On Wed, Aug 19, 2026 at 8:59 PM Iker Pedrosa <[email protected]> wrote: > > El mié, 19 ago 2026 a las 5:55, Eric Chung (<[email protected]>) > escribió: > > > > This series adds MMC support for the SpacemiT K1: an SDHCI platform > > driver, the SD card device-tree overlay, defconfig options, and SPL > > boot-device selection from the SoC strap/config registers. The SDHCI > > driver is usable in both SPL and U-Boot proper. > > > > A flashing guide (doc/board/spacemit/k1-flash.rst) describes how to > > write images to eMMC. > > > > --- > > Changes in v9: > > - spl: Enhance detection on booting from SD. > > - dts: Synched upstream DTS files for K1. > > - doc: Create SD card image from scratch. > > - mmc: Avoid to use CMD18 on SD card in SPL. > > - pinctrl: Drop "fix drive strength configuration". > > - Link to v8: > > https://patch.msgid.link/[email protected] > > > > Changes in v8: > > - doc: Remove SD card. > > - Link to v7: > > https://patch.msgid.link/[email protected] > > > > Changes in v7: > > - env: Drop env support on the mmc series. > > - dts: Sync upstream DTS files for spacemit. > > - pinctrl: Simply clrsetbits_le32() on pull-up/pull-down configuration. > > - spl: Fix DTB matching. > > - Link to v6: > > https://patch.msgid.link/[email protected] > > > > Changes in v6: > > - pinctrl: Fix drive strength configuration. > > - pinctrl: Fix pull-up/pull-down configuration. > > - pinctrl: Use dev_read_phandle_with_args() to fetch "spacemit,syscon" > > instead. > > - spacemit: rebase on latest upstream branch. > > - Link to v5: > > https://patch.msgid.link/[email protected] > > > > Changes in v5: > > - mmc: Split CMD23 support out. > > - mmc: Use read_poll_timeout(). > > - mmc: Set pinctrl state based on selected timing mode. > > - mmc: Remove the condition based on quirks. > > - pinctrl: Fix power source argument. > > - dts: Add missing power source on mmc pins. > > - Link to v4: > > https://patch.msgid.link/[email protected] > > > > Changes in v4: > > - mmc: Add CMD23 for write. > > - mmc: Fix CMD23 only for CMD18. > > - mmc: Update bulk release operations on reset and clocks for spacemit > > platform driver. > > - MAINTAINER: update the maintainer of Spacemit K1. > > - Link to v3: > > https://patch.msgid.link/[email protected] > > > > Changes in v3: > > - pinctrl: Fix "fast" by "uhs". > > - pinctrl: Add syscon dependency. > > - mmc: Fix quick by capability. > > - doc: Add SD boot support. > > - Link to v2: > > https://lore.kernel.org/u-boot/[email protected]/T/#m2aba875a2696a7bb9b704618d22ae2fd7f7f5acc > > > > Changes in v2: > > - cmd: drop patches on eminfo & tlv_eeprom. > > - configs: Enable ADMA and SYSCON support. > > - dts: Use vmmc-supply as vqmmc-supply on the SD card node. > > - mmc: k1: Enable ADMA mode support, use CMD23 for multi-block > > read/write, correct pinctrl state from "fast" to "uhs". > > - mmc: sdhci: Add new quirk patch to enable CMD23 for multi-block > > transfers. > > - pinctrl: k1: Add new IO power domain configuration support for > > dual-voltage GPIO banks. > > - spacemit: k1: Use FIELD_GET() to parse boot strap mode. > > - Link to v1: > > https://lore.kernel.org/u-boot/[email protected]/ > > > > To: [email protected] > > To: [email protected] > > To: [email protected] > > Cc: Huan Zhou <[email protected]> > > Cc: Tom Rini <[email protected]> > > Cc: Tim Ouyang <[email protected]> > > Cc: Leo Liang <[email protected]> > > Cc: Raymond Mao <[email protected]> > > Cc: Peng Fan <[email protected]> > > Cc: Jaehoon Chung <[email protected]> > > Cc: Bhimeswararao Matsa <[email protected]> > > Cc: Tanmay Kathpalia <[email protected]> > > Cc: Kaustabh Chakraborty <[email protected]> > > Cc: Han Xu <[email protected]> > > Cc: Yanir Levin <[email protected]> > > Cc: Christoph Stoidner <[email protected]> > > Cc: Balsundar Ponnusamy <[email protected]> > > Cc: Daniel Palmer <[email protected]> > > Cc: Anshul Dalal <[email protected]> > > Cc: Bastien Curutchet <[email protected]> > > Cc: Angelo Dureghello <[email protected]> > > Cc: Johan Jonker <[email protected]> > > Cc: Sam Protsenko <[email protected]> > > Cc: Guodong Xu <[email protected]> > > Cc: Yao Zi <[email protected]> > > Cc: Rick Chen <[email protected]> > > Cc: Leo <[email protected]> > > Signed-off-by: Eric Chung <[email protected]> > > > > --- > > Alex Elder (1): > > riscv: dts: spacemit: define a SPI controller node > > > > Andre Heider (6): > > riscv: dts: spacemit: k1-musepi-pro: add PMIC and power infrastructure > > riscv: dts: spacemit: k1-musepi-pro: add 24c02 eeprom > > riscv: dts: spacemit: k1-musepi-pro: enable QSPI and add SPI NOR > > riscv: dts: spacemit: k1-musepi-pro: enable USB 3 ports > > riscv: dts: spacemit: k1-musepi-pro: enable PCIe ports > > riscv: dts: spacemit: k1-musepi-pro: set default console baud rate > > > > Eric Chung (9): > > spacemit: k1: select boot device via config registers > > pinctrl: k1: fix pull-up/pull-down configuration > > pinctrl: k1: add IO power domain configuration support > > mmc: k1: add sdhci platform driver > > dts: k1: enable mmc devices in SPL > > configs: k1: enable SD and eMMC support > > MAINTAINER: update Spacemit K1 entry > > doc: spacemit: flash on K1 SoC based boards > > spacemit: k1: fix product name detection and DTB matching in SPL > > > > Iker Pedrosa (2): > > riscv: dts: spacemit: k1: add SD card controller and pinctrl support > > riscv: dts: spacemit: k1-bananapi-f3: add SD card support with UHS > > modes > > I am just curious, is there a particular reason why the device-tree > changes for the OrangePi RV2 aren't included in this series? >
I only fetch the patches I could verify, as I only have the musepi pro and bananpi f3. Other patches I'll leave to the maintainer.
