I have you tried just setting your MT to a different country and see if it becomes available? I know brazil gives you access to above the 2462 limit which is nice because we can you much more above that in unlicensed spectrum.
-Cameron -----Original Message----- From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Mike Sent: Wednesday, September 09, 2009 2:07 PM To: WISPA General List Subject: Re: [WISPA] 2.4 Frequency coordination And when I look at wireless info, I see this: 2ghz-b-channels=2412:0,2417:0,2422:0,2427:0,2432:0,2437:0,2442:0,2447:0, 2452:0,2457:0,2462:0 So the Extended Frequency License will allow me to modify these? Any other way? I'd hate to have to buy an extra license for every CPE device. I would however buy one for the AP. It may steer me away from using MT for these customer sites IF I decide to try this. Mike ******************************* Good idea, but it won't let me. I receive this message: message=bad band and/or channel, see 'wireless info' for supported channels;code=4 Apparently, it IS possible with the Wili cards, but still don't have a total answer to my query. Can anybody help a fellow WISPA member? Hasn't anybody thought about doing this or is doing this? You could squeeze a couple more sectors on a tower if this is possible. Mike At 08:36 AM 9/9/2009, you wrote: >I believe you can but you'll need to use the CLI > >Int wireless set wlan1 frequency=2406 >On 9/9/09, Mike <m...@aweiowa.com> wrote: > > I have some questions on the frequency agility of Mikrotik equipment, > > FCC regs, and frequency coordination. > > > > There are 3 non-overlapping channels at 2.4G; 1, 6 and 11. That > > makes an assumption we are using 20MHz channel size. > > > > Some of the newer radios can run 10MHz and 5MHz channel sizes. > > > > Using the RouterOS interface, the only choice for channel selection > > is the center frequency of each of the 11 channels available in the > > US. So, the only choice, say for channel 1 is 2412MHz. When using > > 20MHz channel size, the RF will occupy 2401 to 2423 according to FCC > > rules, on channel 1. > > > > If I want to deploy a device capable of running 10MHz channel width, > > is there a way to set the channel frequency to say 2406? The signal > > would occupy 2401 to 2411, and still be within the definition of channel 1. > > > > Would a Mikrotik Extended Frequency License allow this frequency > > agility? Would every CPE connected to such an AP also be required to > > have the license? Is this within FCC rules? > > > > Are any of you doing this? If so, what equipment are you using? > > > > Thanks! Mike > > > > > > > > > > > ------------------------------------------------------------------------ -------- > > WISPA Wants You! Join today! > > http://signup.wispa.org/ > > > ------------------------------------------------------------------------ -------- > > > > WISPA Wireless List: wireless@wispa.org > > > > Subscribe/Unsubscribe: > > http://lists.wispa.org/mailman/listinfo/wireless > > > > Archives: http://lists.wispa.org/pipermail/wireless/ > > > > >-- >Josh Luthman >Office: 937-552-2340 >Direct: 937-552-2343 >1100 Wayne St >Suite 1337 >Troy, OH 45373 > >"When you have eliminated the impossible, that which remains, however >improbable, must be the truth." >--- Sir Arthur Conan Doyle > > >----------------------------------------------------------------------- --------- >WISPA Wants You! Join today! >http://signup.wispa.org/ >----------------------------------------------------------------------- --------- > >WISPA Wireless List: wireless@wispa.org > >Subscribe/Unsubscribe: >http://lists.wispa.org/mailman/listinfo/wireless > >Archives: http://lists.wispa.org/pipermail/wireless/ ------------------------------------------------------------------------ -------- WISPA Wants You! Join today! http://signup.wispa.org/ ------------------------------------------------------------------------ -------- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ -------------------------------------------------------------------------------- WISPA Wants You! Join today! http://signup.wispa.org/ -------------------------------------------------------------------------------- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/