Thanks...

It looks like your configuration specifies station #2 as an exception which 
might mean that Weewx can see the #1 Station by default.  

I will give it a try.

On Friday, August 30, 2019 at 9:27:40 AM UTC-7, paul bennett wrote:
>
> I have exactly that setup - a VP2 with a separate wireless staion on the 
> roof for the anemometer.  The VP2 base station is configured to receive 
> from Station 2.  Here's the [Vantage] section from my weewx.conf:
>
>
> ##############################################################################
>
> [Vantage]
>     # This section is for the Davis Vantage series of weather stations.
>
>     # Connection type: serial or ethernet
>     #  serial (the classic VantagePro)
>     #  ethernet (the WeatherLinkIP or Serial-Ethernet bridge)
>     type = serial
>
>     # If the connection type is serial, a port must be specified:
>     #   Debian, Ubuntu, Redhat, Fedora, and SuSE:
>     #     /dev/ttyUSB0 is a common USB port name
>     #     /dev/ttyS0   is a common serial port name
>     #   BSD:
>     #     /dev/cuaU0   is a common serial port name
>     port = /dev/ttyUSB0
>
>     # If the connection type is ethernet, an IP Address/hostname is 
> required:
> #-#     host = 1.2.3.4
>
>     ######################################################
>     # The rest of this section rarely needs any attention.
>     # You can safely leave it "as is."
>     ######################################################
>
>     # Serial baud rate (usually 19200)
>     baudrate = 19200
>
>     # TCP port (when using the WeatherLinkIP)
>     tcp_port = 22222
>
>     # TCP send delay (when using the WeatherLinkIP):
>     tcp_send_delay = 0.5
>
>     # The id of your ISS station (usually 1). If you use a wind meter 
> connected
>     # to a anemometer transmitter kit, use its id
>     iss_id = 2
>
>     # How long to wait for a response from the station before giving up (in
>     # seconds; must be greater than 2)
>     timeout = 4
>
>     # How long to wait before trying again (in seconds)
>     wait_before_retry = 1.2
>
>     # How many times to try before giving up:
>     max_tries = 4
>
>     # Vantage model Type: 1 = Vantage Pro; 2 = Vantage Pro2
>     model_type = 2
>
>     # The driver to use:
>     driver = weewx.drivers.vantage
>
>
> ##############################################################################
>
> Hope that helps...
>
>
> On Friday, August 30, 2019 at 8:49:04 AM UTC-6, Bob Borzelleri wrote:
>>
>> I am switching to a Raspberry Pi 4 with Weewx from a PC running 
>> Weatherlink for the past 15 years.  Previously, I ran the anemometer hard 
>> wired into the ISS which would work fine, I assume, with Weewx seeing all 
>> sensor inputs (rain, temp/humidity/ solar radiation and wind) from ISS = 1.
>>
>> Now that I am 15 years older than when I started this weather stuff, I no 
>> longer wish to hang off the roof in order to maintain the ISS so I am 
>> relocating it to a spot in the yard that does not require a crane in order 
>> to get to.  I have switched the anemometer from hard wire in the ISS to 
>> plugging into a Davis wireless sensor transmitter.
>>
>> The Weewx configuration file seems to be happy   seeing the ISS as 
>> Station 1 ( ISS = 1), but adding Station 2 on the next line (Anemometer = 
>> 2)  doesn't seem to be the hot setup.
>>
>> If anyone has two Davis Vantage Pro stations feeding into Weewx, I'd 
>> appreciate seeing how they included the 2nd one in the configuration file.
>>
>> BTW, the Davis Console is set up to see the 2nd station and reports its 
>> activity.  I also have an Envoy that I set up through Weathlink to see the 
>> 2nd station (menu driven Q & A) and have it plugged into the RPi.  I 
>> reports all data from the ISS, but not the anemometer and lists N/A 
>> alongside the Current Conditions for wind.
>>
>> Now that I have just called up the page, I see that the Barometer shows 
>> the current reading but also shows (N/A) after the reading.
>>
>> Any help would be greatly appreciated.
>>
>> ...Bob
>>
>>  
>>
>

-- 
You received this message because you are subscribed to the Google Groups 
"weewx-user" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to weewx-user+unsubscr...@googlegroups.com.
To view this discussion on the web visit 
https://groups.google.com/d/msgid/weewx-user/27164987-fd7b-4905-948d-9328a96953ff%40googlegroups.com.

Reply via email to