OK, that's an important data point. Now I just need to be able to
reproduce the failure. :|
On 3/22/22 2:56 PM, Richard Ems wrote:
Hi DRC,
Just tested and it does not fail just using the local X server. See
attached output.
Thanks,
Richard
On Tue, 22 Mar 2022 at 15:19, 'DRC' via VirtualGL User
Discussion/Support <[email protected]> wrote:
On 3/22/22 12:26 PM, Richard Ems wrote:
Is there any way that you could try running the Tecplot batch
job on the 3D X server without VirtualGL? If it fails in the
same way, then it isn't our bug.
Do you mean on a local attached display? That won't be easy,
since this graphics workstation is part of a cluster located far
away from me or the user getting this bug.
I have just contacted Tecplot Support and I'm waiting for their
response and a trial license to test myself using my own environment.
The 3D X server is on the VirtualGL server, which should be the
same machine on which Tecplot 360 is installed. Unless the
machine has been configured otherwise, the 3D X server should be
listening on Display :0.0, so try:
xauth merge /etc/opt/VirtualGL/vgl_xauth_key
LD_PRELOAD= DISPLAY=:0.0 ./Tec360_FlowViz_batch.sh
I remember to have to preload libvglfaker.so for starccm+ to work
properly. Anything similar perhaps needed here for tec360? Just
some more guessing. Worth a try?
Preloading libvglfaker.so is literally what vglrun does. I am not
trying to make Tecplot 360 work properly. I am trying to make it
fail.
Thanks,
Richard
On Tue, 22 Mar 2022 at 13:58, 'DRC' via VirtualGL User
Discussion/Support <[email protected]> wrote:
I tried it with '$useVGL = 1' as well and was still unable to
reproduce the issue. (Note that, from the point of view of
the application, setting '$useVGL = 1' in turbovncserver.conf
or starting the TurboVNC session with '-vgl' is the same as
launching the application with 'vglrun +wm'.)
I also tried with both CentOS 7.9 and CentOS Stream 8. My
CentOS 7.9 machine has a Quadro K5000 with driver v470.xx. My
CentOS 8 machine has a Quadro P620 with driver v510.xx.
Is there any way that you could try running the Tecplot batch
job on the 3D X server without VirtualGL? If it fails in the
same way, then it isn't our bug.
DRC
On 3/22/22 11:01 AM, Richard Ems wrote:
Hi DRC,
sorry, I forgot to comment out that module command, that
would only add the Tecplot installation PATH to the bash
PATH variable,
But as I see from your output the tec360 command in
Tec360_FlowViz_batch.sh started fine, so it is already in
your PATH, so all good.
Did that tec360 run end without errors?
Is your setup also using $useVGL = 1; in
/etc/turbovncserver.conf ?
Just guessing possible differences.
Thanks for testing,
Richard
On Tue, 22 Mar 2022 at 11:37, 'DRC' via VirtualGL User
Discussion/Support <[email protected]> wrote:
Please clarify how this is supposed to work. 'module
load' is not a valid Bash command.
==========
> vglrun ./Tec360_FlowViz_batch.sh
./Tec360_FlowViz_batch.sh: line 3: module: command not found
Tecplot 2021.2.1.9698 - 21:07:35 Feb 3 2022
[linux64-centos6.10]
Color maps directory :
/usr/local/tecplot/360ex_2021r2/colormaps
Configuration File :
/usr/local/tecplot/360ex_2021r2/tecplot.cfg
Process Temp Dir : /usr/tmp/tecplot_drc/tpaqmYUE0
Tecplot internal font file:
/usr/local/tecplot/360ex_2021r2/tecplot.fnt
LaTeX Configuration File:
/usr/local/tecplot/360ex_2021r2/tecplot_latex.mcr
Your license expires at the end of 26-Mar-2022.
Update your license, or contact [email protected] for
help.
Tecplot executable :
/usr/local/tecplot/360ex_2021r2/bin/tec360-bin
Tecplot Home Directory : /usr/local/tecplot/360ex_2021r2
QuickMacro File :
/usr/local/tecplot/360ex_2021r2/tecplot.mcr
Addon Startup File :
/usr/local/tecplot/360ex_2021r2/tecplot.add
AddOn Loaded : Tecplot Subzone Data Loader
AddOn Loaded : SZL Remote Loader
AddOn Loaded : CFD Analyzer
AddOn Loaded : CGNS Loader
AddOn Loaded : DEM Loader
AddOn Loaded : DXF Loader
AddOn Loaded : EnSight Loader
AddOn Loaded : FLOW-3D Loader
AddOn Loaded : Fluent Common Fluid Files Loader
AddOn Loaded : Fluent Data Loader
AddOn Loaded : General Text Loader
AddOn Loaded : HDF Loader
AddOn Loaded : PLOT3D Loader
AddOn Loaded : PLY Polygon File Loader
AddOn Loaded : Text Spreadsheet Loader
AddOn Loaded : Kiva Loader
AddOn Loaded : Finite Element Analysis Loader
AddOn Loaded : Write Data as Text
AddOn Loaded : VTK Data Loader
AddOn Loaded : FVCOM netCDF Loader
AddOn Loaded : CONVERGE HDF5 File Loader
AddOn Loaded : CONVERGE Output File Loader
AddOn Loaded : Exodus File Loader
AddOn Loaded : Telemac Data Loader
AddOn Loaded : HDF5 Loader
AddOn Loaded : Akima Spline
AddOn Loaded : General Curve Fit
AddOn Loaded : Stineman Interpolation
AddOn Loaded : extendmcr
AddOn Loaded : Advanced Quick Edit Tool
AddOn Loaded : Multi Frame Manager
AddOn Loaded : Create Multiple Frames
AddOn Loaded : Tensor Eigensystem
AddOn Loaded : Key Frame Animation
AddOn Loaded : Aux Data Editor
AddOn Loaded : Time Series Plot
AddOn Loaded : Extract Blanked Zone
AddOn Loaded : Extract Precise Line
AddOn Loaded : Extract Over Time
AddOn Loaded : Link Solution Time
AddOn Loaded : Extend Time MCR
AddOn Loaded : Strand Editor
AddOn Loaded : Measure Distance
==========
DRC
On 3/21/22 4:25 PM, Richard Ems wrote:
Hi DRC,
find attached an example using Tecplot's Onera example
model.
Thanks,
Richard
On Mon, 21 Mar 2022 at 15:28, 'DRC' via VirtualGL User
Discussion/Support <[email protected]>
wrote:
I have installed Tecplot 360 with an evaluation
license. Please specify the exact steps needed to
reproduce the issue using one of the Tecplot examples.
DRC
On 3/21/22 7:54 AM, Richard Ems wrote:
Hi DRC, hi all,
First, thanks DRC for this great software!
We are having some issue with Tecplot / tec360 and
VirtualGL:
Some system specs:
Rocky Linux 8.5
VirtualGL-3.0-20211119.x86_64
turbovnc-2.2.90-20211222.x86_64
NVIDIA Corporation GM204GL [Tesla M60]
Tecplot 360 EX 2021 R2, Version 2021.2.1.9698 (Feb
3 2022)
VirtualGL is configured with both GLX + EGL back ends.
$useVGL = 1; in /etc/turbovncserver.conf
While trying to run tec360 on batch mode we get
the attached error output.
Here the last 10 lines:
/net/c1m1/data_1/opt/Tecplot360/360ex_2021r2/bin/../bin/libtpsdkbase.so(TecEngStartup+0x24)
[0x7f93fdad0394]
/net/c1m1/data_1/opt/Tecplot360/360ex_2021r2/bin/../bin/libtpsdkintegrationmanager.so(_ZN7tecplot3sdk11integration15ManagerAbstract5startEv+0x19)
[0x7f93fe92b1b9]
/net/c1m1/data_1/opt/Tecplot360/360ex_2021r2/bin/tec360-bin()
[0x487ef5]
/lib64/libc.so.6(__libc_start_main+0xf3)
[0x7f93fb4c0493]
/net/c1m1/data_1/opt/Tecplot360/360ex_2021r2/bin/tec360-bin()
[0x489d09]
Tecplot received shutdown signal.
Signal #11
Please send the output above to Tecplot support:
[email protected]
/net/c1m1/data_1/opt/Tecplot360/360ex_2021r2/bin/tec360:
line 349: 276303 Aborted (core dumped) "$0-bin" "$@"
Any ideas what is going wrong?
When running with tec360 option "--osmesa" all
runs fine, but it takes 17 min to run.
--osmesa
Bypass the OpenGL library and use the LLVM
OSMesa library for off-screen
image rendering. This option does not require
an X server connection.
Best regards,
Richard
--
You received this message because you are subscribed to the Google Groups "VirtualGL
User Discussion/Support" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/virtualgl-users/14b5014b-6277-0440-e9c5-11f7e517419a%40virtualgl.org.
