */
+#define YT8531_CLOCK_GATING_REG 0xC
+#define YT8531_CGR_RX_CLK_EN BIT(12)
+
+/* Specific Status Register */
+#define YTPHY_SPECIFIC_STATUS_REG 0x11
+#define YTPHY_DUPLEX_MASK BIT(13)
+#define YTPHY_DUPLEX_SHIFT 13
+#define YTPHY_SPEED_MODE_MASK GENMASK(15, 14)
+#define YTPHY_SPEED_MODE_SHIFT 14
+
+#define YT8531_EXTREG_SLEEP_CONTROL1_REG 0x27
+#define YT8531_ESC1R_SLEEP_SW BIT(15)
+#define YT8531_ESC1R_PLLON_SLP BIT(14)
+
+#define YT8531_RGMII_CONFIG1_REG 0xA003
+
+#define YT8531_CHIP_CONFIG_REG 0xA001
+#define YT8531_CCR_SW_RST BIT(15)
+/* 1b0 disable 1.9ns rxc clock delay *default*
+ * 1b1 enable 1.9ns rxc clock delay
+ */
+#define YT8531_CCR_RXC_DLY_EN BIT(8)
+#define YT8531_CCR_RXC_DLY_1_900_NS 1900
+
+/**
+ * struct ytphy_cfg_reg_map - map a config value to a register value
+ * @cfg: value in device configuration
+ * @reg: value in the register
+ */
+struct ytphy_cfg_reg_map {
+ u32 cfg;
+ u32 reg;
+};
+
+static const struct ytphy_cfg_reg_map ytphy_rgmii_delays[] = {
+ /* for tx delay / rx delay with YT8531_CCR_RXC_DLY_EN is not set. */
+ { 0, YT8531_RC1R_RGMII_0_000_NS },
+ { 150, YT8531_RC1R_RGMII_0_150_NS },
+ { 300, YT8531_RC1R_RGMII_0_300_NS },
+ { 450, YT8531_RC1R_RGMII_0_450_NS },
+ { 600, YT8531_RC1R_RGMII_0_600_NS },
+ { 750, YT8531_RC1R_RGMII_0_750_NS },
+ { 900, YT8531_RC1R_RGMII_0_900_NS },
+ { 1050, YT8531_RC1R_RGMII_1_050_NS },
+ { 1200, YT8531_RC1R_RGMII_1_200_NS },
+ { 1350, YT8531_RC1R_RGMII_1_350_NS },
+ { 1500, YT8531_RC1R_RGMII_1_500_NS },
+ { 1650, YT8531_RC1R_RGMII_1_650_NS },
+ { 1800, YT8531_RC1R_RGMII_1_800_NS },
+ { 1950, YT8531_RC1R_RGMII_1_950_NS }, /* default tx/rx delay */
+ { 2100, YT8531_RC1R_RGMII_2_100_NS },
+ { 2250, YT8531_RC1R_RGMII_2_250_NS },
+
+ /* only for rx delay with YT8531_CCR_RXC_DLY_EN is set. */
+ { 0 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_0_000_NS },
+ { 150 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_0_150_NS },
+ { 300 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_0_300_NS },
+ { 450 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_0_450_NS },
+ { 600 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_0_600_NS },
+ { 750 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_0_750_NS },
+ { 900 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_0_900_NS },
+ { 1050 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_1_050_NS },
+ { 1200 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_1_200_NS },
+ { 1350 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_1_350_NS },
+ { 1500 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_1_500_NS },
+ { 1650 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_1_650_NS },
+ { 1800 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_1_800_NS },
+ { 1950 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_1_950_NS },
+ { 2100 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_2_100_NS },
+ { 2250 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_2_250_NS }
+};
+
+static u32 ytphy_get_delay_reg_value(struct phy_device *phydev,
+ const char *prop_name,
+ const struct ytphy_cfg_reg_map *tbl,
+ int tb_size,
+ u16 *rxc_dly_en,
+ u32 dflt)
+{
+ int tb_size_half = tb_size / 2;
+ u32 val;
+ int i;
+
+ if (ofnode_read_u32(phydev->node, prop_name, &val))
+ goto err_dts_val;
+
+ /* when rxc_dly_en is NULL, it is get the delay for tx, only half of
+ * tb_size is valid.
+ */
+ if (!rxc_dly_en)
+ tb_size = tb_size_half;
+
+ for (i = 0; i < tb_size; i++) {
+ if (tbl[i].cfg == val) {
+ if (rxc_dly_en && i < tb_size_half)
+ *rxc_dly_en = 0;
+ return tbl[i].reg;
+ }
+ }
+
+ pr_warn("Unsupported value %d for %s using default (%u)\n",
+ val, prop_name, dflt);
+
+err_dts_val:
+ /* when rxc_dly_en is not NULL, it is get the delay for rx.
+ * The rx default in dts and ytphy_rgmii_clk_delay_config is 1950 ps,
+ * so YT8531_CCR_RXC_DLY_EN should not be set.
+ */
+ if (rxc_dly_en)
+ *rxc_dly_en = 0;
+
+ return dflt;
+}
+
+static int ytphy_modify_ext(struct phy_device *phydev, u16 regnum, u16 mask,
+ u16 set)
+{
+ int ret;
+
+ ret = phy_write(phydev, MDIO_DEVAD_NONE, YTPHY_PAGE_SELECT, regnum);
+ if (ret < 0)
+ return ret;
+
+ return phy_modify(phydev, MDIO_DEVAD_NONE, YTPHY_PAGE_DATA, mask, set);
+}
+
+static int ytphy_rgmii_clk_delay_config(struct phy_device *phydev)
+{
+ int tb_size = ARRAY_SIZE(ytphy_rgmii_delays);
+ u16 rxc_dly_en = YT8531_CCR_RXC_DLY_EN;
+ u32 rx_reg, tx_reg;
+ u16 mask, val = 0;
+ int ret;
+
+ rx_reg = ytphy_get_delay_reg_value(phydev, "rx-internal-delay-ps",
+ ytphy_rgmii_delays, tb_size,
+ &rxc_dly_en,
+ YT8531_RC1R_RGMII_1_950_NS);
+ tx_reg = ytphy_get_delay_reg_value(phydev, "tx-internal-delay-ps",
+ ytphy_rgmii_delays, tb_size, NULL,
+ YT8531_RC1R_RGMII_1_950_NS);
+
+ switch (phydev->interface) {
+ case PHY_INTERFACE_MODE_RGMII:
+ rxc_dly_en = 0;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ val |= FIELD_PREP(YT8531_RC1R_RX_DELAY_MASK, rx_reg);
+ break;
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ rxc_dly_en = 0;
+ val |= FIELD_PREP(YT8531_RC1R_GE_TX_DELAY_MASK, tx_reg);
+ break;
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ val |= FIELD_PREP(YT8531_RC1R_RX_DELAY_MASK, rx_reg) |
+ FIELD_PREP(YT8531_RC1R_GE_TX_DELAY_MASK, tx_reg);
+ break;
+ default: /* do not support other modes */
+ return -EOPNOTSUPP;
+ }
+
+ ret = ytphy_modify_ext(phydev, YT8531_CHIP_CONFIG_REG,
+ YT8531_CCR_RXC_DLY_EN, rxc_dly_en);
+ if (ret < 0)
+ return ret;
+
+ /* Generally, it is not necessary to adjust YT8531_RC1R_FE_TX_DELAY */
+ mask = YT8531_RC1R_RX_DELAY_MASK | YT8531_RC1R_GE_TX_DELAY_MASK;
+ return ytphy_modify_ext(phydev, YT8531_RGMII_CONFIG1_REG, mask, val);
+}
+
+static int yt8531_parse_status(struct phy_device *phydev)
+{
+ int val;
+ int speed, speed_mode;
+
+ val = phy_read(phydev, MDIO_DEVAD_NONE, YTPHY_SPECIFIC_STATUS_REG);
+ if (val < 0)
+ return val;
+
+ speed_mode = (val & YTPHY_SPEED_MODE_MASK) >> YTPHY_SPEED_MODE_SHIFT;
+ switch (speed_mode) {
+ case 2:
+ speed = SPEED_1000;
+ break;
+ case 1:
+ speed = SPEED_100;
+ break;
+ default:
+ speed = SPEED_10;
+ break;
+ }
+
+ phydev->speed = speed;
+ phydev->duplex = (val & YTPHY_DUPLEX_MASK) >> YTPHY_DUPLEX_SHIFT;
+
+ return 0;
+}
+
+static int yt8531_startup(struct phy_device *phydev)
+{
+ bool tx_clk_adj_enabled = false;
+ bool tx_clk_1000_inverted = false;
+ bool tx_clk_100_inverted = false;
+ bool tx_clk_10_inverted = false;
+ u16 val = 0;
+ int ret;
+
+ ret = genphy_update_link(phydev);
+ if (ret)
+ return ret;
+
+ ret = yt8531_parse_status(phydev);
+ if (ret)
+ return ret;
+
+ if (ofnode_read_bool(phydev->node, "motorcomm,tx-clk-adj-enabled"))
+ tx_clk_adj_enabled = true;
+
+ if (!tx_clk_adj_enabled)
+ return 0;
+
+ if (ofnode_read_bool(phydev->node, "motorcomm,tx-clk-10-inverted"))
+ tx_clk_10_inverted = true;
+ if (ofnode_read_bool(phydev->node, "motorcomm,tx-clk-100-inverted"))
+ tx_clk_100_inverted = true;
+ if (ofnode_read_bool(phydev->node, "motorcomm,tx-clk-1000-inverted"))
+ tx_clk_1000_inverted = true;
+
+ if (phydev->speed < 0)
+ return -EINVAL;
+
+ switch (phydev->speed) {
+ case SPEED_1000:
+ if (tx_clk_1000_inverted)
+ val = YT8531_RC1R_TX_CLK_SEL_INVERTED;
+ break;
+ case SPEED_100:
+ if (tx_clk_100_inverted)
+ val = YT8531_RC1R_TX_CLK_SEL_INVERTED;
+ break;
+ case SPEED_10:
+ if (tx_clk_10_inverted)
+ val = YT8531_RC1R_TX_CLK_SEL_INVERTED;
+ break;
+ default:
+ printf("UNKNOWN SPEED\n");
+ return -EINVAL;
+ }
+
+ ret = ytphy_modify_ext(phydev, YT8531_RGMII_CONFIG1_REG,
+ YT8531_RC1R_TX_CLK_SEL_INVERTED, val);
+ if (ret < 0)
+ pr_warn("Modify TX_CLK_SEL err:%d\n", ret);
+
+ return 0;
+}
+
+static int yt8531_config(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = genphy_config_aneg(phydev);
+ if (ret < 0)
+ return ret;
+
+ ret = ytphy_rgmii_clk_delay_config(phydev);
+ if (ret < 0)
+ return ret;
+
+ if (ofnode_read_bool(phydev->node, "motorcomm,auto-sleep-disabled")) {
+ /* disable auto sleep */
+ ret = ytphy_modify_ext(phydev,
+ YT8531_EXTREG_SLEEP_CONTROL1_REG,
+ YT8531_ESC1R_SLEEP_SW, 0);
+ if (ret < 0)
+ return ret;
+ }
+
+ if (ofnode_read_bool(phydev->node, "motorcomm,keep-pll-enabled")) {
+ /* enable RXC clock when no wire plug */
+ ret = ytphy_modify_ext(phydev,
+ YT8531_CLOCK_GATING_REG,
+ YT8531_CGR_RX_CLK_EN, 0);
+ if (ret < 0)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int yt8531_probe(struct phy_device *phydev)
+{
+ u16 mask, val;
+ u32 freq;
+
+ if (ofnode_read_u32(phydev->node, "motorcomm,clk-out-frequency-hz",
&freq))
+ freq = YTPHY_DTS_OUTPUT_CLK_DIS;
+
+ switch (freq) {
+ case YTPHY_DTS_OUTPUT_CLK_DIS:
+ mask = YT8531_SCR_SYNCE_ENABLE;
+ val = 0;
+ break;
+ case YTPHY_DTS_OUTPUT_CLK_25M:
+ mask = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_SRC_MASK |
+ YT8531_SCR_CLK_FRE_SEL_125M;
+ val = YT8531_SCR_SYNCE_ENABLE |
+ FIELD_PREP(YT8531_SCR_CLK_SRC_MASK,
+ YT8531_SCR_CLK_SRC_REF_25M);
+ break;
+ case YTPHY_DTS_OUTPUT_CLK_125M:
+ mask = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_SRC_MASK |
+ YT8531_SCR_CLK_FRE_SEL_125M;
+ val = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_FRE_SEL_125M |
+ FIELD_PREP(YT8531_SCR_CLK_SRC_MASK,
+ YT8531_SCR_CLK_SRC_PLL_125M);
+ break;
+ default:
+ pr_warn("Freq err:%u\n", freq);
+ return -EINVAL;
+ }
+
+ return ytphy_modify_ext(phydev, YTPHY_SYNCE_CFG_REG, mask,
+ val);
+}
+
+static struct phy_driver motorcomm8531_driver = {
+ .name = "YT8531 Gigabit Ethernet",
+ .uid = PHY_ID_YT8531,
+ .mask = PHY_ID_MASK,
+ .features = PHY_GBIT_FEATURES,
+ .probe = &yt8531_probe,
+ .config = &yt8531_config,
+ .startup = &yt8531_startup,
+ .shutdown = &genphy_shutdown,
+};
+
+int phy_motorcomm_init(void)
+{
+ phy_register(&motorcomm8531_driver);
+
+ return 0;
+}
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index 80230b907c..78bde61798 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -570,6 +570,9 @@ int phy_init(void)
#endif
#ifdef CONFIG_PHY_XILINX_GMII2RGMII
phy_xilinx_gmii2rgmii_init();
+#endif
+#ifdef CONFIG_PHY_MOTORCOMM
+ phy_motorcomm_init();
#endif
genphy_init();
@@ -755,7 +758,6 @@ static struct phy_device *create_phy_by_mask(struct mii_dev
*bus,
while (phy_mask) {
int addr = ffs(phy_mask) - 1;
int r = get_phy_id(bus, addr, devad, &phy_id);
-
/*
* If the PHY ID is flat 0 we ignore it. There are C45 PHYs
* that return all 0s for C22 reads (like Aquantia AQR112) and
diff --git a/include/phy.h b/include/phy.h
index 87aa86c2e7..f7bb2fe0af 100644
--- a/include/phy.h
+++ b/include/phy.h
@@ -344,6 +344,7 @@ int phy_mscc_init(void);
int phy_fixed_init(void);
int phy_ncsi_init(void);
int phy_xilinx_gmii2rgmii_init(void);
+int phy_motorcomm_init(void);
int board_phy_config(struct phy_device *phydev);
int get_phy_id(struct mii_dev *bus, int addr, int devad, u32 *phy_id);
--
2.17.1
