Add the production boot environment in CFG_EXTRA_ENV_SETTINGS. The kernel FIT at NOR offset 0x1000000 carries the kernel, DTB, optional ramdisk and the LX2160A management complex artefacts (mc, dpc-<carrier>, dpl-<carrier>) as sub-images.
The usage of those variables is described in doc/board/nxp/nbxv3.rst. Signed-off-by: Vincent Jardin <[email protected]> --- configs/nbxv3_tfa_defconfig | 8 ++++++++ include/configs/nbxv3.h | 40 ++++++++++++++++++++++++++++++++++++- 2 files changed, 47 insertions(+), 1 deletion(-) diff --git a/configs/nbxv3_tfa_defconfig b/configs/nbxv3_tfa_defconfig index a4c8419f0c3..bc90bb0594c 100644 --- a/configs/nbxv3_tfa_defconfig +++ b/configs/nbxv3_tfa_defconfig @@ -25,8 +25,12 @@ CONFIG_MP=y CONFIG_DYNAMIC_SYS_CLK_FREQ=y # CONFIG_EFI_LOADER is not set CONFIG_FIT_VERBOSE=y +CONFIG_BOOTDELAY=3 CONFIG_OF_BOARD_SETUP=y CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyAMA0,115200 earlycon=pl011,mmio32,0x21c0000 nokaslr" +CONFIG_USE_PREBOOT=y CONFIG_SYS_PBSIZE=532 CONFIG_LAST_STAGE_INIT=y # CONFIG_ID_EEPROM is not set @@ -52,8 +56,12 @@ CONFIG_CMD_CACHE=y CONFIG_CMD_RNG=y CONFIG_CMD_LOG=y CONFIG_OF_CONTROL=y +CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_ENV_SPI_BUS=3 +CONFIG_USE_ETHPRIME=y +CONFIG_ETHPRIME="lanconsole0" +CONFIG_NET_RANDOM_ETHADDR=y CONFIG_FSL_CAAM=y CONFIG_DYNAMIC_DDR_CLK_FREQ=y CONFIG_DDR_ECC=y diff --git a/include/configs/nbxv3.h b/include/configs/nbxv3.h index 287f4110a7c..c266e0f9fe2 100644 --- a/include/configs/nbxv3.h +++ b/include/configs/nbxv3.h @@ -14,6 +14,44 @@ "pci_iommu_extra=pci@0x3600000,1.0.0,hp," \ "pci@0x3700000,1.0.0,hp," \ "pci@0x3800000,1.0.0,hp," \ - "pci@0x3900000,1.0.0,hp\0" + "pci@0x3900000,1.0.0,hp\0" \ + "kernel_addr_r=0xc0000000\0" \ + "fit_nor_offset=0x1000000\0" \ + "fit_nor_size=0x1000000\0" \ + "mcmemsize=0x70000000\0" \ + "mcinitcmd=" \ + "sf probe 3:0 && " \ + "sf read ${kernel_addr_r} ${fit_nor_offset} ${fit_nor_size} && "\ + "imxtract ${kernel_addr_r} mc 0xa8000000 && " \ + "imxtract ${kernel_addr_r} dpc-${carrier} 0xa9000000 && "\ + "imxtract ${kernel_addr_r} dpl-${carrier} 0xaa000000 && "\ + "fsl_mc start mc 0xa8000000 0xa9000000 && " \ + "fsl_mc lazyapply dpl 0xaa000000\0" \ + "mc_init=bootm ${kernel_addr_r}#conf-${carrier}\0" \ + "linux_boot_fit=" \ + "sf probe 3:0 && " \ + "sf read ${kernel_addr_r} ${fit_nor_offset} ${fit_nor_size} && "\ + "bootm ${kernel_addr_r}#conf-${carrier}\0" \ + "host_boot=" \ + "load semihosting - ${kernel_addr_r} fit.itb && " \ + "bootm ${kernel_addr_r}#conf-${carrier}\0" \ + "provision_openocd_fit=" \ + "load semihosting - ${kernel_addr_r} fit.itb && " \ + "sf probe 3:0 && " \ + "sf erase ${fit_nor_offset} ${fit_nor_size} && " \ + "sf write ${kernel_addr_r} ${fit_nor_offset} ${filesize} && "\ + "reset\0" \ + "xspi_bootcmd=" \ + "cp.b 0x21000000 ${kernel_addr_r} ${fit_nor_size} && " \ + "bootm ${kernel_addr_r}#conf-${carrier}\0" \ + "fsl_bootcmd_mcinitcmd_set=y\0" \ + "bootcmd=run mc_init || run provision_openocd_fit\0" \ + "mdio_list=" \ + "echo === Nbxv3 probed PHYs === && " \ + "mdio list\0" \ + "PS1=nbxv3> \0" \ + "ps_refresh=" \ + "setenv PS1 \"nbxv3 ${ethact} ${ipaddr}> \"\0" \ + "preboot=run mdio_list ; run ps_refresh\0" #endif /* __NBXV3_H */ -- 2.43.0
