Как и обещал даю вывод:
r...@lorderon:~# xrandr
Screen 0: minimum 320 x 240, current 1280 x 1024, maximum 1280 x 1024
default connected 1280x1024+0+0 0mm x 0mm
*1280x1024 60.0 75.0* 56.0 *
1280x960 60.0
1152x864 75.0 70.0 60.0
1024x768 75.0 70.0 60.0
960x600 60.0
960x540 60.0
840x525 70.0 60.0
832x624 75.0
800x600 75.0 72.0 60.0 56.0 65.0
800x512 60.0
720x450 60.0
700x525 75.0 70.0 60.0
680x384 60.0
640x512 75.0 60.0
640x480 75.0 73.0 60.0
576x432 75.0 70.0 60.0
512x384 75.0 70.0 60.0
416x312 75.0
400x300 75.0 72.0 60.0 56.0
320x240 75.0 73.0 60.0
r...@lorderon:~#
Отсюда я понимаю что работает он на 60Гц. Т.е. OSD меня не обманывал, верно?
r...@lorderon:~# cat /proc/driver/nvidia/version
NVRM version: NVIDIA UNIX x86 Kernel Module 180.44 Mon Mar 23 14:59:10 PST
2009
GCC version: gcc version 4.3.3 (Ubuntu 4.3.3-5ubuntu4)
r...@lorderon:~#
Далее:
r...@lorderon:~# get-edid|parse-edid
parse-edid: parse-edid version 1.4.1
get-edid: get-edid version 1.4.1
Performing real mode VBE call
Interrupt 0x10 ax=0x4f00 bx=0x0 cx=0x0
Function supported
Call successful
VBE version 300
VBE string at 0x11110 "NVIDIA"
VBE/DDC service about to be called
Report DDC capabilities
Performing real mode VBE call
Interrupt 0x10 ax=0x4f15 bx=0x0 cx=0x0
Function supported
Call successful
Monitor and video card combination does not support DDC1 transfers
Monitor and video card combination supports DDC2 transfers
0 seconds per 128 byte EDID block transfer
Screen is not blanked during DDC transfer
Reading next EDID block
VBE/DDC service about to be called
Read EDID
Performing real mode VBE call
Interrupt 0x10 ax=0x4f15 bx=0x1 cx=0x0
Function supported
Call failed
The EDID data should not be trusted as the VBE call failed
EDID claims 255 more blocks left
EDID blocks left is wrong.
Your EDID is probably invalid.
parse-edid: EDID checksum failed - data is corrupt. Continuing anyway.
parse-edid: first bytes don't match EDID version 1 header
parse-edid: do not trust output (if any).
# EDID version 255 revision 255
Section "Monitor"
Identifier "___:ffff"
VendorName "___"
ModelName "___:ffff"
# DPMS capabilities: Active off:yes Suspend:yes Standby:yes
Mode "4095x4095" # vfreq 9.770Hz, hfreq 80.018kHz
DotClock 655.350000
HTimings 4095 4350 4605 8190
VTimings 4095 4158 4221 8190
Flags "Interlace" "+HSync" "+VSync"
EndMode
Mode "4095x4095" # vfreq 9.770Hz, hfreq 80.018kHz
DotClock 655.350000
HTimings 4095 4350 4605 8190
VTimings 4095 4158 4221 8190
Flags "Interlace" "+HSync" "+VSync"
EndMode
Mode "4095x4095" # vfreq 9.770Hz, hfreq 80.018kHz
DotClock 655.350000
HTimings 4095 4350 4605 8190
VTimings 4095 4158 4221 8190
Flags "Interlace" "+HSync" "+VSync"
EndMode
Mode "4095x4095" # vfreq 9.770Hz, hfreq 80.018kHz
DotClock 655.350000
HTimings 4095 4350 4605 8190
VTimings 4095 4158 4221 8190
Flags "Interlace" "+HSync" "+VSync"
EndMode
EndSection
r...@lorderon:~#
По-моему оно сошло с ума.* Mode "4095x4095*" - хочу монитор с таким
разрешением =)
r...@lorderon:~# ddcprobe
vbe: VESA 3.0 detected.
oem: NVIDIA
vendor: NVIDIA Corporation
product: G84 Board - p402h01 Chip Rev
memory: 14336kb
mode: 640x400x256
mode: 640x480x256
mode: 800x600x16
mode: 800x600x256
mode: 1024x768x16
mode: 1024x768x256
mode: 1280x1024x16
mode: 1280x1024x256
mode: 320x200x64k
mode: 320x200x16m
mode: 640x480x64k
mode: 640x480x16m
mode: 800x600x64k
mode: 800x600x16m
mode: 1024x768x64k
mode: 1024x768x16m
mode: 1280x1024x64k
mode: 1280x1024x16m
edid:
edid: 1 3
id: 01bb
eisa: SAM01bb
serial: 48413139
manufacture: 50 2005
input: analog signal.
screensize: 38 30
gamma: 2.200000
dpms: RGB, active off, no suspend, no standby
timing: 720x...@70 Hz (VGA 640x400, IBM)
timing: 720x...@88 Hz (XGA2)
timing: 640x...@60 Hz (VGA)
timing: 640x...@67 Hz (Mac II, Apple)
timing: 640x...@72 Hz (VESA)
timing: 640x...@75 Hz (VESA)
timing: 800x...@60 Hz (VESA)
timing: 800x...@72 Hz (VESA)
timing: 800x...@75 Hz (VESA)
timing: 832x...@75 Hz (Mac II)
timing: 1024x...@87 Hz Interlaced (8514A)
timing: 1024x...@70 Hz (VESA)
timing: 1024x...@75 Hz (VESA)
*timing: 1280x1...@75 (VESA)*
ctiming: 1280x1...@60
ctiming: 1280x...@60
ctiming: 1152x...@75
dtiming: 1280x1...@70
monitorrange: 30-81, 56-75
monitorname: SyncMaster
monitorserial: HSGYC00941
r...@lorderon:~#
Таки я понимаю что мой монитор таки поддерживает желаемый режим
dpkg-reconfigure -plow xserver-xorg - еще вчера пробовал - не помогло =(
Сейчас попробую установить драйвер скачанный с сайта.
7 мая 2009 г. 15:12 пользователь Alex Berber <[email protected]> написал:
> Led пишет:
> > Но OSD монитора по прежнему говорит что нет, у Вас 60Гц. Нет, это не
> > проблема хардварная, в Windows 7 все отлично работает на 75Гц.
> Скорее всего OSD монитора попросту врет, у меня тоже GeForce 8600 и еще
> с 7.04 никаких проблем не испытываю.
>
> Опубликуйте пожалуйста выводы следующих команд.
>
> $ xrandr
>
> $ cat /proc/driver/nvidia/version
>
> К тому же из лога r...@lorderon:~# tail /var/log/Xorg.0.log
> ........
> (II) NVIDIA(0): Setting mode "1280x1024_75"
> .......
>
> фактически видно что при разрешениии 1280х1024 у вас 75 герц.
>
> Ждем вывода.
>
> Алекс.
>
>
>
> --
> ubuntu-ru mailing list
> [email protected]
> https://lists.ubuntu.com/mailman/listinfo/ubuntu-ru
>
--
with best regards, Aliaksei Marchuk
--
ubuntu-ru mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-ru
