Use egress only. LAN egress is download, WLAN egress is upload.
On 08/22/2017 08:59 AM, Troy Gibson, Byhalia.net wrote:
Steve,
Thats a good idea to test. Never set one up on the CPE. I see the
area on the network tab, but not 100% how to set up and down limits on
it. Is there a protocol to use so the settings function correctly?
Thanks,
Troy
Sent from my Verizon, Samsung Galaxy smartphone
-------- Original message --------
From: Steve Barnes <st...@pcswin.com>
Date: 8/21/17 10:40 PM (GMT-05:00)
To: Ubiquiti Users Group <ubnt_users@wispa.org>
Subject: Re: [Ubnt_users] Erratic downloads and uploads, PBE-M5-400
Try taking the queue off the Mtik and settIng it on the cpe
Steve Barnes
-----Original Message-----
From: ubnt_users-boun...@wispa.org
[mailto:ubnt_users-boun...@wispa.org] On Behalf Of t...@byhalia.net
Sent: Monday, August 21, 2017 2:33 PM
To: ubnt_users@wispa.org
Subject: [Ubnt_users] Erratic downloads and uploads, PBE-M5-400
Time to ask the experts as I cannot figure out this issue!! This CPE
worked perfect until a recent storm, but I have replaced the AP and
CPE radios at this point too.
I have one customer that reports erratic download and uploads.
Actually sometimes going above the set rate in my Tik router,
CCR1009-7G-1C+PC, Firmware Bugfix 6.38.7. This CPE is connected to an
AP that is feed from routers that are directly connected to my fiber
line in my Data Center in this area, so everything is at the base of
the tower that feeds this AP directly, no jumps to other towers first.
I spent a lot of time connected to this CPE at the customers house
testing with and without airmax, changing radio firmware, decreasing
and increasing power, but get the same erratic behavior. I changed
the POE,
M5 cone tested the cable (tested good), but still the same. I finally
tested multiple channels at the AP and found a stable solution/temp
fix, not perfect, but stable. I had to leave the CPE unlimited as it
was still not behaving correctly so for the trouble I left it
unlimited to buy time to figure this out. I even stopped at some
other customers on that same road and AP and those tested like it
should at the rate it was set to in the Tik router.
Customer has been great during this time and sending me samples of
speedtests at different times in the day. Still getting big swings in
speeds that vary and when I check AirControl it does not even match
the speeds they are reporting. I'm using AC 2.1 beta 7. I realize
the unlimited setup could impact their tests, but why is AC2 not
showing anything even close to their speedtests?
Below are the radio stats for this CPE. I attached a word file of the
M5 radio stats as the copied image would not paste correctly on this
email.
Signal: -56dBm
H/V: -59/-58 dBm
Transmit CCQ: 93%
TX/RX: 72.222mbps/72.222mbps
Firmware 5.6.15 XW
Airmax is enabled and shows 96% for both.
Channel Width: 10mhz
Channel Freq: 5805
Distance is 1.7 miles
TX power 26
Access Point is on 5.6.15 XW firmware
Thank you for your support!!
Troy Gibson
Byhalia.net, LLC
_______________________________________________
Ubnt_users mailing list
Ubnt_users@wispa.org
http://lists.wispa.org/mailman/listinfo/ubnt_users
_______________________________________________
Ubnt_users mailing list
Ubnt_users@wispa.org
http://lists.wispa.org/mailman/listinfo/ubnt_users
_______________________________________________
Ubnt_users mailing list
Ubnt_users@wispa.org
http://lists.wispa.org/mailman/listinfo/ubnt_users