Uwe, Yes. That was the problem. I had just discovered and fixed that, and found your email. For some unknown reason BkTimeSync had stopped working. It was on trial anyway, and was doing a good job. However when I was running Meinberg, I never had a seconds trouble.
Thanks Uwe/ __________ Dan – K4SHQ From: DG2YCB, Uwe [mailto:dg2...@gmx.de] Sent: Tuesday, December 11, 2018 1:43 PM To: 'WSJT software development' <wsjt-devel@lists.sourceforge.net> Subject: Re: [wsjt-devel] Is it just me? v2.0? Dan, does your PC time eventually need to be synchronized? Check deviation at https://time.is/ 73 de Uwe, DG2YCB Von: Dan Malcolm [mailto:k4...@outlook.com] Gesendet: Dienstag, 11. Dezember 2018 20:30 An: 'WSJT software development' Betreff: Re: [wsjt-devel] Is it just me? v2.0? Thanks John, I usually call CQ 10 or more times, after setting tx/rx to a clear spot. My power meter shows power out, so I am at least transmitting. I am on 7.074 as Joe suggested, but I have my tx/rx bandwidth set to 4k so I can see well up the band. One of the advantages of an SDR. Sound card setting are as they should be and that verified because I can transmit and receive. The waterfall shows more than a dozen signals but none are decoded. I should mention that I had a similar experience on 20m this morning. After posting the original email, I tried stepping bat to c1.9.1. No help. I am running VM Banana for Virtual Audio and it’s been solid since installation several months ago. __________ Dan – K4SHQ From: John Scheuer [mailto:johnusche...@gmail.com] Sent: Tuesday, December 11, 2018 1:11 PM To: wsjt-devel@lists.sourceforge.net<mailto:wsjt-devel@lists.sourceforge.net> Subject: Re: [wsjt-devel] Is it just me? v2.0? Dan, What freq are you using on 40. I always use 7075. My freq gets changed once in a while and I find I am not on the freq I think I am. hi. I use PSK Reporter. Might give that a try and see if it shows anything different. When the rig is keyed does it show out put power. I had a problem a while back. The rig was keyed but no out put. One other thing you may want to check is your sound cards. I had a problem with erratic behavior and found for some unknown reason the cards were changing. I don't know if I ever figured out why but it's been working fine for some time now. When you call cq it may take a while. If you are only calling 3 or 4 times I think you're a bit optimistic. hi I look on the waterfall for what apears to be a clear spot and set my receive and xmit there. Hope that helps, John-NA6Y I am also running 2.0 On Tue, Dec 11, 2018 at 1:47 PM Dan Malcolm <k4...@outlook.com<mailto:k4...@outlook.com>> wrote: Yesterday I downloaded and installed v2.0. No issue installing, and made a QSO on the first run. Made several other QSO’s during the day, and thought all was well. This morning? Nada…..nothing….sort of. I am getting a few decodes on 40 and 20 but it’s sparse. Enough to indicate decoding is working. Then I tried calling CQ several time with no results whatever. Even HamSpots says that I haven’t been heard in more than a day. So do I just be patient and wait for a bigger v2.0 population or do I have a problem? I suspect I am just being impatient. __________ Dan – K4SHQ _______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net<mailto:wsjt-devel@lists.sourceforge.net> https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
