You are the only 77bit. plenty of old format. On Tue, 27 Nov 2018 at 10:48, Ken Myers <kenmyersglo...@gmail.com> wrote:
> Thanks Steve Sanity regained!!! > > On Tue, 27 Nov 2018 at 10:43, Stephen Ireland <vk3...@hotmail.com> wrote: > >> Ken (and others), >> >> >> >> I am actually sending now (27/11/18 UTC 00:30) main band 20m at 1550 Hz. >> >> Everyone so no screaming about operating above 2K in offset as I am >> interested in the interaction between v1 and v2 sigs. >> >> >> >> I have been doing so for around 5 mins on a rather active band ... I will >> do so for around another hour or so. >> >> >> >> 73 >> >> >> >> Steve I >> >> >> >> Sent from Mail <https://go.microsoft.com/fwlink/?LinkId=550986> for >> Windows 10 >> >> >> ------------------------------ >> *From:* Ken Myers <kenmyersglo...@gmail.com> >> *Sent:* Tuesday, November 27, 2018 11:31:14 AM >> *To:* wsjt-devel@lists.sourceforge.net >> *Subject:* Re: [wsjt-devel] 2RSC3 > 2RSC4 decoding disappeared FT8 >> >> 1 decode on 20m - frq 383 ?? seems to work. Like fishing - have to wait >> quietly or NOISILY sent out string of CQ - no fish. Checking 6m >> >> THanks >> >> >> On Tue, 27 Nov 2018 at 09:53, Ken Myers <kenmyersglo...@gmail.com> wrote: >> >>> Thanks - shall persist >>> >>> Cheers Ken >>> VK4GC >>> >>> On Tue, 27 Nov 2018 at 09:42, Bill Somerville <g4...@classdesign.com> >>> wrote: >>> >>>> Hi Ken, >>>> >>>> comments in line below. >>>> >>>> On 26/11/2018 23:15, Ken Myers wrote: >>>> > 2 installations - >>>> > 1 MSSurface Win10 up to date, 2 radios (FT991a & FTdx3000 both USB) >>>> - >>>> > non decode, >>>> > 2 HP Allinone with FT897/Singnalink. - non decode, >>>> > (both setups using HRD (up to date) for CAT control) >>>> This combination of rig and interface requires a specific setup. The >>>> FT-817/857/897(D) series of rigs do not accept CAT commands while >>>> transmitting. You must *not* check the settings option >>>> "Settings->General->Allow Tx frequency changes while transmitting" and >>>> you must set the SignaLink delay knob to minimum. You should set the >>>> WSJT-X PTT configuration "Settings->Radio->PTT Method" to "VOX" >>>> although >>>> some have found it necessary to use the CAT PTT Method to avoid any CAT >>>> commands while the rig is in Tx mode. >>>> > >>>> > For all: >>>> > 1.9.1 works great >>>> > 2.0 RC3 works great >>>> > 2.0 RC4 good waterfall (therefore good audio present) - NO decode. >>>> > >>>> > uninstalling/reinstalling forward and back through versions gives the >>>> > same result. >>>> > >>>> > i have concluded: >>>> > 1 I must be holding my mouth wrong - OR >>>> > 2 I have missed a new setting. >>>> > 3 When I have been looking/testing RC4, no RC4 (77 bit) >>>> > transmissions. Not sure here as I have been especially been looking >>>> > top band. >>>> > >>>> > 2 probably!! >>>> > >>>> Almost certainly 3, there has been a relatively low usage to 77-bit FT8 >>>> on the normal HF FT8 sub-bands. It seems that most users of RC4 have >>>> reverted to v1.9.1 so the volume of 77-bit traffic is low except for a >>>> couple of days after a beta release. It would be good if users of RC5 >>>> could stick with it and try to drive up the level of activity so that >>>> issues can be discovered before the final GA release. >>>> >>>> 73 >>>> Bill >>>> G4WJS. >>>> >>>> >>>> >>>> _______________________________________________ >>>> wsjt-devel mailing list >>>> wsjt-devel@lists.sourceforge.net >>>> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >>>> >>> >>> >>> -- >>> Cheers >>> >>> Ken Myers >>> >>> Sunnybank Hills QLD AUS >>> M +61 414 487 004 >>> >>> >> >> -- >> Cheers >> >> Ken Myers >> >> Sunnybank Hills QLD AUS >> M +61 414 487 004 >> >> _______________________________________________ >> wsjt-devel mailing list >> wsjt-devel@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >> > > > -- > Cheers > > Ken Myers > > Sunnybank Hills QLD AUS > M +61 414 487 004 > > -- Cheers Ken Myers Sunnybank Hills QLD AUS M +61 414 487 004
_______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
