i answered to quick earlier. i hadn't read back far enough to understand your problem. I'm actually still confused some what your problem is. A ss of your wireless tab of a radio that your talking about would help. So your saying that on a power beam m5 it's set to an auto channel or a channel in the wrong range you normally use after a firmware update to 6.04. Is that right? That doesn't make a lot of sense unless the pbe m5 is the AP as the AP dictates the channel. that's where I'm confused the most.
Sent from my Verizon, Samsung Galaxy smartphone -------- Original message --------From: Jan Van Kort <j.vank...@oregononline.net> Date: 7/26/17 3:36 PM (GMT-06:00) To: ubnt_users@wispa.org Subject: Re: [Ubnt_users] changing channels on me? using pbe-m5-400, 6.04 at present, most of the m5 gear are pbe. Am wondering if the update to 6.04 put any of them into auto channel mode? On 07/26/2017 12:58 PM, Tyson wrote: pretty sure Josh is right on. on the stations that don't have the channels that the newer ones have update the firmware. can't remember what version is the oldest that accepts it, but 5.6.2 kind of rings a bell. we have 6.0.4 and I know that works. to add more channels need to activate UNII rules under the system tab on all our m5 gear so that doesn't happen. Nanostation m5s throw me off the most since they do some eds channels but not all so it's easier to get lucky and work out of the box and forget on them. Sent from my Verizon, Samsung Galaxy smartphone -------- Original message -------- From: Josh Luthman <j...@imaginenetworksllc.com> Date: 7/26/17 3:08 PM (GMT-05:00) To: Ubiquiti Users Group <ubnt_users@wispa.org> Subject: Re: [Ubnt_users] changing channels on me? Are you saying the station's frequency is only doing the upper channels? Depending on which m5 radio it is, you might not have access to 5.1 or 5.4 (pre/post an FCC key...) Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Wed, Jul 26, 2017 at 3:06 PM, Jan Van Kort <j.vank...@oregononline.net> wrote: channel 37 does not have a (DFS) next to it in the list On 07/26/2017 11:55 AM, Josh Luthman wrote: DFS channels it will have to vacate, yes. I suggest setting multiple frequencies on the AP so it cycles through them. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Wed, Jul 26, 2017 at 2:53 PM, Jan Van Kort <j.vank...@oregononline.net> wrote: two issues: I've got some m5 gear that seem able to change channels after install on their own. I've found a couple that were in auto mode (never allowed here) and a few more that were in not normal channel selections. Does this happen as a result of firmware updates? I've noticed on the newer radios they have a wider range of channel selections, but this seems weird as another new one out of same parts order pile won't have the same range. I'll set the access point for channel 37 and go over to the receive station and it won't see it. Cannot connect them, the station will only go to 147. _______________________________________________ Ubnt_users mailing list Ubnt_users@wispa.org http://lists.wispa.org/mailman/listinfo/ubnt_users _______________________________________________ Ubnt_users mailing list Ubnt_users@wispa.org http://lists.wispa.org/mailman/listinfo/ubnt_users _______________________________________________ Ubnt_users mailing list Ubnt_users@wispa.org http://lists.wispa.org/mailman/listinfo/ubnt_users _______________________________________________ Ubnt_users mailing list Ubnt_users@wispa.org http://lists.wispa.org/mailman/listinfo/ubnt_users
_______________________________________________ Ubnt_users mailing list Ubnt_users@wispa.org http://lists.wispa.org/mailman/listinfo/ubnt_users