Hello Jermaine,
Long story short:
1. Install XCP-NG 8.2
1.1. Make a a note of the name of the interface OR bond that is
going to be used for management traffic (this can be seen when you go to
CLUSTER -> networking tab
1.2. Make a note of the name of the interface OR bond that is
going to be used for user/public traffic if it is different then the management
For example I use ETH0 for management and have bonded eth2 and eth3 and
use that bond for Public and user traffic - https://imgur.com/nbV2aAu
So the labels here are MGMT and DATA.
2. If you use presetup storage (for example fiber) attach it as you
usually do to the XCP cluster and note the name of the LUN in XenCenter.
3. Install Cloudstack somewhere (4.15) and deploy a zone by filling up
the guide from start to end using the interface labels and the LUN name for
primary storage.
4. Launch the zone deployment and wait for it to fail.
5. Cancel the wizard and go to Infrastruture tab. You will see that
Zone, Pod, cluster and hosts are deployed.
6. select primary storage tab. Add new one with presetup type and fill
in the storage LUN name. It will be added properly.
7. Deploy secondary storage (it was not deployed initially because the
zone wizard was interrupted before that step)
You environment is now ready!
Note: the deployment guide should be edited as it says XenServer switch
needs to be in bridge mode in order the system to work which is not correct as
ACS fully supports OVS.
May be bridge mode is required for some specific network design setting
which I am not aware of at the moment.
Best regards,
Jordan
-----Original Message-----
From: Jermaine Kendall <[email protected]>
Sent: Friday, June 25, 2021 10:49 PM
To: [email protected]
Subject: Re: XCP-NG 8.2 LTS
[X] This message came from outside your organization
On 2021/05/05 09:50:58, Andrija Panic <[email protected]> wrote:
> If you use officially unsupported hypevisor with 4.14 (XCP-ng 8.2),
> you will be missing the records in the guest_os_hypervisor table, and
> that means your VMs would be i.e. started as PV instead of HVM etc.
>
> Be warned :)
>
> Best,
> Andrija
>
> On Wed, 5 May 2021 at 09:09, Yordan Kostov <[email protected]> wrote:
>
> > One more problem is that if you deploy a zone with presetup storage
> > it will give an error when it is at the step when the storage is configured.
> > It is already fixed in 4.15.1:
> >
> > https://urldefense.com/v3/__https://github.com/apache/cloudstack/pul
> > l/4845__;!!A6UyJA!xbgZNCFeV-go7cGrUjQ---_MlaAER2Fdumg-cMdW4msQVKLQOh
> > yt15t8yi-mQoUBNEaGjZ6RgICA$
> >
> > Best regards,
> > Jordan
> >
> > -----Original Message-----
> > From: Dominik Czerepiński <[email protected]>
> > Sent: Tuesday, May 4, 2021 3:06 PM
> > To: [email protected]
> > Subject: Re: XCP-NG 8.2 LTS
> >
> >
> > [X] This message came from outside your organization
> >
> >
> > Me. Works stable. One problem is if You don’t use SSL for
> > consoleproxy change noVNC to older version.
> >
> > Wysłane z iPhone'a
> >
> > > Wiadomość napisana przez Matheus Fontes <[email protected]> w
> > > dniu
> > 04.05.2021, o godz. 03:18:
> > >
> > > I saw in cloudstack 4.15 documentation that it supports xcp-ng
> > > 8.1 Does someone tried 8.2 LTS version?
> > >
> > > thanks
> > > Matheus Fontes
> >
>
>
> --
>
> Andrija Panić
> Hi, I have a few questions with regard to setting up xcp-ng with cloudstack,
> I have never been successful so far. I followed the xenserver hypervisor
> setup and ran into some issues. Do you have any instructions specifically for
> setting up XCP-NG with cloudstack? Also is the CSP package needed for XCP-NG
> becuase the download link is no longer available. The network labels, are
> they necessary and why can't I use the default networking for XCP-NG which is
> OVS?
