March 1, 2023 at 7:17 AM, "Alexander Boettcher" <[email protected]> wrote: > Hi, > > On 28.02.23 14:46, dogma--- via users wrote: > > > > > I tried commenting out the graphics-related lines in the GRUB config files > > to see what it might display. But I just got "Booting 'Genode on NOVA'" and > > a blinking cursor. Perhaps it relies on GRUB setting up the graphics state > > anyway. > > > > no, the graphical boot mode is not strictly required for Intel based systems. > > Which CPU do you have in your X201, in mine is a Intel (R) Core(TM) i5 CPU M > 520 @ 2.4 GHz, 4GB RAM, 1280x800 resolution.
Intel(R) Core(TM) i5 CPU M 560 @ 2.67GHz also 4GB and 1280x800. > - Can you try another USB stick, just in case ? Still fails. > - You may try to remove the 'iommu' line from the hypervisor module2 boot > entry in grub.cfg, which may make a difference. No change. > - In legacy BIOS boot mode (which seems apply to you), you may also try to > remove the 'novga' commandline from the hypervisor module2. In case something > goes wrong very early, the kernel message may give a hint. (but this will > give you no output from Genode system itself) No change. > - If nothings helps, we would need a log of your system to assist further. > -- You may try to setup the report_dump component [0], which would dump all > logs kept in memory to your USB stick, if the system comes up far enough. > However, this would require another machine, where Sculpt OS boots up fine > and you can configure it according to [0]. I was able to boot it on a Latitude E6440, and, improbably enough for an utter novice, actually got the report_dump working so that when I boot on the E6440 there are logs, but when I boot on the X201, no logs. I was so pleased with myself until there were no logs. > -- Or, enable some serial output device, either Intel AMT SOL [1] (if > supported for your X201) or plug in a PCMCIA serial card. You would need > (slightly) to re-configure Sculpt, see [2]. Add at the 7. step a 'LOG=core' > to the command, e.g. 'LOG=core make -C build/x86_64 run/sculpt KERNEL=nova > BOARD=pc'. The log output of Genode would now go over your serial device and > you may capture it. > > Hope it helps bit, > > Alex. > > [0] > https://genode.org/documentation/articles/sculpt-vc#Sculpt_as_a_hardware-probing_instrument > [1] https://genodians.org/chelmuth/2019-01-16-test-machine > [2] > https://genode.org/documentation/articles/sculpt-22-10#Building_the_boot_image > > > > > February 28, 2023 at 12:55 PM, "dogma--- via users" > > <[email protected]> wrote: > > > > > > > > February 28, 2023 at 8:16 AM, "Alexander Boettcher" > > > <[email protected]> wrote: > > > > > > > Hello, > > > > the X201 next to me on my desk is working fine with Sculpt 22.10. > > > > Several points which you can check: > > - Do you have an external monitor attached with a too high resolution > > (beyond 2K) ? > > - Do you using an docking station ? > > - Do you use coreboot instead of the default bios ? > > > > > > > > It’s good to know it should work. None of these apply to me. > > > > > > > Cheers, > > > > Alex. > > > > On 2/28/23 6:52 AM, dogma--- via users wrote: > > > > > > Image dd'ed to a flash drive, and I checked that vt-d, vt-x, and NX were > > as they should be. GRUB shows the splash image briefly, the screen goes > > blank black, something in the computer makes a moderately high-pitched > > sound for five seconds or so, and nothing more happens. > > _______________________________________________ > > Genode users mailing list > > [email protected] > > https://lists.genode.org/listinfo/users > > > > > > -- Alexander Boettcher > > Genode Labs > > > > https://www.genodians.org/ - https://www.genode.org/ > > > > _______________________________________________ > > Genode users mailing list > > [email protected] > > https://lists.genode.org/listinfo/users > > > > > > > > _______________________________________________ > > > Genode users mailing list > > > [email protected] > > > https://lists.genode.org/listinfo/users > > > > > > > > > _______________________________________________ > > Genode users mailing list > > [email protected] > > https://lists.genode.org/listinfo/users > > > > -- > Alexander Boettcher > Genode Labs > > https://www.genodians.org/ - https://www.genode.org/ > > _______________________________________________ > Genode users mailing list > [email protected] > https://lists.genode.org/listinfo/users > _______________________________________________ Genode users mailing list [email protected] https://lists.genode.org/listinfo/users
