Looking at the Peet Bros protocol
<https://www.peetbros.com/shop/custom.aspx?recid=29>, they say the baud
rate is 2,400, so you got that right. Make sure it's 8 data bits, 1 stop
bit, no parity.
Something I'm not understanding: you are using port /dev/ttyS0, which is a
typical serial port. However, the Ultimeter is at a remote location. How
does it connect to the port? Perhaps the problem is somewhere in that link?
On Fri, May 28, 2021 at 7:51 AM valken...@gmail.com <valkenier...@gmail.com>
wrote:
> Thnx again. I think it must be the right port since there is only 1 serial
> device connected. If you say the output of ttyS0 is not normal ultimeter
> output, i assume we found the cause of the disfunctioning. I used baud
> rate 2400 for the screen command. The output is not readable indeed, but it
> is a flow of data. Maybe the unit is not in logger mode since teh power
> outage. Unfornately the station is at a remote location. I'll see if i can
> get someone up there to check the Ultimeter and the setup. I'll let you
> know.
>
> Op vrijdag 28 mei 2021 om 16:15:07 UTC+2 schreef tke...@gmail.com:
>
>> That does not look like the Ultimeter protocol, which typically has
>> double exclamation points ('!!') every 42, 46, or 50 bytes. Are you sure
>> you have the baud rate correct? Have the right port?
>>
>> On Fri, May 28, 2021 at 6:31 AM valken...@gmail.com <valken...@gmail.com>
>> wrote:
>>
>>> screen /dev/ttyS0 2400 shows me:
>>>
>>> &CR&004900D9008400EB026E026E0000----000000000000026A------------0000056901B7021700000000000001B7021701CD030600000000000001CD03062BA70000004300DA0000000000002BA70000022C0000000000000000022C000003F2000000000000000003F2000003F2000000000000000003F20000013900200000000000000139002002E503ED004300DA00000000000002E503ED13D3000000000000000013D30000026A0559000000000000026A05590000000000000000000000000000000000000000000000000000000000000000000000010000DC00DC00002D
>>> &CR&004500D2008400EB026E026E0000----0000000000000269------------00000569
>>> etcetera
>>>
>>> Op vrijdag 28 mei 2021 om 15:08:56 UTC+2 schreef valken...@gmail.com:
>>>
>>>> Exactly nothing happens:
>>>>
>>>> ****@kwsweerstation:/etc/weewx# weewxd
>>>>
>>>> And then the screen stays completely blank......
>>>>
>>>> Op vrijdag 28 mei 2021 om 15:00:08 UTC+2 schreef tke...@gmail.com:
>>>>
>>>>> What happens when you run weewxd directly from the console?
>>>>>
>>>>> On Fri, May 28, 2021 at 5:54 AM valken...@gmail.com <
>>>>> valken...@gmail.com> wrote:
>>>>>
>>>>>> Dear Tom,
>>>>>>
>>>>>> Thank you for your answer. You are right. This is a very short
>>>>>> interval. I let it run much longer earlier, and nothing else showed up in
>>>>>> the logs. Indeed, I quit weewx by systemctl stop weewx. Then I noticed
>>>>>> this
>>>>>> error, an I assumed it might yield an answer. To get a clean piece of
>>>>>> logs, did a start and stop in a short time. (But that's not helpful I
>>>>>> understand now.) I did run weewxd (after stopping weewx), but it show no
>>>>>> output whatsoever. Just nothing. Blank. So now data received from ttyS0?
>>>>>> When i start weewx by systemctl. The log gives me the same output.
>>>>>> The last log entry is:
>>>>>> kwsweerstation weewx[12255] DEBUG weewx.manager: Daily summary
>>>>>> version is 4.0
>>>>>>
>>>>>> After that no further entries appear. The rest of the log above this
>>>>>> entry is exactly similar to the log shown in the openig post. I think
>>>>>> there
>>>>>> is some issue with the serial connection, although screen gives me some
>>>>>> encoded output.
>>>>>> Op vrijdag 28 mei 2021 om 14:30:26 UTC+2 schreef tke...@gmail.com:
>>>>>>
>>>>>>> In this log sample, I assume you stopped weewx by doing something
>>>>>>> like "systemctl stop weewx". If so, the "error in the log" is just the
>>>>>>> normal shutdown chatter and doesn't mean anything.
>>>>>>>
>>>>>>> In this sample, there is only 3 seconds between when weewx had
>>>>>>> finished initializing, and when the shutdown sequence started. That's
>>>>>>> not
>>>>>>> enough time to judge whether weewx was doing anything.
>>>>>>>
>>>>>>> Suggestions:
>>>>>>> 1. Let it run longer. At least an archive period.
>>>>>>> 2. Alternatively, run weewxd directly from the console
>>>>>>> <http://www.weewx.com/docs/usersguide.htm#Running_directly> for a
>>>>>>> while. It will print out LOOP packets as they arrive, allowing you to
>>>>>>> check
>>>>>>> whether weewx is properly receiving data.
>>>>>>>
>>>>>>> -tk
>>>>>>>
>>>>>>> On Fri, May 28, 2021 at 5:03 AM valken...@gmail.com <
>>>>>>> valken...@gmail.com> wrote:
>>>>>>>
>>>>>>>> Hi,
>>>>>>>> Iḿ having troubles with a weewx inatance running on ubuntu 20.
>>>>>>>> After an unforseen power outage, the system came back up, but weewx
>>>>>>>> stopped
>>>>>>>> processing data. The system is connected to an ulitmeter 2100 via
>>>>>>>> ttyS0.
>>>>>>>> With screen I do see data on that port. However weewx starts, and does
>>>>>>>> nothing. No errors in the log, no activity at actually after starting
>>>>>>>> weewx. If I manually stop weewx, it results in an error in the log,
>>>>>>>> before
>>>>>>>> stopping. I reinstalled weewx, emptied the database but no effect. I
>>>>>>>> just
>>>>>>>> doesn´t process data. Debug level=1. Maybe someone can help me out?
>>>>>>>>
>>>>>>>> Log entries:
>>>>>>>>
>>>>>>>> May 28 14:00:18 kwsweerstation systemd[1]: Starting LSB: weewx
>>>>>>>> weather system...
>>>>>>>> May 28 14:00:18 kwsweerstation weewx[11973]: * Starting weewx
>>>>>>>> weather system weewx
>>>>>>>> May 28 14:00:18 kwsweerstation weewx[11991] INFO __main__:
>>>>>>>> Initializing weewx version 4.5.1
>>>>>>>> May 28 14:00:18 kwsweerstation weewx[11991] INFO __main__: Using
>>>>>>>> Python 3.8.5 (default, Jan 27 2021, 15:41:15) #012[GCC 9.3.0]
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11991] INFO __main__: Platform
>>>>>>>> Linux-5.4.0-73-generic-x86_64-with-glibc2.29
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11991] INFO __main__: Locale
>>>>>>>> is 'nl_NL.UTF-8'
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11991] INFO __main__: PID file
>>>>>>>> is /var/run/weewx.pid
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO __main__: Using
>>>>>>>> configuration file /etc/weewx/weewx.conf
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO __main__: Debug is
>>>>>>>> 1
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> Initializing engine
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO weewx.engine:
>>>>>>>> Loading station type Ultimeter (weewx.drivers.ultimeter)
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO
>>>>>>>> weewx.drivers.ultimeter: Driver version is 0.41
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO
>>>>>>>> weewx.drivers.ultimeter: Using serial port /dev/ttyS0
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG
>>>>>>>> weewx.drivers.ultimeter: Open serial port /dev/ttyS0
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.engine.StdTimeSynch
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.engine.StdTimeSynch
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.engine.StdConvert
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO weewx.engine:
>>>>>>>> StdConvert target unit is 0x1
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.engine.StdConvert
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.engine.StdCalibrate
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.engine.StdCalibrate
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.engine.StdQC
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.engine.StdQC
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.wxservices.StdWXCalculate
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11973]: ...done.
>>>>>>>> May 28 14:00:19 kwsweerstation systemd[1]: Started LSB: weewx
>>>>>>>> weather system.
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.manager:
>>>>>>>> Daily summary version is 4.0
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.wxservices.StdWXCalculate
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service user.cmon.ComputerMonitor
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon: service
>>>>>>>> version is 0.20
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.manager:
>>>>>>>> Daily summary version is 4.0
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> sysinfo: Linux kwsweerstation 5.4.0-73-generic #82-Ubuntu SMP Wed Apr
>>>>>>>> 14
>>>>>>>> 17:39:42 UTC 2021 x86_64
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: processor: 3
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: vendor_id: GenuineIntel
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: cpu family: 6
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: model: 28
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: model name: Intel(R) Atom(TM) CPU 330 @ 1.60GHz
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: stepping: 2
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: microcode: 0x219
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: cpu MHz: 1597.071
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: cache size: 512 KB
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: physical id: 0
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: siblings: 4
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: core id: 1
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: cpu cores: 2
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: apicid: 3
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: initial apicid: 3
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: fpu: yes
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: fpu_exception: yes
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: cpuid level: 10
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: wp: yes
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: flags: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
>>>>>>>> mca
>>>>>>>> cmov pat clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm
>>>>>>>> constant_tsc arch_perfmon pebs bts nopl cpuid aperfmperf pni dtes64
>>>>>>>> monitor
>>>>>>>> ds_cpl tm2 ssse3 cx16 xtpr pdcm movbe lahf_lm dtherm
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: bugs:
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: bogomips: 3194.12
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: clflush size: 64
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: cache_alignment: 64
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: address sizes: 32 bits physical, 48 bits virtual
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.cmon:
>>>>>>>> cpuinfo: power management:
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service user.cmon.ComputerMonitor
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service user.crt.CumulusRealTime
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.crt: service
>>>>>>>> version is 0.21
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.crt: realtime
>>>>>>>> txt output goes to /var/www/weerstation/realtime/realtime.txt
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.crt: 'None'
>>>>>>>> values will be displayed as N/A
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.crt: units
>>>>>>>> will be displayed as METRICWX
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.crt: wind
>>>>>>>> units will be displayed as knot
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.crt:
>>>>>>>> zambretti forecast: False
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO user.crt: binding
>>>>>>>> is loop
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service user.crt.CumulusRealTime
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.wxxtypes.StdWXXTypes
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.wxxtypes.StdWXXTypes
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.wxxtypes.StdPressureCooker
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.wxxtypes.StdPressureCooker
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.wxxtypes.StdRainRater
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.wxxtypes.StdRainRater
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.wxxtypes.StdDelta
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.wxxtypes.StdDelta
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.engine.StdArchive
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO weewx.engine:
>>>>>>>> Archive will use data binding wx_binding
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO weewx.engine:
>>>>>>>> Record generation will be attempted in 'hardware'
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO weewx.engine:
>>>>>>>> Using archive interval of 300 seconds (specified in weewx
>>>>>>>> configuration)
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine: Use
>>>>>>>> LOOP data in hi/low calculations: 1
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.engine.StdArchive
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.restx.StdStationRegistry
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO weewx.restx:
>>>>>>>> StationRegistry: Station will be registered.
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.restx.StdStationRegistry
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.restx.StdWunderground
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO weewx.restx:
>>>>>>>> Wunderground: Posting not enabled.
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.restx.StdWunderground
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.restx.StdPWSweather
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO weewx.restx:
>>>>>>>> PWSweather: Posting not enabled.
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.restx.StdPWSweather
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.restx.StdCWOP
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO weewx.restx: CWOP:
>>>>>>>> Data for station FW4650 will be posted
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.restx.StdCWOP
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.restx.StdWOW
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO weewx.restx: WOW:
>>>>>>>> Data for station b24a4cf1-0de4-e611-9401-0003ff5987fb will be posted
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.restx.StdWOW
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.restx.StdAWEKAS
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] INFO weewx.restx:
>>>>>>>> AWEKAS: Posting not enabled.
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.restx.StdAWEKAS
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service user.twitter.Twitter
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.manager:
>>>>>>>> Daily summary version is 4.0
>>>>>>>> May 28 14:00:19 kwsweerstation weewx[11994] DEBUG weewx.manager:
>>>>>>>> Daily summary version is 4.0
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] INFO user.twitter:
>>>>>>>> service version is 0.15
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] INFO weewx.restx:
>>>>>>>> Twitter: No config info. Skipped.
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service user.twitter.Twitter
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service user.windfinder.WindFinder
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] INFO user.windfinder:
>>>>>>>> service version is 0.12
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] INFO user.windfinder:
>>>>>>>> Data will be uploaded for snitser_mar
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service user.windfinder.WindFinder
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.engine.StdPrint
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.engine.StdPrint
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Loading service weewx.engine.StdReport
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Finished loading service weewx.engine.StdReport
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] INFO __main__: Starting
>>>>>>>> up weewx version 4.5.1
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] DEBUG weewx.engine:
>>>>>>>> Station does not support reading the time
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] INFO weewx.engine:
>>>>>>>> Using binding 'wx_binding' to database 'weewx.sdb'
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] INFO weewx.manager:
>>>>>>>> Starting backfill of daily summaries
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] INFO weewx.manager:
>>>>>>>> Daily summaries up to date
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] INFO weewx.engine:
>>>>>>>> Starting main packet loop.
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] DEBUG
>>>>>>>> weewx.drivers.ultimeter: Set station to logger mode
>>>>>>>> May 28 14:00:20 kwsweerstation weewx[11994] DEBUG weewx.manager:
>>>>>>>> Daily summary version is 4.0
>>>>>>>> May 28 14:00:23 kwsweerstation systemd[1]: Stopping LSB: weewx
>>>>>>>> weather system...
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[12001]: * Stopping weewx
>>>>>>>> weather system weewx
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] INFO __main__: Received
>>>>>>>> signal TERM (15).
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] INFO weewx.engine: Main
>>>>>>>> loop exiting. Shutting engine down.
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG weewx.restx: Shut
>>>>>>>> down WindFinder thread.
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG weewx.restx: Shut
>>>>>>>> down WOW thread.
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG weewx.restx: Shut
>>>>>>>> down CWOP thread.
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG weewx.restx: Shut
>>>>>>>> down StationRegistry thread.
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG
>>>>>>>> weewx.drivers.ultimeter: Close serial port /dev/ttyS0
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] INFO __main__:
>>>>>>>> Terminating weewx version 4.5.1
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> **** Traceback (most recent call last):
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> **** File "/usr/share/weewx/weewxd", line 157, in main
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> **** engine.run()
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> **** File "/usr/share/weewx/weewx/engine.py", line 208, in run
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> **** for packet in self.console.genLoopPackets():
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> **** File "/usr/share/weewx/weewx/drivers/ultimeter.py", line 130,
>>>>>>>> in
>>>>>>>> genLoopPackets
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> **** readings =
>>>>>>>> self.station.get_readings_with_retry(self.max_tries,
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> **** File "/usr/share/weewx/weewx/drivers/ultimeter.py", line 259,
>>>>>>>> in
>>>>>>>> get_readings_with_retry
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> **** buf = self.get_readings()
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> **** File "/usr/share/weewx/weewx/drivers/ultimeter.py", line 229,
>>>>>>>> in
>>>>>>>> get_readings
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> **** c = self.serial_port.read(1)
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> **** File "/usr/lib/python3/dist-packages/serial/serialposix.py",
>>>>>>>> line
>>>>>>>> 483, in read
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> **** ready, _, _ = select.select([self.fd,
>>>>>>>> self.pipe_abort_read_r],
>>>>>>>> [], [], timeout.time_left())
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> **** File "/usr/share/weewx/weewxd", line 260, in sigTERMhandler
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> **** raise Terminate
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[11994] DEBUG __main__:
>>>>>>>> **** Terminate
>>>>>>>> May 28 14:00:23 kwsweerstation weewx[12001]: ...done.
>>>>>>>> May 28 14:00:23 kwsweerstation systemd[1]: weewx.service: Succeeded.
>>>>>>>> May 28 14:00:23 kwsweerstation systemd[1]: Stopped LSB: weewx
>>>>>>>> weather system.
>>>>>>>>
>>>>>>>> --
>>>>>>>> You received this message because you are subscribed to the Google
>>>>>>>> Groups "weewx-user" group.
>>>>>>>> To unsubscribe from this group and stop receiving emails from it,
>>>>>>>> send an email to weewx-user+...@googlegroups.com.
>>>>>>>> To view this discussion on the web visit
>>>>>>>> https://groups.google.com/d/msgid/weewx-user/4a059e50-2fd5-4daa-80d6-ebcecccf46can%40googlegroups.com
>>>>>>>> <https://groups.google.com/d/msgid/weewx-user/4a059e50-2fd5-4daa-80d6-ebcecccf46can%40googlegroups.com?utm_medium=email&utm_source=footer>
>>>>>>>> .
>>>>>>>>
>>>>>>> --
>>>>>> You received this message because you are subscribed to the Google
>>>>>> Groups "weewx-user" group.
>>>>>> To unsubscribe from this group and stop receiving emails from it,
>>>>>> send an email to weewx-user+...@googlegroups.com.
>>>>>>
>>>>> To view this discussion on the web visit
>>>>>> https://groups.google.com/d/msgid/weewx-user/909270b6-c0a8-436a-a7bf-e6a2a50e3b48n%40googlegroups.com
>>>>>> <https://groups.google.com/d/msgid/weewx-user/909270b6-c0a8-436a-a7bf-e6a2a50e3b48n%40googlegroups.com?utm_medium=email&utm_source=footer>
>>>>>> .
>>>>>>
>>>>> --
>>> You received this message because you are subscribed to the Google
>>> Groups "weewx-user" group.
>>> To unsubscribe from this group and stop receiving emails from it, send
>>> an email to weewx-user+...@googlegroups.com.
>>>
>> To view this discussion on the web visit
>>> https://groups.google.com/d/msgid/weewx-user/6f526cac-1942-461d-bfb3-d743bfc2cef6n%40googlegroups.com
>>> <https://groups.google.com/d/msgid/weewx-user/6f526cac-1942-461d-bfb3-d743bfc2cef6n%40googlegroups.com?utm_medium=email&utm_source=footer>
>>> .
>>>
>> --
> You received this message because you are subscribed to the Google Groups
> "weewx-user" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to weewx-user+unsubscr...@googlegroups.com.
> To view this discussion on the web visit
> https://groups.google.com/d/msgid/weewx-user/8662189b-7232-428a-a6f7-02d0e7635262n%40googlegroups.com
> <https://groups.google.com/d/msgid/weewx-user/8662189b-7232-428a-a6f7-02d0e7635262n%40googlegroups.com?utm_medium=email&utm_source=footer>
> .
>
--
You received this message because you are subscribed to the Google Groups
"weewx-user" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to weewx-user+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/weewx-user/CAPq0zECV4q2eqT_7BbYOttBw%2BD9Hm5My2i651WWvzxepTuTiMg%40mail.gmail.com.
