Thanks for reply. I change my configuration vpls based on topolgy.VPLS
configuration:MPLS L2VPN VPLS######## ######## ######## ########VPP1-VM1
########set int state eth1 upset int state eth0 upset int ip address eth1
2.1.1.1/24
mpls tabel add 0 set interface mpls eth1 enablempls tunnel l2-only via
2.1.1.2 eth1 out-labels 34 set int state mpls-tunnel0 upset interface l2
bridge mpls-tunnel0 1 set interface l2 bridge eth0 1mpls local-label add eos
1023 via l2-input-on mpls-tunnel0######## ######## ######## ########
####VPP2-VM######set int state eth1 upset int state eth0 upset int ip address
eth1 2.1.1.2/24
mpls table add 0set interface mpls eth1 enable mpls tunnel l2-only via
2.1.1.1 eth1 out-labels 1024set interface l2 bridge mpls-tunnel0 1 set
interface l2 bridge eth0 1mpls local-label add eos 33 via l2-input-on
mpls-tunnel0#####################################################################
dont ping between host1 and host2.now,Is my configuration vpls correct based on
topology? How do I trace packet on specific node ?
best regards.
On Monday, April 30, 2018, 6:41:18 PM GMT+4:30, Neale Ranns
<nra...@cisco.com> wrote:
Looks OK to me. Packet trace maybe?
Just a note, you don’t need two out-labels on your tunnel (and so you don’t
need to neos entry on RX)
/neale
From: <vpp-dev@lists.fd.io> on behalf of "omid via Lists.Fd.Io"
<zeinalpouromid=yahoo....@lists.fd.io>
Reply-To: "zeinalpouro...@yahoo.com" <zeinalpouro...@yahoo.com>
Date: Monday, 30 April 2018 at 14:45
To: "vpp-dev@lists.fd.io" <vpp-dev@lists.fd.io>
Cc: "vpp-dev@lists.fd.io" <vpp-dev@lists.fd.io>
Subject: [vpp-dev] #vpp vpls configuration
Hi, my configurtion vpls is based on toplogy.
VPLS configuration: MPLS L2VPN VPLS ######## ######## ######## ########
VPP1-VM1
######## set int state eth1 up set int state eth0 up set int ip address eth1
2.1.1.1/24
mpls tabel add 0 set interface mpls eth1 enable mpls tunnel l2-only via
2.1.1.2 eth1 out-labels 34 out-labels 33 set int state mpls-tunnel0 up set
interface l2 bridge mpls-tunnel0 1 set interface l2 bridge eth0 1 mpls
local-label add eos 1023 via l2-input-on mpls-tunnel0 mpls local-label add
non-eos 1024 via mpls-lookup-in-table 0 ######## ######## ######## ########
####VPP2-VM###### set int state eth1 up set int state eth0 up set int ip
address eth1 2.1.1.2/24
mpls table add 0 set interface mpls eth1 enable mpls tunnel l2-only via
2.1.1.1 eth1 out-labels 1024 out-labels 1023 set int state mpls-tunnel0 up set
interface l2 bridge mpls-tunnel0 1 set interface l2 bridge eth0 1 mpls
local-label add eos 33 via l2-input-on mpls-tunnel0 mpls local-label add
non-eos 34 via mpls-lookup-in-table 0
#####################################################################
dont ping between host1 and host2.Is my configuration vpls correct based on
topology?
