Dear Derek, I tried the link that you gave but no luck.1) I disabled the use of timestamp and, dissecting the packets with wireshark, I cross-checked that the use_timestamp bit is 0. 2) I added the set_rx_streamer and issue_cmd to my flograph but nothing happens. I am not sure if both commands work properly, but I guess they do.
Do you have additional hints on that? Thank you. Dr. Pol Henarejos Researcher Array and Multi-Sensor Processing Department, Communication Systems Division pol.henare...@cttc.cat Centre Tecnològic de Telecomunicacions de Catalunya (CTTC) Av. Carl Friedrich Gauss, 7 08860 Castelldefels, Barcelona (Spain) Tel: +34 93 645 29 00 Ext: 2177 www.cttc.cat El 22/6/2018 a les 14:21, Pol Henarejos via USRP-users ha escrit:
Thank you, Derek. I will take a look. I hope that some progress will be achieved in a near future. Best regards. Dr. Pol Henarejos ResearcherArray and Multi-Sensor Processing Department, Communication Systems Divisionpol.henare...@cttc.cat Centre Tecnològic de Telecomunicacions de Catalunya (CTTC) Av. Carl Friedrich Gauss, 7 08860 Castelldefels, Barcelona (Spain) Tel: +34 93 645 29 00 Ext: 2177 www.cttc.cat El 22/6/2018 a les 13:13, Derek Kozel ha escrit:Hello Dr Henarejos,Currently an RFNoC only flowgraph is not fully supported. What is missing is the issuing of the commands to start streaming and a mechanism to handle timestamps. Some modifications are needed to make these work. Nick Foster has done a write up on a few different ways of handling the necessary modifications.https://corvid.io/2017/04/22/stupid-rfnoc-tricks-loopback/ Regards, DerekOn Fri, Jun 22, 2018 at 10:10 AM, Pol Henarejos via USRP-users <usrp-users@lists.ettus.com <mailto:usrp-users@lists.ettus.com>> wrote:Dear all, I am playing with RFNoC on a USRP X300. I built a custom RFNoC FPGA image with the blocks that I need successfully and everything goes smooth. However, if I want to use a flowgraph with only RFNoC blocks (RFNoC Radio RX --> DmaFIFO --> RFNoC Radio TX), it does not work. The USRP does nothing (no blinking leds, no error messages, nothing). If I replace the DmaFIFO block with a Copy block, then it works but, as expected, this is not efficient since all the samples go to the host and go back to the USRP. I would want to perform a relay by using only RFNoC blocks. My impression is that a command to the USRP might be needed (a streaming command or so), but I have no idea what is wrong. I attach the flowgraph. (only RFNoC blocks does not work) (flowing samples to host and going back to USRP does work but it is extremely inefficient) Thank you. -- Dr. Pol Henarejos ResearcherArray and Multi-Sensor Processing Department, Communication Systems Divisionpol.henare...@cttc.cat <mailto:pol.henare...@cttc.cat> Centre Tecnològic de Telecomunicacions de Catalunya (CTTC) Av. Carl Friedrich Gauss, 7 08860 Castelldefels, Barcelona (Spain) Tel: +34 93 645 29 00 Ext: 2177 www.cttc.cat <http://www.cttc.cat> _______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com <mailto:USRP-users@lists.ettus.com> http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com <http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com>_______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
smime.p7s
Description: Signatura criptogràfica S/MIME
_______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
