On Sun, May 29, 2022 at 7:50 PM Jonathan Baecker <jonba...@gmail.com> wrote:
>
> Hello everybody,
>
> we run a 3 node self hosted cluster with GlusterFS. I had a lot of problem
> upgrading ovirt from 4.4.10 to 4.5.0.2 and now we have cluster instability.
>
> First I will write down the problems I had with upgrading, so you get a
> bigger picture:
>
> engine update when fine
> But nodes I could not update because of wrong version of imgbase, so I did a
> manual update to 4.5.0.1 and later to 4.5.0.2. First time after updating it
> was still booting into 4.4.10, so I did a reinstall.
> Then after second reboot I ended up in the emergency mode. After a long
> searching I figure out that lvm.conf using use_devicesfile now but there it
> uses the wrong filters. So I comment out this and add the old filters back.
> This procedure I have done on all 3 nodes.
When use_devicesfile (default in 4.5) is enabled, lvm filter is not
used. During installation
the old lvm filter is removed.
Can you share more info on why it does not work for you?
- output of lsblk
- The old lvm filter used, and why it was needed
- output of vdsm-tool config-lvm-filter
If using lvm devices does not work for you, you can enable the lvm
filter in vdsm configuration
by adding a drop-in file:
$ cat /etc/vdsm/vdsm.conf.d/99-local.conf
[lvm]
config_method = filter
And run:
vdsm-tool config-lvm-filter
to configure the lvm filter in the best way for vdsm. If this does not create
the right filter we would like to know why, but in general you should use
lvm devices since it avoids the trouble of maintaining the filter and dealing
with upgrades and user edited lvm filter.
If you disable use_devicesfile, the next vdsm upgrade will enable it
back unless
you change the configuration.
Also even if you disable use_devicesfile in lvm.conf, vdsm still use
--devices instead
of filter when running lvm commands, and lvm commands run by vdsm ignore your
lvm filter since the --devices option overrides the system settings.
...
> I notice some unsync volume warning, but because I had this in the past to,
> after upgrading, I though after some time they will disappear. The next day
> there still where there, so I decided to put the nodes again in the
> maintenance mode and restart the glusterd service. After some time the sync
> warnings where gone.
Not clear what these warnings are, I guess Gluster warning?
> So now the actual problem:
>
> Since this time the cluster is unstable. I get different errors and warning,
> like:
>
> VM [name] is not responding
> out of nothing HA VM gets migrated
> VM migration can fail
> VM backup with snapshoting and export take very long
How do you backup the vms? do you sue a backup application? how is it
configured?
> VMs are getting very slow some times
> Storage domain vmstore experienced a high latency of 9.14251
> ovs|00001|db_ctl_base|ERR|no key "dpdk-init" in Open_vSwitch record "."
> column other_config
> 489279 [1064359]: s8 renewal error -202 delta_length 10 last_success 489249
> 444853 [2243175]: s27 delta_renew read timeout 10 sec offset 0
> /rhev/data-center/mnt/glusterSD/onode1.example.org:_vmstore/3cf83851-1cc8-4f97-8960-08a60b9e25db/dom_md/ids
> 471099 [2243175]: s27 delta_renew read timeout 10 sec offset 0
> /rhev/data-center/mnt/glusterSD/onode1.example.org:_vmstore/3cf83851-1cc8-4f97-8960-08a60b9e25db/dom_md/ids
> many of: 424035 [2243175]: s27 delta_renew long write time XX sec
All these issues tell use that your storage is not working correctly.
sanlock.log is full of renewal errors form May:
$ grep 2022-05- sanlock.log | wc -l
4844
$ grep 2022-05- sanlock.log | grep 'renewal error' | wc -l
631
But there is lot of trouble from earlier months:
$ grep 2022-04- sanlock.log | wc -l
844
$ grep 2022-04- sanlock.log | grep 'renewal error' | wc -l
29
$ grep 2022-03- sanlock.log | wc -l
1609
$ grep 2022-03- sanlock.log | grep 'renewal error' | wc -l
483
$ grep 2022-02- sanlock.log | wc -l
826
$ grep 2022-02- sanlock.log | grep 'renewal error' | wc -l
242
Here sanlock log looks healthy:
$ grep 2022-01- sanlock.log | wc -l
3
$ grep 2022-01- sanlock.log | grep 'renewal error' | wc -l
0
$ grep 2021-12- sanlock.log | wc -l
48
$ grep 2021-12- sanlock.log | grep 'renewal error' | wc -l
0
vdsm log shows that 2 domains are not accessible:
$ grep ERROR vdsm.log
2022-05-29 15:07:19,048+0200 ERROR (check/loop) [storage.monitor]
Error checking path
/rhev/data-center/mnt/glusterSD/onode1.example.org:_data/de5f4123-0fac-4238-abcf-a329c142bd47/dom_md/metadata
(monitor:511)
2022-05-29 16:33:59,049+0200 ERROR (check/loop) [storage.monitor]
Error checking path
/rhev/data-center/mnt/glusterSD/onode1.example.org:_data/de5f4123-0fac-4238-abcf-a329c142bd47/dom_md/metadata
(monitor:511)
2022-05-29 16:34:39,049+0200 ERROR (check/loop) [storage.monitor]
Error checking path
/rhev/data-center/mnt/glusterSD/onode1.example.org:_data/de5f4123-0fac-4238-abcf-a329c142bd47/dom_md/metadata
(monitor:511)
2022-05-29 17:21:39,050+0200 ERROR (check/loop) [storage.monitor]
Error checking path
/rhev/data-center/mnt/glusterSD/onode1.example.org:_data/de5f4123-0fac-4238-abcf-a329c142bd47/dom_md/metadata
(monitor:511)
2022-05-29 17:55:59,712+0200 ERROR (check/loop) [storage.monitor]
Error checking path
/rhev/data-center/mnt/glusterSD/onode1.example.org:_vmstore/3cf83851-1cc8-4f97-8960-08a60b9e25db/dom_md/metadata
(monitor:511)
2022-05-29 17:56:19,711+0200 ERROR (check/loop) [storage.monitor]
Error checking path
/rhev/data-center/mnt/glusterSD/onode1.example.org:_vmstore/3cf83851-1cc8-4f97-8960-08a60b9e25db/dom_md/metadata
(monitor:511)
2022-05-29 17:56:39,050+0200 ERROR (check/loop) [storage.monitor]
Error checking path
/rhev/data-center/mnt/glusterSD/onode1.example.org:_data/de5f4123-0fac-4238-abcf-a329c142bd47/dom_md/metadata
(monitor:511)
2022-05-29 17:56:39,711+0200 ERROR (check/loop) [storage.monitor]
Error checking path
/rhev/data-center/mnt/glusterSD/onode1.example.org:_vmstore/3cf83851-1cc8-4f97-8960-08a60b9e25db/dom_md/metadata
(monitor:511)
You need to find what is the issue with your Gluster storage.
I hope that Ritesh can help debug the issue with Gluster.
Nir
_______________________________________________
Users mailing list -- users@ovirt.org
To unsubscribe send an email to users-le...@ovirt.org
Privacy Statement: https://www.ovirt.org/privacy-policy.html
oVirt Code of Conduct:
https://www.ovirt.org/community/about/community-guidelines/
List Archives:
https://lists.ovirt.org/archives/list/users@ovirt.org/message/KZ2QNULKMWXAPNHOGGIA7GBXLLILPUEX/
