Насколько я понимаю, посыпался хард- 196 Reallocated_Event_Count 0x0032 159 159 000 Old_age Always - 41 эта надпись говорит о том, что 41 раз происходила замена битых секторов. Если это число будет расти - меняйте хард.
2008/2/6, sergicus s <[EMAIL PROTECTED]>: > > Недавно постаил на сервер ubuntu 7.1- server > потихоньку с ней работал > начал проверять smart > > sudo smartctl -a /dev/hda > > smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen > Home page is http://smartmontools.sourceforge.net/ > > === START OF INFORMATION SECTION === > Model Family: Western Digital Caviar family > Device Model: WDC WD600BB-00CAA1 > Serial Number: WD-WMA8E7857660 > Firmware Version: 17.07W17 > User Capacity: 60 022 480 896 bytes > Device is: In smartctl database [for details use: -P show] > ATA Version is: 5 > ATA Standard is: Exact ATA specification draft version not indicated > Local Time is: Wed Feb 6 09:59:53 2008 MSK > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > See vendor-specific Attribute list for marginal Attributes. > > General SMART Values: > Offline data collection status: (0x84) Offline data collection activity > was suspended by an interrupting > command from host. > Auto Offline Data Collection: > Enabled. > Self-test execution status: ( 0) The previous self-test routine > completed > without error or no self-test has > ever > been run. > Total time to complete Offline > data collection: (2340) seconds. > Offline data collection > capabilities: (0x3b) SMART execute Offline immediate. > Auto Offline data collection > on/off support. > Suspend Offline collection upon > new > command. > Offline surface scan supported. > Self-test supported. > Conveyance Self-test supported. > No Selective Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before entering > power-saving mode. > Supports SMART auto save timer. > Error logging capability: (0x01) Error logging supported. > No General Purpose Logging > support. > Short self-test routine > recommended polling time: ( 2) minutes. > Extended self-test routine > recommended polling time: ( 43) minutes. > Conveyance self-test routine > recommended polling time: ( 5) minutes. > > SMART Attributes Data Structure revision number: 16 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED > WHEN_FAILED RAW_VALUE > 1 Raw_Read_Error_Rate 0x000b 200 001 051 Pre-fail Always > In_the_past 0 > 3 Spin_Up_Time 0x0007 100 094 021 Pre-fail > Always - 4058 > 4 Start_Stop_Count 0x0032 100 100 040 Old_age > Always - 372 > 5 Reallocated_Sector_Ct 0x0033 180 180 140 Pre-fail > Always - 316 > 7 Seek_Error_Rate 0x000b 100 253 051 Pre-fail > Always - 0 > 9 Power_On_Hours 0x0032 050 050 000 Old_age > Always - 36921 > 10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail > Always - 0 > 11 Calibration_Retry_Count 0x0013 100 100 051 Pre-fail > Always - 0 > 12 Power_Cycle_Count 0x0032 100 100 000 Old_age > Always - 220 > 196 Reallocated_Event_Count 0x0032 159 159 000 Old_age > Always - 41 > 197 Current_Pending_Sector 0x0012 189 186 000 Old_age > Always - 108 > 198 Offline_Uncorrectable 0x0012 189 188 000 Old_age > Always - 108 > 199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age > Always - 65 > 200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail > Offline - 0 > > SMART Error Log Version: 1 > ATA Error Count: 5945 (device log contains only the most recent five > errors) > CR = Command Register [HEX] > FR = Features Register [HEX] > SC = Sector Count Register [HEX] > SN = Sector Number Register [HEX] > CL = Cylinder Low Register [HEX] > CH = Cylinder High Register [HEX] > DH = Device/Head Register [HEX] > DC = Device Command Register [HEX] > ER = Error register [HEX] > ST = Status register [HEX] > Powered_Up_Time is measured from power on, and printed as > DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, > SS=sec, and sss=millisec. It "wraps" after 49.710 days. > > Error 5945 occurred at disk power-on lifetime: 1020 hours (42 days + 12 > hours) > When the command that caused the error occurred, the device was doing > SMART Offline or Self-test. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 40 51 10 63 0c 39 e2 Error: UNC at LBA = 0x02390c63 = 37293155 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name > -- -- -- -- -- -- -- -- ---------------- -------------------- > 40 00 10 5f 0c 39 e2 00 11:01:39.800 READ VERIFY SECTOR(S) > 40 00 10 4f 0c 39 e2 00 11:01:39.800 READ VERIFY SECTOR(S) > 40 00 20 2f 12 39 e2 00 11:01:39.750 READ VERIFY SECTOR(S) > 40 00 20 0f 12 39 e2 00 11:01:36.900 READ VERIFY SECTOR(S) > 40 00 20 2f 0f 39 e2 00 11:01:34.200 READ VERIFY SECTOR(S) > > Error 5944 occurred at disk power-on lifetime: 1020 hours (42 days + 12 > hours) > When the command that caused the error occurred, the device was doing > SMART Offline or Self-test. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 40 51 20 15 12 39 e2 Error: UNC at LBA = 0x02391215 = 37294613 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name > -- -- -- -- -- -- -- -- ---------------- -------------------- > 40 00 20 0f 12 39 e2 00 11:01:36.900 READ VERIFY SECTOR(S) > 40 00 20 2f 0f 39 e2 00 11:01:34.200 READ VERIFY SECTOR(S) > 40 00 20 0f 0f 39 e2 00 11:01:34.200 READ VERIFY SECTOR(S) > 40 00 20 6f 0c 39 e2 00 11:01:34.200 READ VERIFY SECTOR(S) > 40 00 20 4f 0c 39 e2 00 11:01:31.500 READ VERIFY SECTOR(S) > > Error 5943 occurred at disk power-on lifetime: 1020 hours (42 days + 12 > hours) > When the command that caused the error occurred, the device was doing > SMART Offline or Self-test. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 40 51 20 3c 0f 39 e2 Error: UNC at LBA = 0x02390f3c = 37293884 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name > -- -- -- -- -- -- -- -- ---------------- -------------------- > 40 00 20 2f 0f 39 e2 00 11:01:34.200 READ VERIFY SECTOR(S) > 40 00 20 0f 0f 39 e2 00 11:01:34.200 READ VERIFY SECTOR(S) > 40 00 20 6f 0c 39 e2 00 11:01:34.200 READ VERIFY SECTOR(S) > 40 00 20 4f 0c 39 e2 00 11:01:31.500 READ VERIFY SECTOR(S) > 40 00 40 4f 12 39 e2 00 11:01:31.500 READ VERIFY SECTOR(S) > > Error 5942 occurred at disk power-on lifetime: 1020 hours (42 days + 12 > hours) > When the command that caused the error occurred, the device was doing > SMART Offline or Self-test. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 40 51 20 63 0c 39 e2 Error: UNC at LBA = 0x02390c63 = 37293155 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name > -- -- -- -- -- -- -- -- ---------------- -------------------- > 40 00 20 4f 0c 39 e2 00 11:01:31.500 READ VERIFY SECTOR(S) > 40 00 40 4f 12 39 e2 00 11:01:31.500 READ VERIFY SECTOR(S) > 40 00 40 0f 12 39 e2 00 11:01:28.950 READ VERIFY SECTOR(S) > 40 00 40 4f 0f 39 e2 00 11:01:28.950 READ VERIFY SECTOR(S) > 40 00 40 0f 0f 39 e2 00 11:01:26.300 READ VERIFY SECTOR(S) > > Error 5941 occurred at disk power-on lifetime: 1020 hours (42 days + 12 > hours) > When the command that caused the error occurred, the device was doing > SMART Offline or Self-test. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 40 51 40 15 12 39 e2 Error: UNC at LBA = 0x02391215 = 37294613 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name > -- -- -- -- -- -- -- -- ---------------- -------------------- > 40 00 40 0f 12 39 e2 00 11:01:28.950 READ VERIFY SECTOR(S) > 40 00 40 4f 0f 39 e2 00 11:01:28.950 READ VERIFY SECTOR(S) > 40 00 40 0f 0f 39 e2 00 11:01:26.300 READ VERIFY SECTOR(S) > 40 00 40 4f 0c 39 e2 00 11:01:23.650 READ VERIFY SECTOR(S) > 40 00 40 0f 0c 39 e2 00 11:01:23.650 READ VERIFY SECTOR(S) > > SMART Self-test log structure revision number 1 > No self-tests have been logged. [To run self-tests, use: smartctl -t] > > > Device does not support Selective Self Tests/Logging > > > > Вывелись ошибки - посоветуйте что они значат > > > -- > С уважением > Сергей > -- > ubuntu-ru mailing list > ubuntu-ru@lists.ubuntu.com > https://lists.ubuntu.com/mailman/listinfo/ubuntu-ru > >
-- ubuntu-ru mailing list ubuntu-ru@lists.ubuntu.com https://lists.ubuntu.com/mailman/listinfo/ubuntu-ru
