Not the squelch, but it was my PC’s time sync program that quit working. It was BkTimeSync and was on trial, doing a good job, till last night, when it locked up. I normally use Meinberg. I think I’ll go back to it.
__________ Dan – K4SHQ From: John Scheuer [mailto:johnusche...@gmail.com] Sent: Tuesday, December 11, 2018 2:26 PM To: wsjt-devel@lists.sourceforge.net Subject: Re: [wsjt-devel] Is it just me? v2.0? I can appreciate what you're going through Dan believe me. HI. Is it possible that the squelch is involved, this could cause it to act erratic. Since it works some of the time it got me thinking. John On Tue, Dec 11, 2018 at 2:34 PM Dan Malcolm <k4...@outlook.com<mailto:k4...@outlook.com>> wrote: Thanks John, I usually call CQ 10 or more times, after setting tx/rx to a clear spot. My power meter shows power out, so I am at least transmitting. I am on 7.074 as Joe suggested, but I have my tx/rx bandwidth set to 4k so I can see well up the band. One of the advantages of an SDR. Sound card setting are as they should be and that verified because I can transmit and receive. The waterfall shows more than a dozen signals but none are decoded. I should mention that I had a similar experience on 20m this morning. After posting the original email, I tried stepping bat to c1.9.1. No help. I am running VM Banana for Virtual Audio and it’s been solid since installation several months ago. __________ Dan – K4SHQ From: John Scheuer [mailto:johnusche...@gmail.com<mailto:johnusche...@gmail.com>] Sent: Tuesday, December 11, 2018 1:11 PM To: wsjt-devel@lists.sourceforge.net<mailto:wsjt-devel@lists.sourceforge.net> Subject: Re: [wsjt-devel] Is it just me? v2.0? Dan, What freq are you using on 40. I always use 7075. My freq gets changed once in a while and I find I am not on the freq I think I am. hi. I use PSK Reporter. Might give that a try and see if it shows anything different. When the rig is keyed does it show out put power. I had a problem a while back. The rig was keyed but no out put. One other thing you may want to check is your sound cards. I had a problem with erratic behavior and found for some unknown reason the cards were changing. I don't know if I ever figured out why but it's been working fine for some time now. When you call cq it may take a while. If you are only calling 3 or 4 times I think you're a bit optimistic. hi I look on the waterfall for what apears to be a clear spot and set my receive and xmit there. Hope that helps, John-NA6Y I am also running 2.0 On Tue, Dec 11, 2018 at 1:47 PM Dan Malcolm <k4...@outlook.com<mailto:k4...@outlook.com>> wrote: Yesterday I downloaded and installed v2.0. No issue installing, and made a QSO on the first run. Made several other QSO’s during the day, and thought all was well. This morning? Nada…..nothing….sort of. I am getting a few decodes on 40 and 20 but it’s sparse. Enough to indicate decoding is working. Then I tried calling CQ several time with no results whatever. Even HamSpots says that I haven’t been heard in more than a day. So do I just be patient and wait for a bigger v2.0 population or do I have a problem? I suspect I am just being impatient. __________ Dan – K4SHQ _______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net<mailto:wsjt-devel@lists.sourceforge.net> https://lists.sourceforge.net/lists/listinfo/wsjt-devel _______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net<mailto:wsjt-devel@lists.sourceforge.net> https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
