TBIPA has been set in dtsec_init_phy () funciton in drivers/net/fm/eth.c
So remove the duplicate code on platform Ethernet code.
Signed-off-by: Roy Zang <tie-fei.z...@freescale.com>
Cc: Andy Fleming <aflem...@freescale.com>
Cc: Kumar Gala <ga...@kernel.crashing.org>
---
Tested on P5020DS
board/freescale/corenet_ds/eth_hydra.c | 8 --------
board/freescale/corenet_ds/eth_p4080.c | 8 --------
board/freescale/p2041rdb/eth.c | 8 --------
3 files changed, 0 insertions(+), 24 deletions(-)
diff --git a/board/freescale/corenet_ds/eth_hydra.c
b/board/freescale/corenet_ds/eth_hydra.c
index 91b3408..639358d 100644
--- a/board/freescale/corenet_ds/eth_hydra.c
+++ b/board/freescale/corenet_ds/eth_hydra.c
@@ -395,7 +395,6 @@ void fdt_fixup_board_enet(void *fdt)
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_FMAN_ENET
- struct dtsec *tsec = (void *)CONFIG_SYS_FSL_FM1_DTSEC1_ADDR;
struct fsl_pq_mdio_info dtsec_mdio_info;
struct tgec_mdio_info tgec_mdio_info;
unsigned int i, slot;
@@ -405,13 +404,6 @@ int board_eth_init(bd_t *bis)
initialize_lane_to_slot();
- /*
- * Set TBIPA on FM1@DTSEC1. This is needed for configurations
- * where FM1@DTSEC1 isn't used directly, since it provides
- * MDIO for other ports.
- */
- out_be32(&tsec->tbipa, CONFIG_SYS_TBIPA_VALUE);
-
/* We want to use the PIXIS to configure MUX routing, not GPIOs. */
setbits_8(&pixis->brdcfg2, BRDCFG2_REG_GPIO_SEL);
diff --git a/board/freescale/corenet_ds/eth_p4080.c
b/board/freescale/corenet_ds/eth_p4080.c
index d4657f7..208b97a 100644
--- a/board/freescale/corenet_ds/eth_p4080.c
+++ b/board/freescale/corenet_ds/eth_p4080.c
@@ -295,7 +295,6 @@ int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_FMAN_ENET
ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
- struct dtsec *tsec = (void *)CONFIG_SYS_FSL_FM1_DTSEC1_ADDR;
int i;
struct fsl_pq_mdio_info dtsec_mdio_info;
struct tgec_mdio_info tgec_mdio_info;
@@ -321,13 +320,6 @@ int board_eth_init(bd_t *bis)
SLOT5, /* 17 - Bank 3:D */
};
- /*
- * Set TBIPA on FM1@DTSEC1. This is needed for configurations
- * where FM1@DTSEC1 isn't used directly, since it provides
- * MDIO for other ports.
- */
- out_be32(&tsec->tbipa, CONFIG_SYS_TBIPA_VALUE);
-
/* Initialize the mdio_mux array so we can recognize empty elements */
for (i = 0; i < NUM_FM_PORTS; i++)
mdio_mux[i] = EMI_NONE;
diff --git a/board/freescale/p2041rdb/eth.c b/board/freescale/p2041rdb/eth.c
index 0a1dfa7..4b0d577 100644
--- a/board/freescale/p2041rdb/eth.c
+++ b/board/freescale/p2041rdb/eth.c
@@ -139,7 +139,6 @@ void board_ft_fman_fixup_port(void *fdt, char *compat,
phys_addr_t addr,
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_FMAN_ENET
- struct dtsec *tsec = (void *)CONFIG_SYS_FSL_FM1_DTSEC1_ADDR;
struct fsl_pq_mdio_info dtsec_mdio_info;
struct tgec_mdio_info tgec_mdio_info;
unsigned int i, slot;
@@ -149,13 +148,6 @@ int board_eth_init(bd_t *bis)
initialize_lane_to_slot();
- /*
- * Set TBIPA on FM1@DTSEC1. This is needed for configurations
- * where FM1@DTSEC1 isn't used directly, since it provides
- * MDIO for other ports.
- */
- out_be32(&tsec->tbipa, CONFIG_SYS_TBIPA_VALUE);
-
dtsec_mdio_info.regs =
(struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
--
1.6.0.6
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
