The lines from dmesg before I unloaded (rmmod) and reloaded (modprobe) the ath9k module:
[ 110.996294] ath9k: Unable to set channel [ 110.996303] ath9k: Unable to set channel [ 110.996309] ath9k: Unable to set channel [ 110.996313] ath9k: Unable to set channel [ 110.996318] ath9k: Unable to set channel [ 110.996322] ath9k: Unable to set channel [ 110.996327] ath9k: Unable to set channel [ 110.996331] ath9k: Unable to set channel [ 110.996336] ath9k: Unable to set channel [ 110.996340] ath9k: Unable to set channel [ 110.996345] ath9k: Unable to set channel [ 110.996349] ath9k: Unable to set channel [ 110.996354] ath9k: Unable to set channel [ 110.996365] ath9k: Unable to set channel Lines from dmesg after I unloaded (rmmod) and reloaded (modprobe) the ath9k module: [ 126.205294] ath9k: Device not present [ 126.250315] ath9k 0000:09:00.0: PCI INT A disabled [ 126.250408] ath9k: Driver unloaded [ 126.301546] ath9k 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 126.301638] ath9k 0000:09:00.0: setting latency timer to 64 [ 126.356917] ath: EEPROM regdomain: 0x6a [ 126.356924] ath: EEPROM indicates we should expect a direct regpair map [ 126.356932] ath: Country alpha2 being used: 00 [ 126.356936] ath: Regpair used: 0x6a [ 126.366697] phy1: Selected rate control algorithm 'ath9k_rate_control' [ 126.370712] Registered led device: ath9k-phy1::radio [ 126.371750] Registered led device: ath9k-phy1::assoc [ 126.372970] Registered led device: ath9k-phy1::tx [ 126.375130] Registered led device: ath9k-phy1::rx [ 126.375206] phy1: Atheros AR9285 MAC/BB Rev:2 AR5133 RF Rev:e0: mem=0xfa300000, irq=18 [ 126.443956] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 133.486497] wlan0: deauthenticating from 00:1c:4a:47:59:f1 by local choice (reason=3) [ 133.497826] wlan0: direct probe to AP 00:1c:4a:47:59:f1 (try 1) [ 133.501704] wlan0: direct probe responded [ 133.501717] wlan0: authenticate with AP 00:1c:4a:47:59:f1 (try 1) [ 133.504170] wlan0: authenticated [ 133.504225] wlan0: associate with AP 00:1c:4a:47:59:f1 (try 1) [ 133.513093] wlan0: RX AssocResp from 00:1c:4a:47:59:f1 (capab=0x411 status=0 aid=3) [ 133.513101] wlan0: associated [ 133.513704] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 133.584926] padlock: VIA PadLock not detected. [ 134.870055] martian source 255.255.255.255 from 192.168.8.1, on dev wlan0 [ 134.870061] ll header: ff:ff:ff:ff:ff:ff:00:1c:4a:96:7a:91:08:00 [ 144.200287] wlan0: no IPv6 routers present [ 331.374744] cfg80211: Found new beacon on frequency: 2472 MHz (Ch 13) on phy1 -- Wireless and Bluetooth switch does not work correctly on lenovo ideapad s10-3 https://bugs.launchpad.net/bugs/577114 You received this bug notification because you are a member of Ubuntu Bugs, which is subscribed to Ubuntu. -- ubuntu-bugs mailing list ubuntu-bugs@lists.ubuntu.com https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs