Its on my to-do list to update it. Best regards, Jordan
-----Original Message----- From: Jermaine Kendall <jermainekendall5...@gmail.com> Sent: Friday, June 25, 2021 11:46 PM To: users@cloudstack.apache.org Subject: Re: RE: XCP-NG 8.2 LTS [X] This message came from outside your organization Thank you for the reply. It is very much appreciated. Can the documentation be upgraded for XCP-NG hypervisor setup and let me know it's done On 2021/06/25 20:33:08, Yordan Kostov <yord...@nsogroup.com> wrote: > Hello Jermaine, > > Long story short: > 1. Install XCP-NG 8.2 > 1.1. Make a a note of the name of the interface OR bond that is > going to be used for management traffic (this can be seen when you go to > CLUSTER -> networking tab > 1.2. Make a note of the name of the interface OR bond that is > going to be used for user/public traffic if it is different then the > management > For example I use ETH0 for management and have bonded eth2 and eth3 and > use that bond for Public and user traffic - > https://urldefense.com/v3/__https://imgur.com/nbV2aAu__;!!A6UyJA!wDUMW6z5oiy9Dn5sjnQg0lEHza62apzb8T-x4oNAB42Sh99wLL6e3w9RjmN59FNHoLQ2vcyqdMZ2$ > So the labels here are MGMT and DATA. > 2. If you use presetup storage (for example fiber) attach it as you > usually do to the XCP cluster and note the name of the LUN in XenCenter. > 3. Install Cloudstack somewhere (4.15) and deploy a zone by filling up > the guide from start to end using the interface labels and the LUN name for > primary storage. > 4. Launch the zone deployment and wait for it to fail. > 5. Cancel the wizard and go to Infrastruture tab. You will see that > Zone, Pod, cluster and hosts are deployed. > 6. select primary storage tab. Add new one with presetup type and fill > in the storage LUN name. It will be added properly. > 7. Deploy secondary storage (it was not deployed initially > because the zone wizard was interrupted before that step) > > You environment is now ready! > > Note: the deployment guide should be edited as it says XenServer switch > needs to be in bridge mode in order the system to work which is not correct > as ACS fully supports OVS. > May be bridge mode is required for some specific network design setting > which I am not aware of at the moment. > > Best regards, > Jordan > > > -----Original Message----- > From: Jermaine Kendall <jermainekendall5...@gmail.com> > Sent: Friday, June 25, 2021 10:49 PM > To: users@cloudstack.apache.org > Subject: Re: XCP-NG 8.2 LTS > > > [X] This message came from outside your organization > > > On 2021/05/05 09:50:58, Andrija Panic <andrija.pa...@gmail.com> wrote: > > If you use officially unsupported hypevisor with 4.14 (XCP-ng 8.2), > > you will be missing the records in the guest_os_hypervisor table, > > and that means your VMs would be i.e. started as PV instead of HVM etc. > > > > Be warned :) > > > > Best, > > Andrija > > > > On Wed, 5 May 2021 at 09:09, Yordan Kostov <yord...@nsogroup.com> wrote: > > > > > One more problem is that if you deploy a zone with presetup > > > storage it will give an error when it is at the step when the storage is > > > configured. > > > It is already fixed in 4.15.1: > > > > > > https://urldefense.com/v3/__https://github.com/apache/cloudstack/p > > > ul > > > l/4845__;!!A6UyJA!xbgZNCFeV-go7cGrUjQ---_MlaAER2Fdumg-cMdW4msQVKLQ > > > Oh > > > yt15t8yi-mQoUBNEaGjZ6RgICA$ > > > > > > Best regards, > > > Jordan > > > > > > -----Original Message----- > > > From: Dominik Czerepiński <dominato...@gmail.com> > > > Sent: Tuesday, May 4, 2021 3:06 PM > > > To: users@cloudstack.apache.org > > > Subject: Re: XCP-NG 8.2 LTS > > > > > > > > > [X] This message came from outside your organization > > > > > > > > > Me. Works stable. One problem is if You don’t use SSL for > > > consoleproxy change noVNC to older version. > > > > > > Wysłane z iPhone'a > > > > > > > Wiadomość napisana przez Matheus Fontes <math...@ghz.com.br> w > > > > dniu > > > 04.05.2021, o godz. 03:18: > > > > > > > > I saw in cloudstack 4.15 documentation that it supports xcp-ng > > > > 8.1 Does someone tried 8.2 LTS version? > > > > > > > > thanks > > > > Matheus Fontes > > > > > > > > > -- > > > > Andrija Panić > > Hi, I have a few questions with regard to setting up xcp-ng with > > cloudstack, I have never been successful so far. I followed the xenserver > > hypervisor setup and ran into some issues. Do you have any instructions > > specifically for setting up XCP-NG with cloudstack? Also is the CSP package > > needed for XCP-NG becuase the download link is no longer available. The > > network labels, are they necessary and why can't I use the default > > networking for XCP-NG which is OVS? >