FWIW, my 3650 link seems to have a slight Austrian accent. Randy
Mac Dearman wrote: > Randy, > > Thanks for the link. Turns out we are ok since we leave all our settings > at default, but it could have been very important. I wasn't aware of Ubnt > doing any testing with MT. That's just good knowledge - thanks. > > Mac > > > > > >> -----Original Message----- >> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On >> Behalf Of Randy Cosby >> Sent: Thursday, October 30, 2008 10:39 AM >> To: WISPA General List >> Subject: Re: [WISPA] MikroTik and UBQ XR3 >> >> Also, when working with UBNT cards and Mikrotik, be sure you are >> adjusting for correct power settings. See >> http://www.ubnt.com/downloads/ubi_mtik_power.pdf for a pretty thorough >> explanation. >> >> Randy >> >> >> Kurt Fankhauser wrote: >> >>> I use the brazil country code. On the main wireless tab under >>> >> frequency mode >> >>> make sure that you have selected "manual_txpower" instead of >>> >> "regulatory >> >>> domain" or it will try to limit your power due to local regulatory >>> >> laws >> >>> without you knowing. >>> >>> Kurt Fankhauser >>> WAVELINC >>> P.O. Box 126 >>> Bucyrus, OH 44820 >>> 419-562-6405 >>> www.wavelinc.com >>> >>> >>> -----Original Message----- >>> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] >>> >> On >> >>> Behalf Of [EMAIL PROTECTED] >>> Sent: Thursday, October 30, 2008 1:45 AM >>> To: 'WISPA General List' >>> Subject: [WISPA] MikroTik and UBQ XR3 >>> >>> We are testing a 3.65 GHz setup with MT and XR3 using a 11 dBi Omni >>> >> and 14 >> >>> dBi panel. My results are not really impressive with signal levels. >>> >> However, >> >>> In order to use 3663 MHz you must set the card for 5770 MHz and 5770 >>> >> MHz is >> >>> not available unless you purchase a special frequency license for >>> >> each ap >> >>> and cpe from MT. However someone on the list pointed out that >>> >> selecting a >> >>> different country other than the good old USA would allow you to >>> >> select the >> >>> 5770 Mhz frequency. This is true and we used the Germany 5ghz ptp >>> >> setting >> >>> for country and we now have the needed 5770 Mhz frequency available >>> >> for >> >>> selection. So now I am starting to wonder if this may be the reason >>> >> we are >> >>> getting less than anticipated results with signal levels. So now >>> >> finally the >> >>> real question I am asking; is there really a difference between >>> >> purchasing a >> >>> special frequency license from MT and using the cheat of selecting a >>> different country in order to select 5770 Mhz? Isn't 5770 Mhz still >>> >> 5770 Mhz >> >>> no matter what? >>> >>> >>> >>> Thanks, >>> >>> John Buwa >>> >>> Michiana Wireless >>> >>> >>> >>> >>> >>> --------------------------------------------------------------------- >>> >> ------- >> >>> ---- >>> WISPA Wants You! Join today! >>> http://signup.wispa.org/ >>> --------------------------------------------------------------------- >>> >> ------- >> >>> ---- >>> >>> WISPA Wireless List: wireless@wispa.org >>> >>> Subscribe/Unsubscribe: >>> http://lists.wispa.org/mailman/listinfo/wireless >>> >>> Archives: http://lists.wispa.org/pipermail/wireless/ >>> >>> >>> >>> --------------------------------------------------------------------- >>> >> ----------- >> >>> WISPA Wants You! Join today! >>> http://signup.wispa.org/ >>> --------------------------------------------------------------------- >>> >> ----------- >> >>> WISPA Wireless List: wireless@wispa.org >>> >>> Subscribe/Unsubscribe: >>> http://lists.wispa.org/mailman/listinfo/wireless >>> >>> Archives: http://lists.wispa.org/pipermail/wireless/ >>> >>> >> -- >> Randy Cosby >> Vice President >> InfoWest, Inc >> >> office: 435-773-6071 >> >> >> >> >> ----------------------------------------------------------------------- >> --------- >> WISPA Wants You! Join today! >> http://signup.wispa.org/ >> ----------------------------------------------------------------------- >> --------- >> >> WISPA Wireless List: wireless@wispa.org >> >> Subscribe/Unsubscribe: >> http://lists.wispa.org/mailman/listinfo/wireless >> >> Archives: http://lists.wispa.org/pipermail/wireless/ >> No virus found in this incoming message. >> Checked by AVG - http://www.avg.com >> Version: 8.0.175 / Virus Database: 270.8.3/1748 - Release Date: >> 10/26/2008 7:53 PM >> > > > > -------------------------------------------------------------------------------- > WISPA Wants You! Join today! > http://signup.wispa.org/ > -------------------------------------------------------------------------------- > > WISPA Wireless List: wireless@wispa.org > > Subscribe/Unsubscribe: > http://lists.wispa.org/mailman/listinfo/wireless > > Archives: http://lists.wispa.org/pipermail/wireless/ > -- Randy Cosby Vice President InfoWest, Inc office: 435-773-6071 -------------------------------------------------------------------------------- WISPA Wants You! Join today! http://signup.wispa.org/ -------------------------------------------------------------------------------- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
