Could you try : save("location","$((ff))") ? Do you get any error ?
What is your opensips version ? Regards, Bogdan-Andrei Iancu OpenSIPS Founder and Developer http://www.opensips-solutions.com On 05/22/2013 05:49 PM, Nathaniel L Keeling III wrote: > Hello Bogdan, > > I have validated the script and that i am passing a parameter. I also > changed the debug log statement that I displayed right before the > save() and I still get the same output. Here is the code that I use in > the script: > > > xlog("SAVING THE SUBSCRIBER INTO THE LOCATION TABLE, test with > extra debug ......................................."); > if (!save("location", "p1")) > { > xlog("L_ERR", "ERR:callerid:$ci|end|System error trying to > save Register's request location"); > sl_reply_error(); > } > > xlog("L_INFO", "INFO:callerid:$ci|end|The subscriber has > successfully registered with Akan Voice"); > exit; > > Is there a better way to validate? I am not sure of what else to check. > > Thanks > > Nathaniel L Keeling > > On 5/22/13 6:02 AM, Bogdan-Andrei Iancu wrote: >> Hi Nathaniel, >> >> Well, the logs shows that save() does not receive any flags as >> params...everything indicates that you do not have the params or you >> are using the wrong config file. >> >> Regards, >> Bogdan-Andrei Iancu >> OpenSIPS Founder and Developer >> http://www.opensips-solutions.com >> >> On 05/22/2013 08:22 AM, Nathaniel L Keeling III wrote: >>> Hello Bogdan, >>> >>> Here is the output from the opensips log. I have also attached a >>> snippet from the log file. >>> >>> May 21 23:39:15 OpenSips[14397]: [ID 257313 local1.debug] >>> DBG:registrar:save_aux: xXx - flags param is >>> May 21 23:39:15 OpenSips[14397]: [ID 154992 local1.debug] >>> DBG:registrar:save_aux: xXx - flags bitmask is <0> >>> >>> May 21 23:39:15 OpenSips[14397]: [ID 269964 local1.debug] >>> DBG:registrar:pack_ci: xXx - flags are 0 >>> >>> Thanks >>> >>> Nathaniel L Keeling >>> >>> On 5/20/13 11:56 AM, Bogdan-Andrei Iancu wrote: >>>> Hello Nathaniel, >>>> >>>> See the attached patch - it logs more from the part where the >>>> params are handled . >>>> >>>> Regards, >>>> Bogdan-Andrei Iancu >>>> OpenSIPS Founder and Developer >>>> http://www.opensips-solutions.com >>>> >>>> On 05/18/2013 09:33 AM, Nathaniel L Keeling III wrote: >>>>> Hello Bogdan, >>>>> >>>>> Here are snippets from my script. I only have one place where I >>>>> execute the save function. Just wondering, could it be truncating >>>>> a byte? >>>>> >>>>> modparam("usrloc", "nat_bflag", 10) >>>>> modparam("usrloc", "use_domain", 1) >>>>> modparam("usrloc", "db_mode", 3) >>>>> modparam("usrloc", "db_url", >>>>> "postgres://opensips:opensip...@ama.akan.net/opensips181t") >>>>> modparam("registrar", "tcp_persistent_flag", 7) >>>>> modparam("registrar", "received_avp", "$avp(received_nh)") >>>>> >>>>> >>>>> xlog("SAVING THE SUBSCRIBER INTO THE LOCATION TABLE >>>>> ...................................................."); >>>>> if (!save("location","p1")) >>>>> { >>>>> xlog("L_ERR", "ERR:callerid:$ci|end|System error trying to >>>>> save Register's request location"); >>>>> sl_reply_error(); >>>>> } >>>>> >>>>> xlog("L_NOTICE", "NOTICE:callerid:$ci|end|The subscriber has >>>>> successfully registered with Akan Voice"); >>>>> exit; >>>>> >>>>> Thanks >>>>> >>>>> Nathaniel >>>>> >>>>> On 5/17/13 6:07 AM, Bogdan-Andrei Iancu wrote: >>>>>> Hello Nathaniel, >>>>>> >>>>>> That is odd.....it's like you do not set the "p1" flag .... >>>>>> >>>>>> I tested and I with "p1" flag I get: >>>>>> May 17 14:05:03 [7944] DBG:registrar:pack_ci: xXx - flags are 10 >>>>>> >>>>>> Are you sure your script gets to the right save() ?? >>>>>> >>>>>> Regards, >>>>>> Bogdan-Andrei Iancu >>>>>> OpenSIPS Founder and Developer >>>>>> http://www.opensips-solutions.com >>>>>> >>>>>> On 05/17/2013 09:37 AM, Nathaniel L Keeling III wrote: >>>>>>> Hello Bogdan, >>>>>>> >>>>>>> I added the patch and here is what I found: "OpenSips[4378]: [ID >>>>>>> 269964 local1.debug] DBG:registrar:pack_ci: xXx - flags are 0". >>>>>>> I have also included the log file. >>>>>>> >>>>>>> Thanks >>>>>>> >>>>>>> Nathaniel Keeling >>>>>>> >>>>>>> On 5/16/13 3:47 AM, Bogdan-Andrei Iancu wrote: >>>>>>>> Hello Nathaniel, >>>>>>>> >>>>>>>> Attached is an extended patch - remove the old one and apply >>>>>>>> this one. Again look for any xXx logs . >>>>>>>> >>>>>>>> Regards, >>>>>>>> Bogdan-Andrei Iancu >>>>>>>> OpenSIPS Founder and Developer >>>>>>>> http://www.opensips-solutions.com >>>>>>>> >>>>>>>> On 05/14/2013 02:47 PM, Nathaniel L Keeling III wrote: >>>>>>>>> Hello Bogdan, >>>>>>>>> >>>>>>>>> here is the output from opensips's og file of the save() with >>>>>>>>> the patch and the code snippet from the opensips.cfg. I did >>>>>>>>> not see any ant logs with "xXx". Also,I have usrloc's db_mode >>>>>>>>> set to 3. >>>>>>>>> >>>>>>>>> xlog("SAVING THE SUBSCRIBER INTO THE LOCATION TABLE >>>>>>>>> ...................................................."); >>>>>>>>> if (!save("location","p1")) >>>>>>>>> { >>>>>>>>> xlog("L_ERR", "ERR:callerid:$ci|end|System error >>>>>>>>> trying to save Register's request location"); >>>>>>>>> sl_reply_error(); >>>>>>>>> } >>>>>>>>> xlog("L_NOTICE", "NOTICE:callerid:$ci|end|The subscriber >>>>>>>>> has successfully registered with Akan Voice"); >>>>>>>>> exit; >>>>>>> >>>>>>> >>>>>>> _______________________________________________ >>>>>>> Users mailing list >>>>>>> Users@lists.opensips.org >>>>>>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users >>>>>> >>>>>> >>>>>> _______________________________________________ >>>>>> Users mailing list >>>>>> Users@lists.opensips.org >>>>>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users >>>>> >>>>> >>>>> _______________________________________________ >>>>> Users mailing list >>>>> Users@lists.opensips.org >>>>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users >>> >
_______________________________________________ Users mailing list Users@lists.opensips.org http://lists.opensips.org/cgi-bin/mailman/listinfo/users