Gilles Talis <gilles.ta...@gmail.com> writes: > Hi Milan, > > Le jeu. 7 déc. 2023 à 11:09, Milan Zamazal <mzama...@redhat.com> a écrit : > >> Peng Fan <peng....@oss.nxp.com> writes: >> >> > On 5/24/2023 3:21 AM, Gilles Talis wrote: >> >> Add support for the Polyhex Debix Model A SBC board. >> >> It is an industrial grade single board computer based on >> >> NXP's i.MX 8M Plus. >> >> Currently supported interfaces are: >> >> - Serial console >> >> - Micro SD >> >> - eQOS and FEC Ethernet >> >> imx8mp-debix-model-a.dts is taken from Linux 6.3. >> >> Signed-off-by: Gilles Talis<gilles.ta...@gmail.com> >> > >> > Reviewed-by: Peng Fan <peng....@nxp.com> >> >> Do you know why the patch has been left (as far as I can see) without >> further action? >> > I don't know. I assume the maintainer is very busy or has missed it. I was > planning to do a resend in the next few weeks. > > >> >> BTW, I applied it to current master, compiled approximately following >> https://docs.u-boot.org/en/latest/board/nxp/imx8mp_evk.html and tried to >> use it on Debix Model A. U-Boot starts but cannot find the partition >> table on the SD card: >> >> U-Boot SPL 2024.01-rc3-07226-g43f2873fa9-dirty (Jan 01 1980 - 00:00:00 >> +0000) >> Normal Boot >> WDT: Started watchdog@30280000 with servicing every 1000ms (60s >> timeout) >> Trying to boot from BOOTROM >> Boot Stage: Primary boot >> image offset 0x8000, pagesize 0x200, ivt offset 0x0 >> NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.6-0-g15e8ff164-dirty >> NOTICE: BL31: Built : 00:00:00, Jan 1 1980 >> >> >> U-Boot 2024.01-rc3-07226-g43f2873fa9-dirty (Jan 01 1980 - 00:00:00 +0000) >> >> CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz >> Reset cause: POR >> Model: Polyhex Debix Model A i.MX8MPlus board >> DRAM: 2 GiB >> Core: 83 devices, 22 uclasses, devicetree: separate >> WDT: Started watchdog@30280000 with servicing every 1000ms (60s >> timeout) >> MMC: FSL_SDHC: 1, FSL_SDHC: 2 >> Loading Environment from MMC... *** Warning - bad CRC, using default >> environment >> >> In: serial@30890000 >> Out: serial@30890000 >> Err: serial@30890000 >> Net: eth1: ethernet@30bf0000 [PRIME] >> Hit any key to stop autoboot: 2 <0x08><0x08><0x08> 1 <0x08><0x08><0x08> >> 0 >> switch to partitions #0, OK >> mmc1 is current device >> Scanning mmc 1:1... >> ,** No partition table - mmc 1 ** >> Couldn't find partition mmc 1:1 >> ,** No partition table - mmc 1 ** >> Couldn't find partition mmc 1:1 >> ,** No partition table - mmc 1 ** >> Couldn't find partition mmc 1:1 >> ,** No partition table - mmc 1 ** >> Couldn't find partition mmc 1:1 >> ,** No partition table - mmc 1 ** >> Couldn't find partition mmc 1:1 >> ,** No partition table - mmc 1 ** >> Couldn't find partition mmc 1:1 >> ,** No partition table - mmc 1 ** >> Couldn't find partition mmc 1:1 >> <0x1b>7<0x1b>[r<0x1b>[999;999H<0x1b>[6n<0x1b>8Card did not respond to >> voltage select! : -110 >> No EFI system partition >> No EFI system partition >> Failed to persist EFI variables >> Remove /soc@0/bus@30800000/ethernet@30be0000:phy-reset-gpios >> BootOrder not defined >> EFI boot manager: Cannot load any image >> ,** No partition table - mmc 1 ** >> Couldn't find partition mmc 1:1 >> Card did not respond to voltage select! : -110 >> u-boot=> >> >> When I use an old U-Boot blob provided by Debix, it boots fine from the >> same SD card. The SD card contains a Fedora aarch64 image with a msdos >> partition table. >> >> Do you know what could be wrong? >> > Interesting. I don't have a clue yet,. but let me give it a try and come > back to you. Where can I download the Fedora aarch64 image you mentioned > above?
I flashed the image freshly, to another SD card, and it boots happily. So I can confirm your patch works. :-) I don't know what's wrong with the partition table on the original SD card. I manipulated with the partitions and their properties a bit before but parted or the other versions of U-Boot I tried don't report any problem. Maybe the U-Boot version from master that I happened to compile does something differently. Anyway, it's unlikely to be related to this patch as it boots fine on a freshly flashed SD card. Thank you for the patch, hopefully it'll get merged. Regards, Milan