Hi Milan, Le jeu. 7 déc. 2023 à 11:09, Milan Zamazal <mzama...@redhat.com> a écrit :
> Peng Fan <peng....@oss.nxp.com> writes: > > > On 5/24/2023 3:21 AM, Gilles Talis wrote: > >> Add support for the Polyhex Debix Model A SBC board. > >> It is an industrial grade single board computer based on > >> NXP's i.MX 8M Plus. > >> Currently supported interfaces are: > >> - Serial console > >> - Micro SD > >> - eQOS and FEC Ethernet > >> imx8mp-debix-model-a.dts is taken from Linux 6.3. > >> Signed-off-by: Gilles Talis<gilles.ta...@gmail.com> > > > > Reviewed-by: Peng Fan <peng....@nxp.com> > > Do you know why the patch has been left (as far as I can see) without > further action? > I don't know. I assume the maintainer is very busy or has missed it. I was planning to do a resend in the next few weeks. > > BTW, I applied it to current master, compiled approximately following > https://docs.u-boot.org/en/latest/board/nxp/imx8mp_evk.html and tried to > use it on Debix Model A. U-Boot starts but cannot find the partition > table on the SD card: > > U-Boot SPL 2024.01-rc3-07226-g43f2873fa9-dirty (Jan 01 1980 - 00:00:00 > +0000) > Normal Boot > WDT: Started watchdog@30280000 with servicing every 1000ms (60s > timeout) > Trying to boot from BOOTROM > Boot Stage: Primary boot > image offset 0x8000, pagesize 0x200, ivt offset 0x0 > NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.6-0-g15e8ff164-dirty > NOTICE: BL31: Built : 00:00:00, Jan 1 1980 > > > U-Boot 2024.01-rc3-07226-g43f2873fa9-dirty (Jan 01 1980 - 00:00:00 +0000) > > CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz > Reset cause: POR > Model: Polyhex Debix Model A i.MX8MPlus board > DRAM: 2 GiB > Core: 83 devices, 22 uclasses, devicetree: separate > WDT: Started watchdog@30280000 with servicing every 1000ms (60s > timeout) > MMC: FSL_SDHC: 1, FSL_SDHC: 2 > Loading Environment from MMC... *** Warning - bad CRC, using default > environment > > In: serial@30890000 > Out: serial@30890000 > Err: serial@30890000 > Net: eth1: ethernet@30bf0000 [PRIME] > Hit any key to stop autoboot: 2 <0x08><0x08><0x08> 1 <0x08><0x08><0x08> > 0 > switch to partitions #0, OK > mmc1 is current device > Scanning mmc 1:1... > ,** No partition table - mmc 1 ** > Couldn't find partition mmc 1:1 > ,** No partition table - mmc 1 ** > Couldn't find partition mmc 1:1 > ,** No partition table - mmc 1 ** > Couldn't find partition mmc 1:1 > ,** No partition table - mmc 1 ** > Couldn't find partition mmc 1:1 > ,** No partition table - mmc 1 ** > Couldn't find partition mmc 1:1 > ,** No partition table - mmc 1 ** > Couldn't find partition mmc 1:1 > ,** No partition table - mmc 1 ** > Couldn't find partition mmc 1:1 > <0x1b>7<0x1b>[r<0x1b>[999;999H<0x1b>[6n<0x1b>8Card did not respond to > voltage select! : -110 > No EFI system partition > No EFI system partition > Failed to persist EFI variables > Remove /soc@0/bus@30800000/ethernet@30be0000:phy-reset-gpios > BootOrder not defined > EFI boot manager: Cannot load any image > ,** No partition table - mmc 1 ** > Couldn't find partition mmc 1:1 > Card did not respond to voltage select! : -110 > u-boot=> > > When I use an old U-Boot blob provided by Debix, it boots fine from the > same SD card. The SD card contains a Fedora aarch64 image with a msdos > partition table. > > Do you know what could be wrong? > Interesting. I don't have a clue yet,. but let me give it a try and come back to you. Where can I download the Fedora aarch64 image you mentioned above? > > Regards, > Milan > > Thanks! Gilles.