You must have already DFS enabled in that rocket. Mike is talking about an
older rocket before DFS was approved on the rockets.
I ran into the same issue trying to use the 5240. I upgraded directly to
5.5.10 and no DFS nor 5160-5240 was avalable. I downgraded checked the uni box
entered my codes and voila when I upgraded to 5.5.10 there was the 5160-5240.
(eventhought those are not DFS :-)
----- Original Message -----
From: Josh Luthman
To: Ubiquiti Users Group
Sent: Sunday, December 07, 2014 5:17 PM
Subject: Re: [Ubnt_users] Old Rockets, weird problems
I just upgraded a pair of Rockets to 5.5.10 and was able to enable DFS.
Josh Luthman
Office: 937-552-2340
Direct: 937-552-2343
1100 Wayne St
Suite 1337
Troy, OH 45373
On Dec 7, 2014 8:11 PM, "Jason Bailey" <j284...@yahoo.com> wrote:
Going back to 5.5.8 and clicking the uni-2 box on the system page will get
you there.
On Sunday, December 7, 2014 8:08 PM, Kees H <wi...@calbroadband.com> wrote:
You have to downgrade the software ( I think it was 5.5.4 that had the DFS
key) then enter the dfs key and then upgrade.
----- Original Message -----
From: Mike Hammett
To: Ubiquiti Users Group
Sent: Sunday, December 07, 2014 11:00 AM
Subject: Re: [Ubnt_users] Old Rockets, weird problems
I believe that has been done.
Definitely the reboot both sides.
The DFS checkbox\fields are definitely not there.
-----
Mike Hammett
Intelligent Computing Solutions
http://www.ics-il.com
--------------------------------------------------------------------------
From: "Josh Luthman" <j...@imaginenetworksllc.com>
To: "Ubiquiti Users Group" <ubnt_users@wispa.org>
Sent: Sunday, December 7, 2014 12:47:46 PM
Subject: Re: [Ubnt_users] Old Rockets, weird problems
Old rocket, plug in DFS credentials for your company, reboot BOTH SIDES.
BOTH.
Josh Luthman
Office: 937-552-2340
Direct: 937-552-2343
1100 Wayne St
Suite 1337
Troy, OH 45373
On Dec 7, 2014 1:45 PM, "Mike Hammett" <wispaubntus...@ics-il.net> wrote:
I have some old Rockets (maybe 5.2.1 vintage?). I upgraded them as
needed throughout the years. The past day or two, performance in on part of the
network has been erratic to say the best of it.
I noticed that they were in Compliance Test mode, but didn't have the
input boxes for the DFS stuff, so I must have entered it at one point, but
never actually moved over. They were on 5.5.2.
Don't fuck with what works. Well, now it's not working right.
I upgrade to 5.5.4, then 5.5.10. I set the country code to US.... no
DFS channels show up on the AP.
Do I need to reboot it after setting it to US so that I can get the DFS
channels?
A reset to defaults and starting over is kinda out of the question at
the moment.
Any other ideas?
If I have to climb to replace radios, ePMPs are going up instead.
-----
Mike Hammett
Intelligent Computing Solutions
http://www.ics-il.com
_______________________________________________
Ubnt_users mailing list
Ubnt_users@wispa.org
http://lists.wispa.org/mailman/listinfo/ubnt_users
_______________________________________________
Ubnt_users mailing list
Ubnt_users@wispa.org
http://lists.wispa.org/mailman/listinfo/ubnt_users
--------------------------------------------------------------------------
_______________________________________________
Ubnt_users mailing list
Ubnt_users@wispa.org
http://lists.wispa.org/mailman/listinfo/ubnt_users
_______________________________________________
Ubnt_users mailing list
Ubnt_users@wispa.org
http://lists.wispa.org/mailman/listinfo/ubnt_users
_______________________________________________
Ubnt_users mailing list
Ubnt_users@wispa.org
http://lists.wispa.org/mailman/listinfo/ubnt_users
------------------------------------------------------------------------------
_______________________________________________
Ubnt_users mailing list
Ubnt_users@wispa.org
http://lists.wispa.org/mailman/listinfo/ubnt_users
_______________________________________________
Ubnt_users mailing list
Ubnt_users@wispa.org
http://lists.wispa.org/mailman/listinfo/ubnt_users
