Thank you
Yes, I am using LACP bond on Gi0/11-12 for public and guest, I setup the
traffice labes on XenServer and when configuring CS public-guest, I am using
Ubuntu, do I need the cloudbro and cloudbr1?
I will try removing
Switchport mode access
From: Imran Ahmed <im...@eaxiom.net>
To: users@cloudstack.apache.org
Sent: Saturday, September 9, 2017 12:59 AM
Subject: RE: Configuring CS with Advance Networking for an internal laboratory
I don’t think you need this line at least:
Switchport mode access
I assume that you use the LACP bond that bonds interfaces: Gi0/11 and Gi0/12
to carry both public traffic as well as guest traffic.
The next factor is the traffic labels you set in your Cloudstack advanced
zone setup .
Another factor is the configuration of cloudbro and Cloudbr1 bridges in
your interface configurations.
By the way are you using CentOS or Ubuntu or Suse or ..?
Regards,
Imran
-----Original Message-----
From: Luis [mailto:lmartinez...@yahoo.com.INVALID]
Sent: Saturday, September 09, 2017 9:07 AM
To: users@cloudstack.apache.org
Cc: Paul Angus
Subject: Re: Configuring CS with Advance Networking for an internal laboratory
Hi
I am testing my CS with Advance Networking but it's not able to download iso or
the templates, I think this is because of my VLAN configuration, s-vm or v-vm
can't ping to internet, I did set up this parameter
(secstorage.allowed.internal.sites) to my manager and host ip.
This is my VLAN configuration, please any advice on this issue
conf tinterface range Gi0/11-12switchport trunk encapsulation dot1q switchport
mode trunkswitchport trunk allowed vlan 65,300-800switchport mode
accesschannel-group 4 mode activechannel-protocol lacpend
Thank you
From: Sateesh Chodapuneedi <sateesh.chodapune...@accelerite.com>
To: Luis <lmartinez...@yahoo.com>; "users@cloudstack.apache.org"
<users@cloudstack.apache.org>
Cc: Paul Angus <paul.an...@shapeblue.com>
Sent: Friday, September 8, 2017 10:48 AM
Subject: Re: Configuring CS with Advance Networking for an internal laboratory
Hi Luis,
>.Do I need to specify what port the vlan are going to use?
Yes, selection of interfaces/ports need to be done. Please add command
“interface range Gi0/9 – 10” after command “conf t”
Also add “no switchport mode access” just before the command “end”
Hope that helps.
Regards,
Sateesh Chodapuneedi,
CloudStack Development,
Engineering, http://accelerite.com<http://accelerite.com/>
Santa Clara, 95054, CA
@accelerite
From: Luis <lmartinez...@yahoo.com>
Reply-To: Luis <lmartinez...@yahoo.com>
Date: Friday, 8 September 2017 at 8:00 PM
To: Sateesh Chodapuneedi <sateesh.chodapune...@accelerite.com>,
"users@cloudstack.apache.org" <users@cloudstack.apache.org>
Cc: Paul Angus <paul.an...@shapeblue.com>
Subject: Re: Configuring CS with Advance Networking for an internal laboratory
Thank you for your help
Do I need to specify what port the vlan are going to use?
1.- create vlnas
conf t
vlan 65,300-800
end
2.-
conf t
switchport mode trunk
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 65,300-800
end
________________________________
From: Sateesh Chodapuneedi <sateesh.chodapune...@accelerite.com>
To: "users@cloudstack.apache.org" <users@cloudstack.apache.org>; Luis
<lmartinez...@yahoo.com>
Cc: Paul Angus <paul.an...@shapeblue.com>
Sent: Friday, September 8, 2017 9:42 AM
Subject: Re: Configuring CS with Advance Networking for an internal laboratory
Hi Luis,
I have configured Cisco 3750G switch for my CloudStack advanced mode setup.
Configuration should be the similar for Cisco 3560 as well, probably might help
you.
>> 4 Nics: 2 for Management-Storage (LACP) and 2 for Public-Guest
Make sure to setup the VLANs before configuring the switch ports for interfaces
meant for Public and Guest traffic
conf t
vlan <PUBLIC_VLAN_RANGE>,<ZONE_VLAN_RANGE>
end
Please note that the VLAN range meant for public traffic are routable (with
subnet assigned)
Configure the switch ports for Public and Guest traffic
switchport mode trunk
switchport trunk encapsulation dot1q
switchport trunk allowed vlan <PUBLIC_VLAN_RANGE>,<ZONE_VLAN_RANGE>
Ex: If 100 is VLAN ID of routable VLAN meant for public traffic, and VLAN IDs
500 to 600 are guest (zone) VLANs, then above command looks like,
switchport trunk allowed vlan 100,500-600
Regards,
Sateesh Chodapuneedi,
CloudStack Development,
Engineering, http://accelerite.com<http://accelerite.com/>
Santa Clara, 95054, CA
@accelerite
-----Original Message-----
From: Luis
<lmartinez...@yahoo.com.INVALID<mailto:lmartinez...@yahoo.com.INVALID>>
Reply-To: "users@cloudstack.apache.org<mailto:users@cloudstack.apache.org>"
<users@cloudstack.apache.org<mailto:users@cloudstack.apache.org>>, Luis
<lmartinez...@yahoo.com<mailto:lmartinez...@yahoo.com>>
Date: Friday, 8 September 2017 at 5:39 PM
To: Paul Angus <paul.an...@shapeblue.com<mailto:paul.an...@shapeblue.com>>,
"users@cloudstack.apache.org<mailto:users@cloudstack.apache.org>"
<users@cloudstack.apache.org<mailto:users@cloudstack.apache.org>>
Subject: Re: Configuring CS with Advance Networking for an internal laboratory
Thank you Paul
Your article is really helpful, I think my problem is finding the correct
commands to setup the switch, this is what I have
CS 4.10: on Ubuntu 14.044 nics: 2 for management (LACP) and 2 for Storage
(LACP)
XenServer for host4 Nics: 2 for Management-Storage (LACP) and 2 for
Public-Guest
Is it possible for you or the group to help me with the lines to set up
correctly the Cisco Switch, I will appreciate your help
Cisco Switch 3560Ports: 9 - 10 for Management-storageconf tinterface range
Gi0/9 - 10switchport mode accessno shutchannel-group 3 mode
activechannel-protocol lacpend
Port 11 - 12 for Piblic-Guest
conf tinterface range Gi0/11 - 12switchport mode accessno shutchannel-group
4 mode activechannel-protocol lacpend From: Paul Angus
<paul.an...@shapeblue.com<mailto:paul.an...@shapeblue.com>>
To: "users@cloudstack.apache.org<mailto:users@cloudstack.apache.org>"
<users@cloudstack.apache.org<mailto:users@cloudstack.apache.org>>; Luis
<lmartinez...@yahoo.com<mailto:lmartinez...@yahoo.com>>
Sent: Friday, September 8, 2017 5:19 AM
Subject: RE: Configuring CS with Advance Networking for an internal
laboratory
Luis,
You may find this blog from yester-year helpful:
http://www.shapeblue.com/understanding-cloudstacks-physical-networking-architecture/
Kind regards,
Paul Angus
paul.an...@shapeblue.com<mailto:paul.an...@shapeblue.com>
www.shapeblue.com
53 Chandos Place, Covent Garden, London WC2N 4HSUK
@shapeblue
-----Original Message-----
From: Paul Angus
[mailto:paul.an...@shapeblue.com<mailto:paul.an...@shapeblue.com>]
Sent: 07 September 2017 22:12
To: Luis <lmartinez...@yahoo.com<mailto:lmartinez...@yahoo.com>>;
users@cloudstack.apache.org<mailto:users@cloudstack.apache.org>
Subject: RE: Configuring CS with Advance Networking for an internal
laboratory
No problem Luis,
1. Advanced networking replies on VLANs (or some SDN isolation method),
so you need at have a range of VLANs free, that you tell CloudStack that it can
use.
2. The IP ranges I described were only an example you can you any range
you like, but ‘public’ traffic generally is going to require a gateway in order
to ‘go’ somewhere.
3. I looks to me like you are setting all of your interfaces as access
ports. You’ll need ports which deal with multiple VLANs (like ones used for
guest networks) to be trunk ports – with the VLANs which are allowed matching
those that you have told CloudStack that it can use.
Kind regards,
Paul Angus
paul.an...@shapeblue.com<mailto:paul.an...@shapeblue.com>
www.shapeblue.com
53 Chandos Place, Covent Garden, London WC2N 4HSUK @shapeblue
From: Luis [mailto:lmartinez...@yahoo.com<mailto:lmartinez...@yahoo.com>]
Sent: 07 September 2017 20:32
To: Paul Angus <paul.an...@shapeblue.com<mailto:paul.an...@shapeblue.com>>;
users@cloudstack.apache.org<mailto:users@cloudstack.apache.org>
Subject: Re: Configuring CS with Advance Networking for an internal
laboratory
thank you for your help, I have some questions if you can help me to answer
this
1.- can i not use VLAN's for Advance Networking or are necessary for the
configuration
2.- Do I need to create an extra server ans use it as gateway for this
range of IP's?
3.- this is what I am using to create my vlan's on a Cisco 3560, is this
correct?
conf t
interface range Gi0/9 - 10
switchport mode access
no shut
switchport access vlan 65
channel-group 3 mode active
channel-protocol lacp
end
Thank you for your help
________________________________
From: Paul Angus
<paul.an...@shapeblue.com<mailto:paul.an...@shapeblue.com><mailto:paul.an...@shapeblue.com<mailto:paul.an...@shapeblue.com>>>
To:
"users@cloudstack.apache.org<mailto:users@cloudstack.apache.org><mailto:users@cloudstack.apache.org<mailto:users@cloudstack.apache.org>>"
<users@cloudstack.apache.org<mailto:users@cloudstack.apache.org><mailto:users@cloudstack.apache.org<mailto:users@cloudstack.apache.org>>>;
Luis
<lmartinez...@yahoo.com<mailto:lmartinez...@yahoo.com><mailto:lmartinez...@yahoo.com<mailto:lmartinez...@yahoo.com>>>
Sent: Thursday, September 7, 2017 3:05 PM
Subject: RE: Configuring CS with Advance Networking for an internal
laboratory
Hi Luis,
You can give CloudStack a range of RFC1918 addresses (ie private addresses)
to act as an 'internal' public network.
10.0.1.10 - 10.0.1.30
GW: 10.0.1.254
Netmask - 255.255.255.0
If the gateway at 10.0.1.254 can route to the outside world then CloudStack
will still be able to download templates, if not you can always register a
template which you are hosting on an internal network.
If you do the second option ensure that the global setting
'secstorage.allowed.internal.sites' includes the hosting server's IP address.
Kind regards,
Paul Angus
paul.an...@shapeblue.com<mailto:paul.an...@shapeblue.com><mailto:paul.an...@shapeblue.com<mailto:paul.an...@shapeblue.com>>
www.shapeblue.com<http://www.shapeblue.com<http://www.shapeblue.com/>>
53 Chandos Place, Covent Garden, London WC2N 4HSUK @shapeblue
-----Original Message-----
From: Luis
[mailto:lmartinez...@yahoo.com.INVALID<mailto:lmartinez...@yahoo.com.INVALID><mailto:lmartinez...@yahoo.com.INVALID<mailto:lmartinez...@yahoo.com.INVALID>>]
Sent: 07 September 2017 18:42
To: Users
<users@cloudstack.apache.org<mailto:users@cloudstack.apache.org><mailto:users@cloudstack.apache.org<mailto:users@cloudstack.apache.org>>>
Subject: Configuring CS with Advance Networking for an internal laboratory
Hi
I am configuring CS with Advance Networking for internal use without
rotatable IP's, this is for testing and lean CS Advance Networking, This is
what I have CS 4.10XenServer 7.0FreeNas CS is already installed but I can't
download any iso because V-Router can't ping outside my network, any advice?
Public IP:209.229.131.0Internal IP: 10.0.0.0 Thank you for your help.
DISCLAIMER
==========
This e-mail may contain privileged and confidential information which is the
property of Accelerite, a Persistent Systems business. It is intended only for
the use of the individual or entity to which it is addressed. If you are not
the intended recipient, you are not authorized to read, retain, copy, print,
distribute or use this message. If you have received this communication in
error, please notify the sender and delete all copies of this message.
Accelerite, a Persistent Systems business does not accept any liability for
virus infected mails.
