Which node do I trace? then i show trace .

    On Tuesday, May 1, 2018, 11:49:15 AM GMT+4:30, Neale Ranns 
<[email protected]> wrote:
 
 
https://wiki.fd.io/view/VPP/Command-line_Interface_(CLI)_Guide#packet_tracer
 
  
 
/neale
 
  
 

From: Omid Zeinalpour <[email protected]>
Date: Tuesday, 1 May 2018 at 08:49
To: "[email protected]" <[email protected]>, "Neale Ranns (nranns)" 
<[email protected]>
Subject: Re: [vpp-dev] #vpp vpls configuration
 
  
 
Thanks for reply. I change my configuration vpls based on topolgy.
 VPLS configuration: MPLS L2VPN VPLS ######## ######## ######## ######## 
VPP1-VM1  
######## set int state eth1 up set int state eth0 up set int ip address eth1 
2.1.1.1/24  
mpls tabel add 0  set interface mpls  eth1   enable mpls tunnel l2-only via 
2.1.1.2 eth1 out-labels 34   set int state mpls-tunnel0 up set interface l2 
bridge  mpls-tunnel0 1  set interface l2 bridge eth0  1 mpls local-label add 
eos 1023 via l2-input-on mpls-tunnel0 ######## ######## ######## ########  
####VPP2-VM###### set int state eth1 up set int state eth0 up set int ip 
address eth1 2.1.1.2/24 
mpls table add 0 set interface mpls  eth1   enable    mpls tunnel l2-only via 
2.1.1.1 eth1 out-labels 1024 set interface l2 bridge mpls-tunnel0 1  set 
interface l2 bridge eth0  1 mpls local-label add eos 33 via l2-input-on 
mpls-tunnel0 
#####################################################################
dont ping between host1 and host2.now,Is my configuration vpls correct based on 
topology?  How do I trace packet on specific node ? best regards. 
  
 
On Monday, April 30, 2018, 6:41:18 PM GMT+4:30, Neale Ranns <[email protected]> 
wrote:
 
  
 
  
 
Looks OK to me. Packet trace maybe?
 
 
 
Just a note, you don’t need two out-labels on your tunnel (and so you don’t 
need to neos entry on RX)
 
 
 
/neale
 
 
 

From:<[email protected]> on behalf of "omid via Lists.Fd.Io" 
<[email protected]>
Reply-To: "[email protected]" <[email protected]>
Date: Monday, 30 April 2018 at 14:45
To: "[email protected]" <[email protected]>
Cc: "[email protected]" <[email protected]>
Subject: [vpp-dev] #vpp vpls configuration
 
 
 

 
 
 Hi, my configurtion vpls is based on toplogy.
VPLS configuration: MPLS L2VPN VPLS ######## ######## ######## ######## 
VPP1-VM1  
######## set int state eth1 up set int state eth0 up set int ip address eth1 
2.1.1.1/24  
mpls tabel add 0  set interface mpls  eth1   enable mpls tunnel l2-only via 
2.1.1.2 eth1 out-labels 34  out-labels 33 set int state mpls-tunnel0 up set 
interface l2 bridge  mpls-tunnel0 1  set interface l2 bridge eth0  1 mpls 
local-label add eos 1023 via l2-input-on mpls-tunnel0 mpls local-label add 
non-eos 1024 via mpls-lookup-in-table 0    ######## ######## ######## ########  
####VPP2-VM###### set int state eth1 up set int state eth0 up set int ip 
address eth1 2.1.1.2/24 
mpls table add 0 set interface mpls  eth1   enable    mpls tunnel l2-only via 
2.1.1.1 eth1 out-labels 1024 out-labels 1023 set int state mpls-tunnel0 up set 
interface l2 bridge mpls-tunnel0 1  set interface l2 bridge eth0  1 mpls 
local-label add eos 33 via l2-input-on mpls-tunnel0 mpls local-label add 
non-eos 34 via mpls-lookup-in-table 0
#####################################################################
dont ping between host1 and host2.Is my configuration vpls correct based on 
topology? 




Reply via email to