This series adds support for Xilinx qspi parallel and stacked memeories.
In parallel mode, the current implementation assumes that a maximum of two
flashes are connected. The QSPI controller splits the data evenly between both
the flashes so, both the flashes that are connected in parallel mode should be
identical.
During each operation SPI-NOR sets 0th bit for CS0 & 1st bit for CS1 in
nor->flags.
In stacked mode the current implementation assumes that a maximum of two
flashes are connected and both the flashes are of same make but can differ in
sizes. So, except the sizes all other flash parameters of both the flashes are
identical.
Spi-nor will pass on the appropriate flash select flag to low level driver, and
it will select pass all the data to that particular flash.
Write operation in parallel mode are performed in page size * 2 chunks as each
write operation results in writing both the flashes. For doubling the address
space each operation is performed at addr/2 flash offset, where addr is the
address specified by the user.
Similarly for read and erase operations it will read from both flashes, so size
and offset are divided by 2 and send to flash.
Changes in v2:
- Fixed the compilation issues.
Changes in v3:
- Fixed the CI issues.
Changes in v4:
- Removed the dio,dummy_bytes variables from zynq_qspi driver.
- Fix the compilation issue by including the DM_SPI config.
Changes in v5:
- Fixed the issue reported by buildman.
Changes in v6:
- Fixed the issues reported while running the sandbox test cases.
Changes in v7:
- Fixed the issues reported while running these da850evm_defconfig,
imx28_xea_defconfig configs.
- Fixed the issue when DM_SPI config is disabled.
- Fixed the issue while running the sandbox_noinst_defconfig with spl
./spl/u-boot-spl -d arch/sandbox/dts/test.dtb
jedec_spi_nor spi.bin@0: has no valid 'reg' property (-12)
jedec_spi_nor spi.bin@1: has no valid 'reg' property (-12)
### ERROR ### Please RESET the board ###
Ashok Reddy Soma (4):
mtd: spi-nor: Add parallel and stacked memories support
mtd: spi-nor: Add parallel memories support for read_sr and read_fsr
mtd: spi-nor: Add parallel and stacked memories support in read_bar
and write_bar
spi: spi-uclass: Read chipselect and restrict capabilities
Venkatesh Yadav Abbarapu (2):
spi: zynqmp_gqspi: Add parallel memories support in GQSPI driver
spi: zynq_qspi: Add parallel memories support in QSPI driver
drivers/mtd/spi/sandbox.c | 2 +-
drivers/mtd/spi/spi-nor-core.c | 398 ++++++++++++++++++++++++++++-----
drivers/spi/altera_spi.c | 4 +-
drivers/spi/atcspi200_spi.c | 2 +-
drivers/spi/ath79_spi.c | 2 +-
drivers/spi/atmel_spi.c | 6 +-
drivers/spi/bcm63xx_hsspi.c | 42 ++--
drivers/spi/bcm63xx_spi.c | 6 +-
drivers/spi/bcmbca_hsspi.c | 34 +--
drivers/spi/cf_spi.c | 6 +-
drivers/spi/davinci_spi.c | 8 +-
drivers/spi/fsl_dspi.c | 18 +-
drivers/spi/fsl_espi.c | 4 +-
drivers/spi/fsl_qspi.c | 4 +-
drivers/spi/gxp_spi.c | 2 +-
drivers/spi/mpc8xx_spi.c | 4 +-
drivers/spi/mpc8xxx_spi.c | 10 +-
drivers/spi/mscc_bb_spi.c | 4 +-
drivers/spi/mxc_spi.c | 6 +-
drivers/spi/npcm_fiu_spi.c | 14 +-
drivers/spi/nxp_fspi.c | 2 +-
drivers/spi/octeon_spi.c | 2 +-
drivers/spi/omap3_spi.c | 4 +-
drivers/spi/pic32_spi.c | 2 +-
drivers/spi/rk_spi.c | 4 +-
drivers/spi/rockchip_sfc.c | 2 +-
drivers/spi/spi-aspeed-smc.c | 28 +--
drivers/spi/spi-mxic.c | 6 +-
drivers/spi/spi-qup.c | 4 +-
drivers/spi/spi-sifive.c | 6 +-
drivers/spi/spi-sn-f-ospi.c | 2 +-
drivers/spi/spi-sunxi.c | 6 +-
drivers/spi/spi-synquacer.c | 4 +-
drivers/spi/spi-uclass.c | 33 ++-
drivers/spi/stm32_qspi.c | 2 +-
drivers/spi/stm32_spi.c | 4 +-
drivers/spi/ti_qspi.c | 14 +-
drivers/spi/xilinx_spi.c | 4 +-
drivers/spi/zynq_qspi.c | 119 ++++++++--
drivers/spi/zynq_spi.c | 6 +-
drivers/spi/zynqmp_gqspi.c | 141 ++++++++++--
include/linux/mtd/spi-nor.h | 12 +
include/spi.h | 23 +-
lib/acpi/acpi_device.c | 2 +-
44 files changed, 781 insertions(+), 227 deletions(-)
--
2.25.1
